Dometic RH 423LDAG Bedienungsanleitung

207.5396.43

RH 423LDAG RH 439LDAG

Type: MB20-60

miniBar

Operating Instructions

Bedienungsanleitung

Mode d'emploi

Istruzioni per l'uso

Handleiding

Manual de Instrucciones

Instruções de Utilização

Thank you for choosing our appliance. We are sure it will provide you with trouble-free use.

In the following, we would like to familiarise you with some symbols, which we bring to your attention to ensure

the safe and efficient operation of the appliance:

source of danger, in event of improper operation

suggested useful tips to read

information concerning environmental protection

This refrigerator is intended for the storage of food and drinks.

Attention!

This product is designed to be operated by adults. Children should not be

allowed to tamper with the controls or play with the product.

Any electrical work required to install this appliance should be carried out by a

qualified electrician.

This product should be serviced by an authorised Service Engineer, and only

genuine spare parts should be used.

It is dangerous to alter the specifications or modify this product in any way.

Care must be taken to ensure that the appliance does not stand on the

electrical supply cable.

There are working parts in this product which heat up. Always ensure that there

is adequate ventilation as a failure to do this will result in component failure and

possible content loss. See installation instructions.

Parts which heat up should not be exposed. Wherever possible the back of the

product should be close to a wall but leaving the required distance for

ventilation as stated in the installation instructions.

Before defrosting, cleaning or maintenance work is carried out, be sure to

switch off the appliance and unplug it.

DO NOT USE SHARP INSTRUMENTS to scrape off frost or ice. Under no

circumstances should solid ice be forced off the cooling plate. Solid ice should

be allowed to thaw when defrosting the appliance. See defrost instructions.

This appliance is heavy. Care should be taken when moving it.

Under no circumstances should you attempt to repair the appliance yourself.

Repairs carried out by inexperienced persons may cause injury or more serious

malfunctioning. Refer to your local Service Centre and always insist on genuine

spare parts.

In this appliance the storage of any toxic or explosive substance is forbidden!

Please read these operating instructions carefully before putting the

refrigeration unit into operation. If you later sell or dispose of it, please ensure

that the new owner receives these operating instructions.

Please follow the installation details below carefully. Guarantee is valid for

products installed as described only. (See chapter 4.1.)

Attention!

Warranty arrangements are in accordance with EC Directive 44/1999/CE and

the normal conditions applicable in the country concerned.

For warranty or other servicing, such as spare-parts, please contact our Dometic

Service Network.

The warranty does not cover any damage due to improper use.

The warranty does not cover any modifications to the appliance or the use of

non-original Dometic spare-parts.

The warranty does not apply if the installing and operating instructions are not

adhered to.

When contacting Dometic Service Network, please state the model, product

number and serial number. You will find this information on the data plate inside

of the refrigerator.

CONTENTS

1. Unpacking

2. View of the appliance

3. Cleaning

4. Positioning the appliance

4.1. Installation instruction

5. Using the appliance

5.1. Initial operation

5.2. Temperature regulation

5.3. Cooling unit control (CUC)

6. Ice cubes

7. Useful suggestions

8. Defrosting, cleaning and maintenance

8.1. Automatic defrost function

8.2. Interior light

8.3. Automatic Door Control LED (ADC) optional

9. Reversing the door hang

10. Customer service

11. Putting into operation, technical data

11.1. Connecting to electrical mains

12. Environmental protection information

13. Recycling

1. Unpacking

After removal from the cardboard packaging, make

sure the appliance is not damaged. If you find damage

to the appliance resulting from transport, report it

immediately to the transportation firm.

2. View of the appliance

1. Door

2. Door lock (if available)

3. Ice tray

4. Lamp

5. Evaporator cover

6. Evaporator sensor (behind evaporator)

7. Evaporator

8. Shelves

9. Air sensor

10. Foot

11. ADC LED (if available)

12. Cowl

RH 423 LDAG

IN CASE IF YOUR REFRIGERATOR IS EQUIPPED WITH LOCK, DOMETIC ZRT DO NOT ACCEPT

LIABILITY FOR LOSS OR DAMAGE OF KEYS. HOWEVER A COMPLETE LOCK CAN BE SUPPLIED.

RH 439 LDAG

Figure 1.

3. Cleaning

Clean the refrigerator thoroughly at intervals, as

necessary. Remove the shelves; these, parts,

as well as the cabinet interior and the door should be

washed with a warm solution of sodium bi-carbonate.

Finally wipe over with a cloth rinsed in warm water

only, and dry with a clean cloth. Do not wash any

plastic parts in water that is more than hand warm, and

do not expose them to dry heat. The outside of the

cabinet should be wiped down regularly with a clean,

damp cloth.

NEVER USE STRONG CHEMICALS OR ABRASIVE

CLEANING MATERIALS ON ANY PART OF THE

CABINET.

4. Positioning the appliance

When first using this refrigerator please consider the

following points:

ENSURE REFRIGERATOR IS LEVEL

THE PIPEWORK AT THE BACK GETS HOT IN USE

THE REFRIGERATOR HAS NO 'MOTOR' AND IS

THEREFORE VIRTUALLY SILENT

ALLOW AT LEAST 3 HRS. FOR SIGNS OF

COOLING

During the refrigeration process, the appliance

gives off heat from the condenser (under the

upper part of the rear cover) into the surrounding air.

The more ventilated the condenser is, the more

effective the refrigeration will be.

The other condition for satisfactory operation is that

the appliance is levelled. This could be checked by

placing a glass of water on top of the appliance.

It is important that the appliance is not directly

exposed to radiated heat (sunlight, radiator, near an

oven, etc.).

4.1. Installation instructions

The refrigerator is equipped with an electrically heated

absorption cooling unit which is virtually silent in

operation. The fridge is designed for free-standing

installation, but can be built-in if the following

conditions are complied with to ensure satisfactory

operation and maximum cooling efficiency.

The miniBar can be screwed to the furniture using the

fittings at the bottom. Drive in the screws (figure 2).

At the building-in process please take into

consideration the items listed below.

Figure 2.

IMPORTANT

Please follow the installation details below

carefully. Guarantee is valid for products

installed as described only.

1. The refrigerator must be level both

directions

2. There should be 20 mm clearance to the wall

3. Ventilation must be provided as shown in

alternatives A, B, C or D (fig. 3-4)

Figure 3.

4. The ventilation duct must at least measure

105 mm x the width of the refrigerator

5. Only the entire cooling unit must project into

the duct as shown

6. Air passing through the duct must not be

preheated by any source of heat

7. Ventilation grills, if used, must have an free

openings of at least 200 cm²each

miniCool

Air in

Air out

Ventilation grille

Air out

Air in

miniCool

miniBar

Figure 4.

During installation, please ensure the

mains plug is accessible at all times.

5. Using the appliance

To start the refrigerator connect the plug to the socket

outlet. The empty refrigerator needs about 6-7 hours

at normal ambient temperature to reach the proper

temperature in the storage compartment.

5.1. Initial operation

The device must be plugged into a properly earthed

socket.

The miniBar starts automatically with a self-test. If

the electronics do not detect any fault, the

refrigerator starts to cool down. If a fault is

detected, the refrigerator stops cooling. If this

occurs, please consult your authorised Customer

Service.

5.2. Temperature regulation

The miniBar is fitted with a fully automatic electronic

temperature regulator. It is not needed to set the

temperature of the storage compartment manually.

5.3. Cooling unit control (CUC)

The electronic checks the function after every

defrosting period (every 24 hours) by measuring the

evaporator temperature drop. If it registers a problem

the refrigerator will shut down and stops cooling. If this

happens you should check whether the refrigerator

has been overloaded, that the door was properly

closed, that the cooling unit ventilation is correct and

that the refrigerator is levelled. After checking, unplug

the refrigerator at least for 10 seconds and plug in

again. This resets the unit and it will function again. If

no sign of cooling there is a problem and you should

then contact Dometic service.

miniCool

min. 60 mm

Ventilation grille

Air in

miniCool

Air in

Air out

6. Ice cubes

Fill the ice tray up to 4/5 with drinking water, cover

with the lid and place the closed ice tray on the ice-

tray shelf. Wipe off any excess water to prevent the

ice tray from freezing to the surface.

To remove the cubes from the ice tray, hold it under

running water. Remove the lid with the ice cubes

from the ice tray and the ice cubes can now be

taken out easily.

7. Useful suggestion

Do not overfill the appliance. If possible, always

store pre-cooled food and/or drinks. It is advisable

to leave some space between the products in the

cabinet to ensure efficient and even cooling. If the

shelves are packed too tightly there may be

unacceptable temperature variations.

8. Defrosting, cleaning and

maintenance

Frost will gradually form on the cooling plate and it

must not be allowed to become too thick since it

restricts the cooling.

This miniBar is fitted with a fully automatic

electronic temperature regulator.

The frost will melt and the defrost water will run

through the drain tube from the drip channel into an

evaporating vessel located at the bottom rear of the

refrigerator. (Fig. 5) The defrost water will evaporate

automatically into the circulating air and the vessel

will not need emptying.

Figure 5.

To switch off the unit, disconnect the refrigerator

from the electricity supply and leave the cabinet

door open. After defrosting the cabinet interior

should be wiped out with a clean, damp cloth.

8.1. Automatic defrost function

The first defrosting phase commences 39 hours

after the start and lasts for two hours.

After this, the device operates for 22 hours at a

time, followed by a defrosting period of 2 hours.

miniBar

8.2. Interior light (fig. 6.)

Two light-emitting diodes (A) on an electronic PCB

illuminate the cooling compartment when the door is

opened.

Two sensors (B) control whether the door is open or

not and the LEDs and the door control as well will

work accordingly.

Figure 6.

8.3. Automatic Door Control LED (ADC)

(optional)

The LED (Fig. 7.A) mounted to the screw down foot

lower door hinge indicated whether the miniBar door

has been opened. If so then:

1. Open the miniBar, check the content in the

compartement and if necessary, replenish.

2.Reset the door control signal by helding the

Remote control against the door opening sensor

(Fig. 6. B) and push the button.

3. Close the miniBar.

Figure 7.

9. Reversing the door hang (Fig. 8.)

Reversing is suggested to perform in the following

way, in order to avoid breaking of the hinge bolt:

Disconnect the mains

Lay the appliance down carefully on its back

Figure 8.

Take down the two foot-extension (1) pieces by

removing the two screws (2)

Remove the four screws (4) and take out the two

fixing feet (3)

Remove the four screws (7) the upper hing (5)

and the cover cap (6)

Remove the door (8), together with the upper

hinge (5), from the housing

Insert the upper hinge (attached the miniBar)

and the covering plate in the slot on the opposite

side and secure with four screws (7).

Insert the door on the upper hinge and place it.

Mount the fixing feet (3) with hinge bolts (9)

placed into the opposite side of the feet

Mount the two foot-extension pieces (1)

Check that the door closes easily and is sealed

properly.

Green and Yellow: Earth

Blue: Neutral

Brown: Live

The wire coloured green and yellow must be

connected to the terminal marked with the letter "E"

or by the earth symbol or coloured green and

yellow.

The wire coloured blue must be connected to the

terminal "N" or coloured black.

The wire coloured brown must be connected to the

terminal marked "L" or coloured red.

Upon completion there must be no cut, or stray

strands of wire present and the cord clamp must be

secure over the outer sheath.

10. Customer service

Before you call a service engineer, carry out the

following simple tests:

If after checking all the above points, the refrigerator is

still not working satisfactorily, contact your nearest

service engineer. State the problem, model, product-

and serial-number.

(Details of the model, product- and serial-number are

to be found on the data label in the top left of the

inside compartment.)

In the event of a fault developing, contact your nearest

Service Centre-see local telephone directory.

11. Putting into operation

Technical data:

11.1. Connecting to electrical mains

The appliance may only be operated from

nominal voltage mains as shown on the data

plate. The appliance mains plug may be connected to

a mains socket earthed in accordance with regulations.

Any electrical work required to install this appliance

should be carried out by a qualified electrician or

competent person.

The manufacturer declines any liability should

these safety measures not be observed.

Electrical Requirements

Before switching on, make sure the electricity supply

voltage is the same as that indicated on the appliance

rating plate.

Only for UK:

The appliance is supplied with a 3 Amp plug fitted. In

the event of having to change the fuse in the plug

supplied, a 3 Amp ASTA approved (BS 1362) fuse

must be used. Should the plug need to be replaced

for any reason, the wires in the mains lead are

coloured in accordance with the following code:

Model RH 423LDAG RH 439LDAG

Type MB20-60 MB20-60

Gross volume 23 litres 24,5 litres

Mains operation 220 - 240V (AC) 220 - 240V (AC)

Input 75W 65W

Energy consumption 1,02 kWh/24h 1,15 kWh/24h

Climate class N N

Refrigerant 159g H2O+86g NH3147g H2O+98g NH3

Problem

The appliance does not cool sufficiently

The appliance does not cool at all.

Possible cause

Too much food to be cooled was put in.

Door is not shut properly.

Internal air circulation is restricted.

CUC system stopped the operation.

Plug is not connected to the mains socket properly

There is no voltage in the mains socket.

Solution

Put in less food to be be cooled.

Check if the door is shut.

Provide inside cool air circulation.

See operating instruction 5.3.3.

Check if the connection is proper.

Check if there is voltage.

12. Environmental protection

information

The appliance does not contain any CFCs/HCFCs.

Ammonia (natural hydrogen and nitrogen compound)

is used as a refrigerating agent in the refrigeration

unit.

The ozone-friendly cyclopentane is activated as a

motive agent for the PU foam insulation.

Sodium chromate is used for corrosion protection

(less than 2 weight % of the coolant).

13. Recycling

After unpacking the appliance, the packing materials

should be delivered to a local collection site. At the

end of its useful lifetime, the appliance should be

delivered to a specialized collection and

reprocessing firm, which reclaims the usable

materials. The rest is properly destroyed.

Appliances bearing this symbol must be

deposited at the designated local

reception point for the disposal of

electrical and electronic equipment.

It is not permitted that this product be

disposed of by way of the normal

household refuse collection system.

Dometic refrigerators bear this symbol on the

specifications plate (data plate) to be found in the

interior of the unit.

This appliance complies

with the following EEC directives:

LVD-Directive 73/23/EEC with amendment

90/683/EEC

EMC-Directive 89/336/EEC

RoHS - Directive 2002/95/EC

Andere Handbücher für RH 423LDAG

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dometic Kühlschrank Handbücher

Dometic

Dometic myfridge mf5m Bedienungsanleitung

Dometic

Dometic CFF12 Bedienungsanleitung

Dometic

Dometic CLASSIC RM 2620 Bedienungsanleitung

Dometic

Dometic MoBar300S Bedienungsanleitung

Dometic

Dometic DS 300 Bedienungsanleitung

Dometic

Dometic RH 161 LD Bedienungsanleitung

Dometic

Dometic CFF SERIES Bedienungsanleitung

Dometic

Dometic NEA1402 Bedienungsanleitung

Dometic

Dometic REFRIGERATION 10-Series Bedienungsanleitung

Dometic

Dometic REFRIGERATION 10-Series Bedienungsanleitung

Dometic

Dometic RM3663 Bedienungsanleitung

Dometic

Dometic RM211 Bedienungsanleitung

Dometic

Dometic HiPro 3000 Technisches Handbuch

Dometic

Dometic TL200 Bedienungsanleitung

Dometic

Dometic NDR1062 Bedienungsanleitung

Dometic

Dometic RM2452 Handbuch

Dometic

Dometic RMS 8465 Bedienungsanleitung

Dometic

Dometic PowerFridge RC3000 Bedienungsanleitung

Dometic

Dometic REFRIGERATION 10-Series Bedienungsanleitung

Dometic

Dometic 9 SERIES Bedienungsanleitung

Dometic

Dometic RM2604 Bedienungsanleitung

Dometic

Dometic DE15F Bedienungsanleitung

Dometic

Dometic Americana Bedienungsanleitung

Dometic

Dometic A 602K Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung