DMP Electronics 738ZplusINT Bedienungsanleitung

738ZplusINT Z-WAVE INTERFACE

MODULE

Installation Guide

DESCRIPTION

1SELECT THE LOCATION

Select a central location for the 738ZplusINT Z-Wave Interface

Module. Keep in mind that at least one Z-Wave Plus device must

be within 65 feet of the module. Most Z-Wave Plus devices act as

repeaters for the signal to create longer and multiple transmission

routes (battery-powered Z-Wave Plus devices do not repeat signals

in order to extend battery life). See Figure 2.

Note: Place the module away from large, metal objects to

avoid interference with the Z-Wave Plus signal.

2MOUNT THE 738ZplusINT

1. With the housing cover o, carefully remove the

738ZplusINT’s PCB from the housing.

2. Use the supplied screws to secure the 738ZplusINT housing

against a wall or ﬂat surface. See Figure 3.

The 738ZplusINT Z-Wave Interface

Module allows DMP panels to

communicate with up to 140

Z-Wave or Z-Wave Plus devices,

such as light controls, light bulbs,

door locks, garage door openers,

and thermostats.

The 738ZplusINT is automatically

recognized by DMP panels, and no

additional programming is required.

Once the module is connected to a

DMP panel, users can immediately

begin adding Z-Wave devices to

their system.

Devices can be remotely controlled

from smart phones using the DMP

Virtual Keypad™ App.

Figure 2: Example Z-Wave Plus Transmission Routes

= Z-Wave Plus Device

Oce Dining

Living Room

Foyer

Kitchen

Garage

Control

Panel with

738ZplusINT

Figure 3: 738ZplusINT Housing with Mounting Holes

Mounting Holes

Figure 1: 738ZplusINT Z-Wave

Interface Module

Compatibility

• DMP XT30INT/XT50INT

Series panels

• DMP XR150INT/XR550INT

Series panels

• All Z-Wave and Z-Wave

Plus devices

• See the Compatibility section for

complete information.

What is Included?

• 738ZplusINT Z-Wave

Interface Module

• Hardware pack

2 738Zplus INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS

4ADD DEVICES

After wiring the 738ZplusINT to the panel, use a DMP keypad to program Z-Wave Plus devices into the

panel through the User Menu Z-Wave Setup option. This allows users to add devices through the User Menu

or the Virtual Keypad™ app after installation. When possible, have the Z-Wave device near the module

during setup and programming.

When programming Z-Wave devices into an XT30INT or XT50INT panel with Version 171 or higher, you can

add multiple devices at once. If you add multiple devices at once, then you will name each device after they

have all been added.

Note: To add the 738ZplusINT to an existing network, use the LRN (Learn) function.

1. Press CMD until MENU? YES NO appears, then press YES.

2. Press CMD until ZWAVE SETUP? appears. Press any select key or area.

3. Select ADD. The screen displays PROCESSING.

4. When prompted, press the button (or series of buttons if adding a thermostat) on the device you

are adding.

5. The keypad displays that the device has connected to your system.

3WIRE THE 738ZplusINT

The 738ZplusINT has four wire connections to connect to

the panel’s keypad bus. See Figure 4.

1. Connecting the wires to the 738ZplusINT terminals.

a. Connect the wire that delivers power to the

module to the RED terminal.

b. Connect the wire that sends data from the

module to the YEL terminal.

c. Connect the wire that receives data from

the panel to the GRN terminal.

d. Connect the ground wire to the BLK

terminal.

2. Carefully place the 738ZplusINT PCB back into

the housing, and then snap the housing cover

into place.

3. At the panel, connect the wires to the keypad bus

corresponding terminals.

Figure 4: 738ZplusINT Module

Wiring Connections

To Keypad Bus

REMOVE OR REPLACE DEVICES

If a device fails, users can remove or replace the device through the User Menu.

1. Press CMD until MENU? YES NO appears, then press YES.

2. Press CMD until ZWAVE SETUP? appears. Press any select key or area.

3. Select LIST and press CMD until the device you are removing or replacing displays. Then, press any

select key or area to select the device.

4. Select STATUS. The status of the device displays as either OKAY or FAILED. If the device fails,

REMOVE FAILED DEVICE displays.

5. Select YES to remove the device. Press the second select key or area to replace the device.

6. If you chose to replace the device, PROCESSING displays.

7. When prompted, press the button (or series of buttons if adding a thermostat) on the replacement

device.

8. The keypad displays that the device has connected to your system.

Note: The replacement device keeps the original device’s name.

738Zplus INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3

ADDITIONAL INFORMATION

LED Operation

The 738ZplusINT has three LEDs on the PCB that allow you to determine what type of operation is occurring. See Figure

4 for LED locations.

• PTX Green LED - If the light is blinking, then data is being sent to the panel.

• ZTX Green LED - If the light is blinking, then data is being sent to Z-Wave Plus devices.

• ZRX Yellow LED - If the light is blinking, then data is being received from Z-Wave Plus devices.

Z-Wave Terminology

Primary Controller: This is the main device used to set up and control your Z-Wave network. There can only be one

primary controller and it can be used to add or delete devices. A primary controller can be a portable device like a

hand-held remote, a static controller (permanently installed & never moved), a Z-Wave enabled PC or a Z-Wave enabled

Ethernet router/bridge.

Secondary Controller: The Z-Wave network supports multiple controllers so that additional Z-Wave remote controllers

can be used throughout the home. If the secondary controller is the same brand and model as the primary, it will have all

the same capabilities as the primary.

Home Control Network: The controllers and every Z-Wave device added with the primary controller are linked together

into a wireless network. Each device in the network has a unique address assigned to it and cannot be activated by a

neighbor’s Z-Wave controller.

Light/Node/Device: Node is the technical term used to describe a Z-Wave device in a home control network.

Please note that the terms “Node,” “Device,” and “Light” all refer to an individual Z-Wave enabled device and are

interchangeable within the context of these instructions.

Z-Wave Certiﬁcation

• The 738ZplusINT is a Z-Wave Security enabled device.

• The 738ZplusINT can be added to an existing network as a secondary controller using the Learn (LRN) process.

• The 738ZplusINT is compatible with Z-Wave devices from all manufacturers.

• The 738ZplusINT can perform a Factory Default Reset by initializing defaults in the panel programming menu.

• The 738ZplusINT only supports group one with a maximum of one node.

• The 738ZplusINT takes no action when a basic set command is received.

Initialize Defaults

Only use this procedure when the Z-Wave network primary controller is missing or otherwise inoperable. Follow these

steps to initialize Z-Wave programming:

1. Reset the panel.

2. Enter 2313 (DIAG) at a keypad and press CMD to access the panel DIAGNOSTIC MENU.

3. Press CMD until INIT Z-WAVE displays and press a top row select key or area.

4. Select YES when Z-WAVE? NO YES displays. INIT SUCCESSFUL displays when all Z-Wave programming has been

initialized.

COMPATIBILITY

XT30INT/XT50INT Series Panels

738ZplusINT modules connected to DMP XT30/XT50 Series panels with Version 171 ﬁrmware or higher provide

full Z-Wave Plus functionality. DMP XT30/XT50 Series panels with Version 125 or earlier provide standard Z-Wave

functionality.

XR150INT/XR550INT Series Panels

738ZplusINT modules connected to DMP XR150/XR550 Series panels with Version 182 ﬁrmware or higher provide

full Z-Wave Plus functionality. DMP XR150/XR550 Series panels with Version 181 or earlier provide standard Z-Wave

functionality.

Note: If you are upgrading ﬁrmware for an XT30/XT50 Series or an XR150/XR550 Series panel that is already

connected to a 738ZplusINT, you will need to initialize panel defaults to access Z-Wave Plus functionality. See the

appropriate panel Programming Guide for more information on initializing defaults.

Designed, engineered, and

manufactured in Springﬁeld, Missouri

using U.S. and global components.

INTRUSION • FIRE • ACCESS • NETWORKS

2500 North Partnership Boulevard

Springﬁeld, Missouri 65803-8877

800.641.4282 | DMP.com

Speciﬁcations

Power Requirements

Operating Voltage 8 to 14 VDC

Current Draw 40 mA

Frequency Range 868 MHz

Dimensions 4.5”W x 2.75”H x 1.75”D

Color White

Housing Material Flame retardant ABS

Certiﬁcations

Industry Canada: 5251A-PC0137R2

CE: EN 300 220/489

738ZplusINT Z-WAVE

INTERFACE MODULE

LT-1608INT 19345

Andere DMP Electronics Steuereinheit Handbücher

DMP Electronics

DMP Electronics Wiegand 734N Installationsanleitung

DMP Electronics

DMP Electronics 263EXT Bedienungsanleitung

DMP Electronics

DMP Electronics 734INT Installationsanleitung

DMP Electronics

DMP Electronics RoBoard RM-G144 Bedienungsanleitung

DMP Electronics

DMP Electronics 734 Installationsanleitung

DMP Electronics

DMP Electronics 734B Installationsanleitung

DMP Electronics

DMP Electronics 893A Bedienungsanleitung

DMP Electronics

DMP Electronics 780 Installationsanleitung

DMP Electronics

DMP Electronics 1116 Bedienungsanleitung

DMP Electronics

DMP Electronics SCS-104 Bedienungsanleitung

DMP Electronics

DMP Electronics 1134 Installationsanleitung

DMP Electronics

DMP Electronics 893A Bedienungsanleitung

DMP Electronics

DMP Electronics 734 Bedienungsanleitung

DMP Electronics

DMP Electronics Wiegand 734N Bedienungsanleitung

DMP Electronics

DMP Electronics 861 Bedienungsanleitung

DMP Electronics

DMP Electronics 734 Installationsanleitung

DMP Electronics

DMP Electronics 738Zplus Bedienungsanleitung

DMP Electronics

DMP Electronics Wiegand 734N Bedienungsanleitung

DMP Electronics

DMP Electronics 400 Bedienungsanleitung

DMP Electronics

DMP Electronics 734N-WIFI Administratorhandbuch

DMP Electronics

DMP Electronics 734 Installationsanleitung

DMP Electronics

DMP Electronics 717 Bedienungsanleitung

DMP Electronics

DMP Electronics ITI 738I Installationsanleitung

DMP Electronics

DMP Electronics 716 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung