Displays2go IPDTBL3 Bedienungsanleitung

iPad IPDTBL3

Assembly Instructions

1

Carefully lay all posts horizontally on floor. Insert 4 foot screws

into 4 posts except 1m post with connector bars.

WARNING – Dome-headed

chrome nuts behind enclosure

housing must not be adjusted.

3Feed figure-8 head of

power lead through

bottom of post and

profiles assembly, leaving

approximately 1m of

cable at bottom.

4Stand post and profiles

assembly upright ensuring

lead is kept clear of foot

screws.

Take 265mm post and slot clamp of three 220mm profiles into

desired channels for display. Ensure bottom of profiles are flush

with bottom of post and tighten grub screws to secure in position.

If you are not using cable management for charging, please

carefully stand post and profiles assembly upright and proceed to

Stage 6

2

5

Feed figure-8 head of power lead through 1m post at connector

bar end, so it protrudes from top of post.

Loosen and slide connector bars halfway out of 1m post. Tighten

grub screws of connector bars positioned in post channel to secure

6

7

Connect the 1m and 265mm posts by locating connector bars into

channels and sliding together. Tighten remaining grub screws to

affix.

With countersunk holes in the Podium tops uppermost, align with

holes of circular plates and fixings in the top of remaining small,

medium and large posts. Fully insert 4 screws in each to secure.

8

9

Starting with the smallest Podium table, position and slot clamp of one

220mm profile into post channel. Tighten grub screw to attach. Repeat

process for medium and large Podium tables.

11

Plug figure-8 head into USB Power Adapter (supplied with Apple

iPad).

Position remaining 220mm profiles between posts near underside

of Podium tops. Insert clamps into channels and secure by

tightening grub screws.

If you are not using cable management for charging, please

proceed to Stage 17.

10

13

Lift fascia out of enclosure. Insert cable (supplied with Apple iPad)

allowing 10cm to remain “free” at charge/sync connector end by

gently pressing into retaining moulding.

12

Unlock the iPad enclosure by inserting key into security lock and

rotate ‘QUARTER TURN ONLY’ clockwise or counter-clockwise

through 90 degrees which releases the locking pin. Return key back

to original position to remove.

15

Plug cable into USB Power Adapter.Feed USB end of charge/sync cable through middle of enclosure,

below pin, so it protrudes from bottom of support column.

14

17

Align first 2 holes of the iPad holder to the threads of the post.

Insert and tighten screws to secure. Rotate iPad holder through 90º,

aligning remaining 2 holes to threads of post. Insert and tighten

screws to secure.

Position black mains cable into internal post channel, and carefully

slide USB Power Adapter inside post so the USB head of charge/sync

cable is below upper edge of post.

16

Andere Displays2go Rack & Stand Handbücher

Displays2go

Displays2go WL3SDSG Bedienungsanleitung

Displays2go

Displays2go DSTANDBK Bedienungsanleitung

Displays2go

Displays2go VWALL3+ VWALLB Bedienungsanleitung

Displays2go

Displays2go CDSTAND2BK Bedienungsanleitung

Displays2go

Displays2go MGWLSBK Bedienungsanleitung

Displays2go

Displays2go LECTWFANAO Bedienungsanleitung

Displays2go

Displays2go RCCDIGITALS Bedienungsanleitung

Displays2go

Displays2go SMMGRDS Bedienungsanleitung

Displays2go

Displays2go ARTTV70B Bedienungsanleitung

Displays2go

Displays2go CFSTN2B Bedienungsanleitung

Displays2go

Displays2go LM3255TLT Bedienungsanleitung

Displays2go

Displays2go DGMLTSBK Bedienungsanleitung

Displays2go

Displays2go NAVIGATOR Series Bedienungsanleitung

Displays2go

Displays2go ECOSOC66 Bedienungsanleitung

Displays2go

Displays2go QSCT1117WD Bedienungsanleitung

Displays2go

Displays2go FGAHSCBDK Bedienungsanleitung

Displays2go

Displays2go LTMLT2AV1 Bedienungsanleitung

Displays2go

Displays2go PEDLEDSV Bedienungsanleitung

Displays2go

Displays2go MSHWL Series Bedienungsanleitung

Displays2go

Displays2go SMAWRDCSC Bedienungsanleitung

Displays2go

Displays2go PROMXMN Bedienungsanleitung

Displays2go

Displays2go TVM110B Bedienungsanleitung

Displays2go

Displays2go MNTW803L Bedienungsanleitung

Displays2go

Displays2go SM3TWDR Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung