LT-1289 20171 © 2020 Digital Monitoring Products, Inc.
7. TRANSMITTER SURVEY LED OPERATION
1100 Series transmitters provide a survey operation that allows one
person to confirm that each transmitter is communicating with the
wireless receiver or panel to easily determine the best location for the
transmitters and the wireless receiver. Follow the directions below to test
communication of the wireless transmitters:
1. Remove the transmitter’s cover.
2. Hold the transmitter in the desired location.
3. Press the tamper switch to send data to the wireless receiver and
determine if communication is confirmed or faulty.
Confirmed: If communication is confirmed, the survey LED turns
on when data is sent to the wireless receiver and o when
acknowledgment is received.
Faulty: If communication is faulty, the LED remains on for several
seconds or flashes multiple times in quick succession. Relocate
the transmitter or the wireless receiver until the LED confirms
clear communication. Proper communication between the
transmitter and wireless receiver is verified when for each press
or release of the tamper switch, the transmitter’s LED blinks
immediately on and immediately o.
8. IF 1100R REPEATER IS NEEDED:
Select a Location
Mount the 1100R on a flat surface. The 1100R Wireless Repeater is
typically mounted between the 1100 Series Receiver and the 1100 Series
transmitter(s) that are out of range. Locate as far from the 1100 Receiver
as needed to provide the required system range. Install the repeater away
from large metal objects. Mounting the repeater on or near metal surfaces
impairs performance. If the repeater is powered from an auxiliary power
supply, mount the repeater away from the metal power supply enclosure.
If the repeater is powered from the optional Model 376L plug-in power
supply, locate the repeater near a wall outlet not controlled by a switch.
When selecting the proper mounting location of a repeater, refer to the
LED Survey Operation section to confirm communication with the 1100
Receiver.
Tamper Switches
The 1100R is equipped with a case tamper and a wall tamper. A two
position header is provided to disable the wall tamper. To disable the wall
tamper, place the jumper across the two pins of the header. If wall tamper is
required, place the jumper over just one pin for storage.
Mounting the Receiver
1. Insert a small screwdriver and lift, as discussed in Mount the Receiver,
to remove the cover.
2. Secure the receiver to the wall ensuring that the wall tamper switch
makes proper contact with the wall. Use the supplied screws in the
mounting hole locations as shown in Figure 2.
3. Snap the cover back on the unit after observing LED operation.
6. 1100D RECEIVER OPERATION
The 1100D receiver automatically sends the panel house code to wireless
transmitters when the unique transmitter serial number is programmed into
the panel. The house code identifies the panel, receiver, and transmitters to
each other. The receiver only listens for transmissions using the specified
house code and/or programmed transmitter serial number.
Note: When setting up a wireless system, it is recommended to
program zones and connect the receiver before installing batteries in
the transmitters.
When a receiver is installed, powered up, or the panel is reset, the
supervision time for transmitters is reset. If the receiver has been powered
down for more than one hour, wireless transmitters may take up to an
additional hour to send a supervision message unless tripped, tampered,
or powered up. This operation extends battery life for transmitters. A
missing message may display on the keypad until the transmitter sends a
supervision message.
When any wireless zone programming is changed in the panel, receiver
zone programming is updated when exiting panel programming. During the
update, all wireless zones display as normal for approximately one minute,
regardless of the actual state of the wireless device(s).
External DC Plug-in Power Supply
When using the optional Model
376L plug-in DC power supply, use
the following steps to connect the
power supply:
1. Connect the Black wire with
White stripe to the positive
terminal on the 1100R and the
Black wire to the negative
terminal. See Figure 4.
2. Mount the 1100R near a wall outlet.
In addition to powering the repeater, the DC plug-in power supply also
charges the back-up battery. The 376L plug-in DC power supply must be
located within 100 feet of the repeater using 22 AWG wire or 250 feet using
18 AWG wire.
Optional Powering from External 12 VDC Power Supply
The 1100R can be powered from a 12 VDC
power supply such as a DMP Model 505-12. In
addition to powering the repeater, the power
supply also charges the back-up battery
of the repeater. If the DC power source is
removed, the power failure is indicated as an
open condition on the repeater zone.
Use the following steps to connect the power
supply:
1. Using 22 AWG wire, connect the J3 DC
Power 2-position Terminal Block to the
J6 terminalon the 505-12 power supply
PCB. See Figure 5.
2. Observe positive and negative polarity
on all connections.
Primary Power Loss Indication
When the 1100R is used with the XT Series or XTL Series a zone trouble
indication for the repeater zone occurs within three minutes of a loss of
primary power.
When used with the XR150/XR550 Version 206 or higher, a power loss
indication is displayed at the keypad as -ACPWR for the repeater zone. This
occurs within three minutes but a zone trouble report to the Central Station
receiver is delayed for one hour.
Rechargeable Battery
The 1100R rechargeable battery is used to provide up to 24 hours of backup
battery power when AC power is not available. The battery is intended for
backup power only and not to operate the 1100R Repeater on a daily basis.
If the battery is low, or not plugged into the J4 battery connector, a low
battery condition is indicated for the repeater zone.
Keypad Bus Wiring
The 1100D Wireless Receiver easily interfaces with the XT30/XT50 Series
panels using the keypad bus.
Harness Connection
Refer to Figure 3, the panel programming guide and use the following steps
to connect the panel and receiver:
1. Using a 4-wire harness, connect from the 1100D Wireless Receiver
header (see Figure 3) to the panel keypad bus terminals 7, 8, 9, and
10. Observe wire colors when connecting to the terminals.
2. In System Options, program the House Code (1-50). In Zone
Information, program the wireless zones.
RYGB
TO PANEL
Black
Green
Yellow
Red
J4
RED PRO
J8
XT30/XT50 Series Panel
J7
RJ SUP
AC
1234567
810 11 12
9
+B BELL GND SMK
RED YEL GRN BLKAC -B
1100D
Receiver
Can be extended
up to 500 feet
from the panel
using 22 AWG
Figure 3: 1100D Series Wiring
Figure 5: 1100D Series
Mounting Holes
+ DC -
505-12 Power
Supply
12 VDC @
2 Amps
22 AWG Wire
DC Power
2-position
Terminal Block
DC
Plug-in
Power
Supply
DC Power
2-position
Terminal Block
- +
- +
Black Wire
with White Stripe
to Positive Black Wire
to Negative
Figure 4: DMP 376L Wiring
