Dormakaba 8600 EMF Bedienungsanleitung

8600 EMF

Surface Applied Closer (no Detector)

Installation instructions

08281020 – 03-2020

| EN |

28600 EMF 03-2020

08281020

dormakaba 8600 EMF Installation Instructions Table of Contents

Table of contents

1 Technical specifications 3

1.1 Preparation notes 3

2 Installation instructions 4

2.1 Install closer to door 4

2.2 Remove wire access plug 4

2.3 Secure track to frame 5

2.4 Set up wire connections 5

2.5 Secure main arm 6

2.6 Secure arm to slide shoe 6

3 Adjustments 7

3.1 Adjust closing speeds: sweep, latch, backcheck,

delayed action 7

3.2 Adjust spring force 7

3.3 Adjust hold open 8

3.4 Auxiliary stops 8

4 Bypass switch (optional) 8

4.1 Secure bypass switch 8

5 Final steps 9

5.1 Determine power supply 9

5.2 Check connections 9

5.3 Unit testing 10

5.4 Operation 10

5.5 Covers 10

dormakaba 8600 EMF Installation Instructions

08281020 03-20208600 EMF 3

Technical specifications

1 Technical specifications

. Preparation notes

1. Each (HO) hold open unit contains a door closer

and track assembly with hold open

electromagnet. The unit can be connected

directly to a fire control panel.

2. Read entire instruction sheet prior to installation

and refer to NFPA 72E. Standards may be

obtained from THE NATIONAL PROTECTION

ASSOCIATION, Batterymarch Park, Quincy, MA

02269.

3. Reference unit carton for unit mounting style and

voltage.

4. Prepare door and frame for fasteners using the

appropriate template. Mark, drill, and tap holes

as indicated. If surface wiring is used, omit 7/8”

hole for wire access.

dormakaba 8600 EMF Installation Instructions

08281020 03-20208600 EMF

Track

Wire access plug

2 Installation instructions

2.2.1 Remove one wire access plug according to the

installation type.

NOTE: Three access wire holes on optional surface

wired units only.

T & DE (RH)

T & DE (LH)

Surface wiring

NOTE: No top plug on

PT mounts

. Install closer to door

Fig.

8600T and 8600DE

Right hand door

8600PT

Right hand door

Left hand door

Hinge Hinge

. Remove wire access plug

Fig.

dormakaba 8600 EMF Installation Instructions

08281020 03-20208600 EMF 5

Track

Wire connections

2.4.1 Slide wiring connection cover to allow access to

wire connections.

2.4.2 Determine power supply and unit voltage type:

24 VAC, 24VDC.

CAUTION! DO NOT CONNECT 120VAC TO A 24 VOLT

UNIT TYPE!

2.4.3 Connect power supply wires to terminal block as

shown (Terminal Block can be removed for easier

wiring).

NOTE: Be sure to use ground screw for power supply

ground wire when supplying 120 VAC.

2.4.4 Slide wiring connection cover over wire

connections.

2.4.5 Insert cover into track, align end cap in end of

track.

2.4.6 Install remaining screw as shown using 1/4-20x2”

metal or No.14 x 2-3/4” wood screw.

2.3.1 8600T and 8600DE:

• Install the wire access plugs toward latch edge

of door.

• Use (2) 1/4-20x2” metal or (2) No.14 x 2-3/4”

wood screws.

• Route wires from frame through appropriate

wire access hole in track, being careful not to

pinch wires during installation.

8600T and 8600DE

Wire

connection

cover

8600PT

Hinge

2.3.2 8600PT:

• Install PT track to soffit with wire access plugs

toward hinge.

• Install with (1) 1/4-20x1-1/4” combo screw and

(1) 1/4-20x2” metal or (1) No.14 x 2-3/4” wood

screw as shown.

• Route wires from frame through appropriate

wire access hole in track, being careful not to

pinch wires during installation. (DO NOT

INSTALL END CAP ON HINGE SIDE OF THIS

STEP.)

End cap

. Secure track to frame

Fig.

End cap

. Set up wire connections

Fig.

CAUTION! IMPROPER

VOLTAGE TO UNIT

WILL RESULT IN

DAMAGE TO UNIT

AND VOID

WARRANTY.

NOTE: ALL WIRING

MUST COMPLY WITH

NATIONAL, STATE

AND LOCAL

ELECTRICAL CODES.

Terminal

block

Solenoid wires

Incoming power

connection

UL listed alarm

control unit or

smoke detector

NOTE: THIS CONNECTION IS NOT POLARITY

DEPENDENT. TERMINAL BLOCK 18 awg MAX.

UL listed alarm

control unit or

smoke detector

dormakaba 8600 EMF Installation Instructions

08281020 03-20208600 EMF

Main arm

. Secure arm to slide shoe

Fig.

2.6.1 Secure arm to slide shoe. 2.6.2 Use 3/16” hex head wrench.

. Secure main arm

Fig.

2.5.1 Place arm on top

pinion at 45°

angle.

2.5.2 Secure arm with

pinion screw and

washer.

6mm hex key

Left hand doorRight hand door

8600T

8600DE

8600PT

Hinge

LHinge

2.5.1 Place arm on top

pinion at 45°

angle.

2.5.2 Secure arm with

pinion screw and

washer.

2.5.1 With door in closed position, rotate

spindle 45° with wrench.

2.5.2 Place arm on top pinion.

2.5.3 Open door and secure with pinion screw and washer.

Left hand doorRight hand door

Left hand door Right hand door

6mm hex key

6mm hex key 6mm hex key

45° 45°

Rotate

pinion

Rotate

pinion

dormakaba 8600 EMF Installation Instructions

08281020 03-20208600 EMF 7

Adjustments: closing speeds

Adjustments: spring force

3 Adjustments

. Adjust closing speeds: sweep, latch, backcheck, delayed action

Fig.

. Adjust spring force

Fig.

8916: Supplied with a size 3 spring setting

8956: Supplied with a size 6 spring setting.

Regular Mount, Pull side closers

Closer size Max door

weight (lbs)

Door width Full turns

Interior Exterior

8616

3 100 2'6" -11

4 125 3' 2’6” 0

5 150 3'6" 3’ +5

6 200 ‘4’ 3’6” +13

8656 5 150 3’6” 3’ -7

6 200 4' 3’6” 0

Latch

Sweep

Delayed action

Backcheck positioning

Backcheck

NOTE:

DO NOT ADJUST SPRING LOWER THAN SIZE 3.

dormakaba 8600 EMF Installation Instructions

08281020 03-20208600 EMF

Adjustments: hold open

Auxiliary stop

Bypass switch

Fig.

Hold open position is preset at approximately 90°. Loosen set screws using 3/32” hex wrench. Slide hold open

device to desired position. Retighten set screws securely.

Hold open device

Hold open set screws -

3/32” hex

Hold open force adjustment - 5/32 hex.

Clockwise = stronger

Less Hold Open Angle

Greater Hold Open Angle

NOTE: Power must be

supplied to reset position.

An auxiliary door stop (by others) must be installed to limit the maximum degree

of door swing. Failure to do so may result in damage to the unit.

4 Bypass switch (optional)

Fig.

4.1.1 Slide wiring connection cover to allow access. 4.1.2 Attach bracket and assembly bypass switch.

Wire connection

cover

. Secure bypass switch

. Adjust hold open

. Auxiliary stops

Fig.

dormakaba 8600 EMF Installation Instructions

08281020 03-20208600 EMF 9

Power supply

Check connections

. Determine power supply

Fig.

5.1.1 Determine power supply and unit voltage type:

24VAC/24VDC.

CAUTION! DO NOT CONNECT 120-VAC TO A 24 VOLT

UNIT TYPE!!!

5.1.2 Connect power supply wires, one (1) to terminal

block one (1) to bypass switch.

5.1.3 Connect other bypass switch wire to terminal

block. (Terminal block can be removed for easier

wiring).

5.1.4 Slide wiring connection cover over wire

connections.

Wire

connection

cover

Bypass

switch

Terminal

block

Incoming

power

connection

UL listed alarm

control unit or

smoke detector

5 Final steps

1. After installation is completed, check all connections. Apply power to units.

2. Open door so slide block engages with hold open assembly.

3. Advise fire officials prior to testing.

4. Activate system into alarm so the electromagnet releases and the doors close.

5. If the closer is used in conjunction with a detectored unit, trip the test switch of the main closer

detector as explained in the test procedure for that unit. After a short time delay, the hold open

electromagnet of both units will release and the doors will close. Resetting the test switch will allow

the units to return to standby.

. Check connections

dormakaba 8600 EMF Installation Instructions

08281020 03-20208600 EMF

Testing

Operation

Covers

IMPORTANT: THE UNIT MUST BE TESTED AFTER THE INSTALLATION, BY THE END USER, TO ASSURE

THAT THE DOOR CLOSER UNITS FUNCTION PROPERLY WHEN THE ALARM SYSTEM IS ACTIVATED.

THE ENTIRE SYSTEM MUST ALSO BE TESTED PERIODICALLY AFTER THE INITIAL INSTALLATION TEST,

IN CONJUNCTION WITH THE TESTING OF THE FIRE ALARM SYSTEM. THE END USER IS ALSO

RESPONSIBLE FOR THE ADJUSTMENTS AND MAINTENANCE TO RETAIN THE SYSTEM IN WORKING

ORDER.

NORMAL: The closer unit’s solenoid will be

energized across a normally closed

alarm contact from 24VDC, 24VAC

or 120VAC power supply based on

unit voltage.

FIRE ALARM: When the alarm sounds, the

alarm contact will open and

interrupt current to the solenoid

which releases the hold open

allowing the door to close and latch.

ELECTRICAL SPECIFICATION:

Voltage input - 24VDC + 10% - 15%

24VAC + 10% - 15%

Maximum input current - 24VDC 166mA

24VAC 166mA

. Operation

. Covers

Fig.

COV

FCSL FMC

. Unit testing

Inhaltsverzeichnis

Andere Dormakaba Türöffnungssystem Handbücher

Dormakaba

Dormakaba G-EMR-140 Handbuch

Dormakaba

Dormakaba RTS Series Bedienungsanleitung

Dormakaba

Dormakaba ED50LE Bedienungsanleitung

Dormakaba

Dormakaba RTS88 Bedienungsanleitung

Dormakaba

Dormakaba ED100 Bedienungsanleitung

Dormakaba

Dormakaba HSW EASY SAFE Bedienungsanleitung

Dormakaba

Dormakaba UNIVERSAL PT 60 Bedienungsanleitung

Dormakaba

Dormakaba EN 2-5 Bedienungsanleitung

Dormakaba

Dormakaba UNIVERSAL PT 29 Bedienungsanleitung

Dormakaba

Dormakaba ED50 Bedienungsanleitung

Dormakaba

Dormakaba ITS9613 Bedienungsanleitung

Dormakaba

Dormakaba ED50 Bedienungsanleitung

Dormakaba

Dormakaba 8900 T Bedienungsanleitung

Dormakaba

Dormakaba ED50LE Bedienungsanleitung

Dormakaba

Dormakaba TS 98 XEA Bedienungsanleitung

Dormakaba

Dormakaba ED900 Bedienungsanleitung

Dormakaba

Dormakaba TS 93 G EN 2-5 Bedienungsanleitung

Dormakaba

Dormakaba TS9356 PKT 120/170 Bedienungsanleitung

Dormakaba

Dormakaba Muto Premium XL120 Bedienungsanleitung

Dormakaba

Dormakaba ED50 Bedienungsanleitung

Dormakaba

Dormakaba 8900 JT Bedienungsanleitung

Dormakaba

Dormakaba 8600T EMR Bedienungsanleitung

Dormakaba

Dormakaba ED100 Bedienungsanleitung

Dormakaba

Dormakaba ED900 Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Label

Label NEPTIS/LE Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Olide

Olide 120B Bedienungsanleitung

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung