DMP Electronics 1124 Bedienungsanleitung
INSTALLATION GUIDE
1124 360° PIR Motion Detector
Description
The 1124 PIR (Passive Infrared) Motion Detector is a wireless, four-element pyro intrusion detector for use with
DMP Wireless Receivers. The special hard lens offers wide coverage patterns even at low mounting heights, and is
especially immune to sunlight, halogen lights and uorescent lights.
The 1124 ceiling-mount PIR offers 360°/65.6 ft. diameter coverage when mounted on a 10 ft. high ceiling and
provides protection from intruders using a fully sealed sensor chamber. With a built-in tamper switch and selectable
high/low sensitivity the 1124 is very exible. For added convenience, the 1124 provides bidirectional temperature
compensation.
The 1124 PIR operates with the XR500 Series Command Processor™ panels using the 1100X Receiver or with the
XRSuper6, XR20, and XR40 Command Processor™ panels using the 1100D Receiver.
Features
• Wireless sensor with 360°/65.6 ft. coverage
pattern when installed at 10 ft. mounting
height
• Fully sealed sensor chamber with hard
spherical Lens
• Four-element Pyro sensor and sophisticated
signal processing
• Bidirectional temperature compensation
• Sensitivity adjustment and uorescent light
stability
What is Included
• One PIR detector with DMP wireless
transmitter
• One CR123A battery
• Zone name and number label
• Serial number label
Transmitter Serial Number
For your convenience, an additional pre-printed
serial number label is included. Prior to installing
the device, record the serial number or place the
pre-printed serial number label on the panel programming sheet. This number is required during programming. As
needed, use the zone name and number label to identify a specic transmitter.
Programming the PIR in the Panel
Refer to the XR500 Series Programming Guide (LT-0679) or
the XRSuper6/XR20/XR40 Programming Guide (LT-0305) as
needed. Program the device as a zone in Zone Information
during panel programming. At the Serial Number: prompt,
enter the eight-digit serial number, including leading zeros.
Continue to program the zone as directed in the panel
programming guide.
Note: When a receiver is installed, powered up, or the
panel is reset, the supervision time for transmitters is reset.
If the receiver has been powered down for more than one
hour, wireless transmitters may take up to an additional hour
to send a supervision message unless tripped, tampered,
or powered up. This operation extends battery life for
transmitters. A missing message may display on the keypad
until the transmitter sends a supervision
message.
Figure 1: 1124 PIR Exploded View
Sensor Mounting Base
Sensor Body
Sensor Cover
Transmitter
Board
Battery
Compartment
Pulse Width
Sensitivity Adjustment
Tamper
Alarm Test Button
Alarm Test LED
Transmitter LED
Mounting
Holes (4)
Serial Number
Label Location
Lock Screw
Silicon Gasket
Magnetic
Reed
Switch
RELAY
LR
EOL
–12V+
TAMPER
Lock
Screw
Sensor
Body
Sensor
Cover
Sensor
Mounting Base
Test
Magnet
Sensor Base
Alignment Dot
Sensor Base
Alignment
Arrow
Sensor Body
Alignment
Arrow
Phillips Head
Screwdriver
Figure 2: Remove Cover
Digital Monitoring Products 1124 PIR Installation Guide
2
1124 PIR Installation Guide Digital Monitoring Products
3
Selecting the Proper Transmission Location
(LED Survey Operation)
The PIR transmitter provides a survey capability to allow one
person to conrm transmitter communication with the
receiver while the cover is removed. Refer to Figure 2 to
remove the PIR cover. The PIR transmitter board Red Survey
LED turns on whenever data is sent to the receiver then
immediately turns off when the receiver acknowledgement
is received. Tripping the PIR tamper switch is a convenient
way to send data to the receiver to conrm operation. The
transmitter LED lights to indicate activity and to conrm
operation. See Figure 1 for LED locations.
When the transmitter does not receive an acknowledgement
from the receiver the LED remains on for about 8 seconds
to let you know communication is not established.
Communication is also faulty when the LED ashes multiple
times in quick succession. Relocate the transmitter or
receiver until the LED immediately turns off indicating
the transmitter and receiver are communicating properly.
Proper communication between the transmitter and receiver
is veried when for each press or release of the tamper switch, the LED
blinks immediately on and immediately off. Repeat this test to conrm ve
separate consecutive LED blinks. Any indication otherwise means proper
communication has not been established.
Mounting Location Considerations
Mount the unit:
• On a rigid vibration-free surface in a clean area
• So the expected intruder movement is across the detection pattern
elds, see Figures 4 and 5.
Do not locate the unit:
• Outdoors or in a place exposed to sudden temperature changes or
moisture
• In any area containing moving or vibrating objects
• In any ceiling tile containing an air vent
• Where it may be exposed to false alarm sources such as: direct sunlight,
heat sources (heater, radiators, etc.) in the eld of view or strong air drafts (fans, air conditioner, etc.)
Setting the Sensitivity Jumper
Use the jumper located on the sensor unit PCB to set the sensitivity, as shown
in Figure 3. Use the following to determine the appropriate jumper settings
for an application.
Pulse Width Sensitivity Adjustment
Position 1 (right two pins) is for normal operating conditions and operation. Set
the jumper on the two right pins of the 3-pin jumper closest to the number 1.
Position AUTO (left two pins) is used for harsh environment locations with
air drafts. Set the jumper on the two left pins of the 3-pin jumper below the
word AUTO.
Unit Testing
There are three ways to activate the walk and alarm transmission tests to
check PIR range and verify signals. Before performing any of the tests,
ensure the 1124 PIR is currently programmed in the Command Processor™
panel. Refer to Figures 2 and 3 as needed.
1. Using a magnet placed close to the sensor cover opposite the lock screw.
OR
2. Remove the cover and press the internal test button. OR
3. External push button connected to the two terminals marked EXT. TEST. When testing is complete disconnect
the external push button wires and replace the sensor cover.
Figure 4: Detection Pattern
Ceiling
10 ft. high
(3m)
46 ft. (14 m)
2.6 ft.
(0.8 m)
Effective
Detection
Diameter
Floor
65 ft. (20 m)
PIR Pattern
0 (0)
32.8 21.6 10.8 0 10.8 21.6 32.8 ft.
(10) (6.6) (3.3) (0) (3.3) (6.6) (10) (m)
Top View
Side View
ft. (m)
65.6 ft. (20m)
8 (2.4)
10 (3)
12 (3.6)
Figure 5: Lens Pattern
Figure 3: 1124 PIR Circuit Layout
Battery
Compartment
Pulse Width
Sensitivity
Adjustment
Alarm Test LED
Magnet Reed Switch
for Testing
Pushbutton for
Alarm Testing
1124 External
Test Option
Tamper
Transmitter LED
Transmitter
PCB
Serial
Number
Label
Location
Digital Monitoring Products 1124 PIR Installation Guide
2
1124 PIR Installation Guide Digital Monitoring Products
3
Walk Test
During the Walk Test the installer walks around the room where the PIR is installed to detect the PIR coverage. See
Figures 4 and 5.
1. Initiate the selected test operation using the magnet, pressing the internal test button or external push button
for less than one second.
2. This activates the device for one minute to enable the Walk Test.
3. Walk test the unit to verify the PIR coverage. Refer to Selecting the Proper Transmission Location (LED Survey
Operation) as needed.
Alarm Transmission Test
1. Press the internal test button or external push button for at least two seconds. This immediately activates the
alarm transmission.
2. To check this function, verify that the keypad display indicates a signal received from the detector. The
detector sends 11 transmissions to the control panel during the one minute test period.
Tamper Transmission Test
1. Remove the sensor cover to fault the tamper and initiate a tamper trouble message.
2. Verify that the keypad display indicates a trouble or alarm message.
Mounting the Unit
Caution: You must be free of static electricity before handling sensor circuit boards. Touch a grounded,
bare metal surface before touching circuit boards or wear a grounding strap.
Prior to permanently mounting the 1124 PIR, check that the PIR and control panel communication is working. See
the Unit Testing section. As needed refer to Figures 1 and 2.
1. Use a Phillips head screwdriver to unscrew the lock screw at the edge of the 1124 case.
2. Hold the bracket mounting base in one hand and the sensor cover in the other hand. Turn the sensor cover
counterclockwise to unlatch it from the base and remove the cover.
3. Hold the bracket mounting base in one hand and the sensor body in the other hand. Turn the sensor body
counterclockwise to unlatch it from the base and separate the body from the mounting base.
4. Mark and drill the ceiling mounting holes. Use screws and anchors, if necessary, to mount the detector base to
the ceiling.
5. Line up the sensor body alignment arrow with the base alignment dot. Turn the sensor body clockwise to line
up the sensor body alignment arrow up to the base alignment arrow and latch the body into place. Do not
overtighten.
6. Install the battery. See Installing or Replacing Batteries later in this document.
7. Place the sensor cover into the slots in the sensor body and turn the sensor cover clockwise to latch it into
place.
8. Set the lock screw in place and use a Phillips head screwdriver to tighten it down.
Installing or Replacing Batteries
Note: If the battery reaches the factory preset low level, a Low Battery signal is sent to the panel. The 1124 PIR
remains operational for approximately 30 days to allow adequate time to replace the battery.
Observe polarity when installing the battery. Use only 3.0V lithium batteries, DMP Model CR123A, or the equivalent
battery from a local retail outlet.
Note: When setting up a wireless system, it is recommended to program zones and connect the receiver before
installing batteries in the transmitters.
1. If installed, remove the sensor cover. See Figure 2.
2. If replacing the battery, remove the battery before installing a new battery.
3. Observe polarity and insert the 3.0V Lithium battery into the battery holder where indicated in Figures 1 and 3.
Caution: Risk of re, explosion, and burns. Do not recharge, disassemble, heat above 212°F (100°C), or
incinerate. Properly dispose of unused batteries.
LT-0704 (9/06) © 2006 Digital Monitoring Products, Inc.
800-641-4282
www.dmp.com
Made in the USA
INTRUSION • FIRE • ACCESS • NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
Battery Life Expectancy
Typical battery life expectancy for DMP Model 1124 wireless PIR is three years. DMP wireless equipment uses
two-way communication to extend battery life.
The following situations can reduce battery life expectancy:
• If a receiver is unplugged, does not return a signal, or is not installed.
• Frequent transmissions, such as constant motion where messages are sent every time the movement is
detected.
• When installed in extreme hot or cold environments.
Note: Transmitters continue to send supervision messages until a receiver returns an acknowledgement.
After an hour the transmitter only attempts a supervision message every 60 minutes.
Note: To compensate for frequent motion, after motion is detected with no activation and a message sent the
1124 PIR automatically rests until no motion is detected for two minutes. After two minutes of no activity, the
1124 PIR is ready to respond to any new motion detected. Because of this operation, do not program a wireless
PIR for cross zone operation unless other zones are also programmed to provide cross zone operation.
The following situation can extend battery life expectancy:
• Extend transmitter supervision time in panel programming.
• Infrequent transmission trips, such as a low trafc area where messages are rarely sent.
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modications made by the user and not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specications
Battery
Life Expectancy 3 years (normal operation)
Type 3.0V Lithium CR123A
See Battery Life Expectancy for details.
Transmit condition Alarm, Test, Supervision,
Low Battery
Detection
Range 360°/65 feet diameter
Speed 1-5 feet/second
Mounting height up to 10 feet
Dimensions 5.2” W X 2.25” H
Color White
Patents
Patent(s) Pending
Listings and Approvals
FCC Part 15 Registration ID CCKPC0088
Andere DMP Electronics Sicherheitssensor Handbücher
DMP Electronics
DMP Electronics 1128 Bedienungsanleitung
DMP Electronics
DMP Electronics 1126 Series Montageanleitung
DMP Electronics
DMP Electronics XT30INT Bedienungsanleitung
DMP Electronics
DMP Electronics 1121 Montageanleitung
DMP Electronics
DMP Electronics 1122INT Bedienungsanleitung
DMP Electronics
DMP Electronics 1184 Bedienungsanleitung
DMP Electronics
DMP Electronics 1135INT Series Bedienungsanleitung
DMP Electronics
DMP Electronics 1183-135F Bedienungsanleitung
DMP Electronics
DMP Electronics 1127W-WINT Montageanleitung
DMP Electronics
DMP Electronics 1161 Bedienungsanleitung
DMP Electronics
DMP Electronics XTLtouch International Series Bedienungsanleitung
DMP Electronics
DMP Electronics 1126R Bedienungsanleitung
DMP Electronics
DMP Electronics 1128 Bedienungsanleitung
DMP Electronics
DMP Electronics 1168 Installationsanleitung
DMP Electronics
DMP Electronics XR Series Bedienungsanleitung
DMP Electronics
DMP Electronics 1129 WIRELESS GLASSBREAK DETECTOR Bedienungsanleitung
DMP Electronics
DMP Electronics DEL AOP PRO 50 Bedienungsanleitung
DMP Electronics
DMP Electronics 1128INT Bedienungsanleitung
DMP Electronics
DMP Electronics 1121-WINT PIR Montageanleitung
DMP Electronics
DMP Electronics SR3 Bedienungsanleitung
