Dometic PCD5501 Bedienungsanleitung

WARNING

Cancer and Reproductive Harm

www.P65Warnings.ca.gov

POWER AND CONTROLS

CONTROL

Dometic Interact

Installation Manual . . . . . . . . . . . . . . . . . . . 2

Contents Dometic Interact

2EN

Service Center & Dealer Locations

Visit: www.dometic.com

Read these instructions carefully. These instructions MUST stay with this product.

Contents

1 Explanation of Symbols

and Safety Instructions . . . . . . . . . . . . . . . . . . . .3

1.1 Recognize Safety Information . . . . . . . . . . . . . . .3

1.2 Understand Signal Words . . . . . . . . . . . . . . . . . .3

1.3 Supplemental Directives . . . . . . . . . . . . . . . . . . .3

1.4 General Safety Messages . . . . . . . . . . . . . . . . . .3

2 General Information. . . . . . . . . . . . . . . . . . . . . . .3

2.1 Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2.2 Required Tools and Equipment. . . . . . . . . . . . . .4

2.3 Component Overviews . . . . . . . . . . . . . . . . . . . .4

2.3.1 PCD5501 LCD Display . . . . . . . . . . . . . .5

2.3.2 DB-100 DC Distribution Board . . . . . . . .5

2.3.3 DB-201 H-Bridge Driver Board . . . . . . . .5

2.3.4 LR-125 Wi-Fi Server Module . . . . . . . . . .6

2.3.5 TM-502A Inverter Interface. . . . . . . . . . .6

2.3.6 TM-2021 HVAC Load Box. . . . . . . . . . . .6

2.3.7 TM-180 Tank Dump. . . . . . . . . . . . . . . . .7

2.3.8 SeeLevel II Tank Monitor . . . . . . . . . . . . .7

2.4 RVC Communications Network Overview . . . . .7

2.4.1 RVC Distribution Boards . . . . . . . . . . . . .8

2.4.2 RVC Load Boxes . . . . . . . . . . . . . . . . . . .9

3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

3.1 Setting Up the Power Supply. . . . . . . . . . . . . . . 9

3.2 Installing the Distribution Board . . . . . . . . . . . .10

3.3 Installing the DB-100 . . . . . . . . . . . . . . . . . . . . . 11

3.4 Installing the DB-201 . . . . . . . . . . . . . . . . . . . . .12

3.5 Installing the Inverter . . . . . . . . . . . . . . . . . . . . .13

3.6 Installing the TM-2021 HVAC Load Box . . . . . .14

3.7 Installing the TM-180 . . . . . . . . . . . . . . . . . . . . .15

3.8 Installing the SeeLevel II . . . . . . . . . . . . . . . . . . .16

3.9 Installing the Touch-screen Display . . . . . . . . . .17

4 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.1 OmniScope Overview . . . . . . . . . . . . . . . . . . . .17

4.2 OmniScope Connection and Use . . . . . . . . . . .18

5 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.1 Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . .18

5.2 Preventive Maintenance. . . . . . . . . . . . . . . . . . .18

6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 19

7 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

LIMITED ONE-YEAR WARRANTY. . . . . . . . . . . . . . 21

Dometic Interact Explanation of Symbols and Safety Instructions

1 Explanation of Symbols

and Safety Instructions

This manual has safety information and instructions to

help you eliminate or reduce the risk of accidents and

injuries.

1.1 Recognize Safety Information

1.2 Understand Signal Words

A safety symbol and/or signal word identify safety

messages and indicate the hazard severity.

NOTICE: Used to address practices not related to

physical injury.

1.3 Supplemental Directives

To reduce the risk of accidents and injuries, please

observe the following directives before proceeding to

operate this appliance:

• Read and follow all safety information and instructions.

• Read and understand these instructions before

operating this product.

• The installation must comply with all applicable local or

national codes, including the latest edition of the

following standards:

U.S.A.

– ANSI/NFPA70, National Electrical Code (NEC)

– ANSI/NFPA 1192, Recreational Vehicles Code

– ANSI Z21.57, Recreational Vehicles Code

Canada

– CSA C22.1, Parts l & ll, Canadian Electrical Code

– CSA Z240 RV Series, Recreational Vehicles

1.4 General Safety Messages

• Use only Dometic replacement parts and components

that are specifically approved for use with the

appliance.

• Use care when diagnosing and/or adjusting

components on a powered unit.

• Do not modify this product in any way. Modifications

can be extremely hazardous.

• Do not allow children to play with this product or with

fixed controls (if applicable).

2 General Information

Dometic Interact (DI) provides a central control and

monitoring hub for the appliances in your recreational

vehicle (RV). DI allows all of the liquid crystal displays

(LCDs) in the RV to communicate continuously with each

other over the RV communications (RVC) bus, so that

when one LCD is down, the others can continue to

operate. The system has a mobile application control

option.

DThis is the safety alert symbol.

It is used to alert you to potential physical injury

hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DDANGER!

Indicates a hazardous situation that, if not avoided,

will result in death or serious injury.

!WARNING:

Indicates a hazardous situation that, if not avoided,

could result in death or serious injury.

!CAUTION:

Indicates a hazardous situation that, if not avoided,

could result in minor or moderate injury.

IIndicates additional information that is not related to

physical injury.

!WARNING: FIRE, IMPACT, AND/OR

EXPLOSION HAZARD.

Failure to obey the following warnings could result in

death or serious injury:

IThe images used in this document are for reference

purposes only. Components and component

locations may vary according to specific product

models. Measurements may vary ±0.38 in. (10 mm).

General Information Dometic Interact

4EN

This section describes the intended use of the product,

the tools and equipment required for the installation of

the product, the system components, and how the RVC

communications network functions.

2.1 Intended Use

Dometic Interact is intended to be used in conjunction

with the existing control and/or monitoring devices

within your RV. It does not replace the actual hardware

controllers for the systems within the RV. It is a display that

sends action signals and commands to various

components (such as load boxes).

The manufacturer accepts no liability for damage in the

following cases:

• Faulty assembly or connection

• Damage to the product resulting from mechanical

influences and excess voltage

• Alterations to the product without express permission

from the manufacturer

• Use for purposes other than those described in the

operating manual

Dometic Corporation reserves the right to modify

appearances and specifications without notice.

2.2 Required Tools and Equipment

The following tables outline the tools and equipment

required for the installation of this system.

2.3 Component Overviews

This section describes the available components for use

with Dometic Interact. Each component used must be

chosen based on the onboard devices that will be

connected to the system and controlled from the

Dometic Interact LCD display. Distribution boards must

be chosen based on the installation method.

Hardware and Tools

Wire Strippers

Molex Terminal Pin Crimpers

JST Terminal Pin Crimpers

Spade Terminal Crimpers

Small Philips-head Screwdriver

Harnesses and Cables

18–22 AWG Wires for the 4-Wire RVC Harnesses

22–24 AWG Wires for the 4-Wire LCD Harnesses

14–18 AWG for Wiring the Loads Through Relays

RJ-11 and RJ-12 6-Conductor Cables for the Air Conditioner

(AC) and Fan

Connectors

5557 Series Molex Connectors: 12-pin 39-01-2120, 6-pin

39-01-2060, and 4-pin 39-01-2040

Pins for Molex Connectors: 39-00-0039

LCD Display Connector: PAP-05V-S (JST terminals)

Pins LCD Connector: 455-1325-1-ND, Mf #: SPHD-001T-P0.5

Spade Terminals for DB-100, DB-200, and MS-733 Outputs

Ring Terminal: 10–12 AWG

WAGO Connectors or Wire Connectors

IInstallations and component requirements will vary

according to available onboard appliances and

Original Equipment Manufacturer (OEM)

requirements. Therefore, the components

outlined in this section may or may not be used.

Refer to the custom installation instructions

provided for your specific setup.

Dometic Interact General Information

2.3.1 PCD5501 LCD Display

1 PCD5501 LCD Multiple-Screen Interface

2 PCD5501 LCD Single-Screen Interface

The 3.5 in. (89 mm) touch-screen display provides

convenient access to the Dometic Interact system, and

allows users to access, view, and control all connected

devices. It is available in single- or multiple-screen

interfaces and provides:

• One-touch control for user-programmable modes,

such as Home, Away, and Sleep

• Haptic touch and sound feedback

• Control and monitoring of the RV’s vital and

convenience features

2.3.2 DB-100 DC Distribution Board

3 DB-100 DC Distribution Board

The DB-100 distribution board has one 12 VDC input pin

and one 12-pin connector, located on the side, for power

and RVC communications.

There are ten relay outputs, the first five are capable of

handling 10 A on each pin and the next five pins are

capable of handling 5 A on each pin. The load box can

handle up to 75 A total, with 12 VDC on each output. The

outputs are open drain, so the off state is open.

The DB-100 distribution board monitors/controls the

following devices/functions, but are not limited to:

• Lights

• Water pump

• Awnings

• Satellite dish

2.3.3 DB-201 H-Bridge Driver Board

4 DB-201 H-Bridge Driver Board

General Information Dometic Interact

6EN

The DB-201 driver board uses H-bridge outputs. They are

typically in a pair, but you can use two individual outputs

on each pair. The off state for the DB-201 outputs are

ground.

The DB-201 driver board controls/monitors the following

devices/functions, but are not limited to:

• Lights

• Locks

• Slide-outs

• Generator

• Parking brake

• Ignition

2.3.4 LR-125 Wi-Fi Server Module

5 LR-125 Wi-Fi Server Module

The LR-125 is the onboard Wi-Fi server. It must be

connected to the main power supply and the RVC

network bus as outlined in the schematics.

The changes from the 3.5 in. (89 mm) displays are

updated to and from the LR-125 application. The time on

the clock screen updates based on the LR-125

communication through the RVC network.

2.3.5 TM-502A Inverter Interface

6 TM-502A Inverter Interface

The TM-502A inverter interface is used for a Magnum

inverter (MMS1012) that is not RVC compatible.

2.3.6 TM-2021 HVAC Load Box

7 TM-2021 HVAC Load Box

The TM-2021 load box is the interface module that

controls the HVAC appliances.

The TM-2021 controls/monitors the following devices/

functions:

• Temperature sensor

• Battery

• Pump

• Fans

• Furnace

• AC

IUsers can gain system control through this module

via the mobile application. Refer to the Dometic

Interact Operation Manual for more information.

IAn RVC compatible inverter, such as a Xantrex, can

be connected directly to the RVC network/bus

without the need for the TM-502A module.

IThere are no outputs on this module for battery-

powered lights, awnings, or slide-outs.

Dometic Interact General Information

2.3.7 TM-180 Tank Dump

8 TM-180 Tank Dumps

The TM-180 module supports the following functions:

•Dump Valve Control: This allows manual control of

two waste dump valves, automatic dumping when a

tank level reaches a programmed level, or automatic

dumping when the valves automatically close due to

an empty tank.

•Valve Interlocks: Valves automatically close upon

vehicle movement. Only one valve will be open at a

time. If an automatic command to dump a tank is

received when the other tank is open, it is queued for

later processing. If a manual command is received, the

other valve is closed first.

•Sanicon: The Sanicon can run while either waste valve

is open. It continues to run for a programmed length of

time after closing the valve. While the dump valves

have an indicator circuit to indicate when they are

closed, the TM-180 hardware does not have the ability

to read this input. The unit always closes the valves on

startup, and then keeps track of the valve status

internally from there.

•Additive Pump: The TM-180 module supports an

additive pump. The additive is supplied in proportion

to the amount of waste in the black tank, disbursed in

increments of configurable size. The module also

supports a reservoir empty sensor.

2.3.8 SeeLevel II Tank Monitor

9 SeeLevel II Tank Monitor

The SeeLevel II interface module monitors the battery

level, as well as the fresh, gray, and black water tanks.

Some models also monitor LPG gas levels.

2.4 RVC Communications Network

Overview

RVC is a controlled area network (CAN)-based

communication profile for RVs. It was developed by the

Recreation Vehicle Industry Association (RVIA).

The Dometic Interact system of devices uses RVC data

networking, utilizing a twisted pair of wires terminated at

each end of the network with 120-Ohm resistors.

Terminating resistors are also populated on the

distribution boards.

Refer to “RVC Distribution Boards” on page 8 for

choosing the right distribution board for your application.

Every device on the network digitally transmits the RV

systems data via the RVC data pair, which is distributed by

the distribution boards and harnesses.

IYou can connect only one fresh water, one gray

water, and one black water tank to the module,

with one sensor each.

IYou can combine two sensor strips together for

taller tanks. Refer to the Garnet manual for sensor

integration information.

General Information Dometic Interact

8EN

Here is an example of a typical wireframe RVC

communication network:

10 Typical Wireframe RV Communication Network

2.4.1 RVC Distribution Boards

The RVC distribution boards used with this system enable

central distribution points for communication and power

for all the devices. They can be 3-way, 6-way, or 12-way,

both with and without terminating resistors (which are

installed on the boards themselves).

This provides a simple way to increase the network size

while allowing for flexibility in locating devices.

Make sure to choose a distribution board with 120 ohm

resistors on both ends of the bus. If you look at the

drawing below, the distribution board in the middle does

not need a 120 ohm resistor.

Here are some examples of the distribution boards,

which are chosen based on the OEM installation

requirements:

11 Example Distribution Boards

Dometic Interact Installation

2.4.2 RVC Load Boxes

The RVC load boxes used in this system act as the drivers

that control the appliances, interfacing between all

onboard appliances, such as lights, fans, AC units,

furnaces, awnings, and slide-outs.

The load box type chosen is based on the load type, as

per the OEM requirements.

3 Installation

This section provides general installation information for

the components that can be used with the Dometic

Interact system. Refer to “Component Overviews” for

more information about the compatible components and

the devices that they control.

Ensure that you have the following experience and

knowledge before attempting to install the Dometic

Interact system:

• Experience with electrical wiring

• Knowledge of onboard appliances (Dometic or others)

• Understanding of electrical drawings

• Basic understanding of RVC/CAN networks

• Experience with manufacturing/repairing RVs

• Completed Dometic Interact Product Overview online

or class training

3.1 Setting Up the Power Supply

To operate properly, the Dometic Interact system must

receive power from the shore, a generator, or another

alternative source.

Both shore and generator power supplies should be

wired to the automatic transfer switch so that it allows only

one power-out line. The 120 VAC power from the switch

is fed to the inverter input terminal. The 12 VDC rectified

power then charges the RV battery.

When there is no shore or generator power present, the

inverter changes the DC power to AC and feeds it to the

outlets from the inverter AC output terminal. For inverter

wiring information, refer to the inverter installation and/or

operation manual.

When shore or generator power is present, the inverter

receives the AC voltage and generates the AC output

while bypassing the inverting process. It also charges the

battery in parallel. Refer to Fig. 15 on page 13.

If you have other renewable resources of energy, like

solar panels, you can directly charge the RV battery. Send

the energy collected from the solar panels to the charger

controller first. The 12 VDC power from the charger

controller then charges the RV battery and monitors the

battery level so that it does not become overcharged.

!WARNING: ELECTRICAL SHOCK, FIRE, AND/

OR EXPLOSION HAZARD.

Use care when installing components onto a

powered RV system. Failure to obey this warning

could result in death or serious injury.

IDue to the nature of the product and the variations

of onboard appliances, each installation comes

with a customized set of installation instructions. All

wiring diagrams included in this section are

provided for example purposes only. Detailed

wiring diagrams and installation schematics are

provided with the custom installation instructions

for your specific setup.

IA current RVIA certification for technicians is not

required, but it is helpful.

IFor more details, refer to the manual provided with

the solar panels.

Installation Dometic Interact

10 EN

3.2 Installing the Distribution Board

The diagram below shows one possible configuration of

the system components installed on the distribution

board.

12 System Configuration Example

The diagram above shows one possible configuration of

the system components installed on the distribution

board. Connect the RVC devices in any sequence.

Use any length of connection between the distribution

boards, but the length of the twisted pair wires between

a distribution board and a device should be less than 6 ft

(183 cm) in order to gain the proper RVC communication.

Pin Designation

12VDC

GROUND

RVC -

RVC +

Communication

GROUND

Distribution Board Plugs

Communication

Input /Out put (Type)

12VDC

GREY

DIAGNOSTIC PLUG

All Connections Are

Wire Si de View

BATT FRESH BLACK LPG

120 Ohm

MADE IN CANA DA

GARNET INSTRUMENTS LTD.

LEVEL IN PERCENT

SEELEVEL II TANK MONITOR

All Connections Are

Wir e Side View

654321

12 11

10 2 14635879

12 111416 131518 1720 19

All Connections Are Wire Side View

All Connections Are

Wir e Side View

Xantrex Freedom XC Pro 2000

CIRCUITSCIRCUITS

120 Ohm

Input/Output (Type)

Input

FUSED 12VDC FROM DC PANEL

Designat ion

12VDC

GROUND

DC Distribution Board

DB100

S/W Version V1.25

1 2 3 4 5 6 7 8 9 10

12V

Outputs Outputs

H- Bridge

Driver Board

DB200

S/W Version v1.18

Outputs

Climate Control Module

TM-2021

S/W Version v1.30

Wi-Fi Server Module

LR125

S/W Version v1.10

Outputs

3.5" Display

IRefer to RVC Communications Network Overview

for more information.

Andere Handbücher für PCD5501

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dometic Controller Handbücher

Dometic

Dometic Go Power! GP-SB-PWM-30BT Bedienungsanleitung

Dometic

Dometic Go Power! GP-RVC-R Bedienungsanleitung

Dometic

Dometic Go Power! GP-SB-PWM-10 Bedienungsanleitung

Dometic

Dometic Go Power! DURALITE 100 Bedienungsanleitung

Dometic

Dometic DTD01A Bedienungsanleitung

Dometic

Dometic EA1000 Bedienungsanleitung

Dometic

Dometic SC330 Bedienungsanleitung

Dometic

Dometic Optimus Adaptive Trim Tab System Benutzerhandbuch

Dometic

Dometic GP-PWM-10-FM Bedienungsanleitung

Dometic

Dometic 9600023541 Bedienungsanleitung

Dometic

Dometic GP-MPPT-60/10 Bedienungsanleitung

Dometic

Dometic Go Power! 30 AMP RVC MPPT Bedienungsanleitung

Dometic

Dometic Go Power GP-PWM-10-SQ Bedienungsanleitung

Dometic

Dometic Go Power! GP-PC Series Bedienungsanleitung

Dometic

Dometic Optimus Adaptive Trim Tab System Bedienungsanleitung

Dometic

Dometic Go Power! GP-SB-PWM-10 Bedienungsanleitung

Dometic

Dometic GP-MPPT-60/10 Bedienungsanleitung

Dometic

Dometic SC330 Betriebsanleitung

Dometic

Dometic PCWM-VAR Bedienungsanleitung

Dometic

Dometic Zamp Solar ZS-30A Deluxe Bedienungsanleitung

Dometic

Dometic TankManager Bedienungsanleitung

Dometic

Dometic RTX1000 Bedienungsanleitung

Dometic

Dometic Go Power! GP-PWM-30-SB Bedienungsanleitung

Dometic

Dometic Go Power GP-PWM-10-SQ Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch