Dormakaba Saflok Quantum Pixel Bedienungsanleitung
Saflok Quantum® Pixel
Installation Instructions
PK3693-T - 2019 - 02
EN
2 Saflok Quantum Pixel PK3693_T 02-19
©2018 dormakaba USA, Inc. All trademarks and registered trademarks are the property of their respective owners.
Saflok Quantum Pixel Installation Instructions
CAUTION
WARNING
IMPORTANT
All parts needed to install the Quantum Pixel lock are included with each unit. Please check to make sure
all parts are accounted for before you begin the installation. Do not substitute any of the parts. The use
of substitute parts will result in poor performance of the lock.
All information contained herein, including but not limited to product pricing and other intellectual
property, is confidential and intended for the sole use of the addressee(s) so named. Any misuse of this
confidential information contained herein may result in legal action by dormakaba USA Inc. and
its parent company.
Door and door frame preparation
Tools required for this step
Recommend doors prepped at factory for higher precision
Do not drill both STD and ADB Ø7/16 thumb turn holes. Drill only the hole that corresponds to the mortise
purchased. Do not drill a Ø7/16 thumb turn hole for utility locks.
• Drill
• Plunge Router
- 1” Straight
- 1-⁄” Straight
• Drill bits
- ⁄” Reader
- ⁄” Thumb Turn
- ⁄” Mortise Mounting
• 2-⁄" Hole Saw
• Chisel
• Jigsaw
• 1:1 Door Prep Templates
• Optional Door Prep Jig P/N: FIXT-PIXEL (available for purchase)
- Door prep jig only available for 1-3/8" [34.9mm] OR 1-3/4" [44.5mm] doors with standard centered
lower mortise pocket and no rabbet.
Saflok Quantum Pixel PK3693_T 02-19 3
Figure 1 - Exploded Lock View
Controller face plate
#8-32 X 1/4 Flat Head Screws
#6 X 1/2 Flat Head Screws
#6 X 1/2 Flat
Head Screws Reader Cover
Reader Base
Lock Controller
#12 X 1 Pan
Head Screws
#4 X 3/16 Screw
Antenna PCB
Thumb Turn Base
Thumb Turn
Strike Plate
I/S Lever Rose
I/S Lever Assy
O/S Lever Assy
#12 X 1-1/2
OR
#12-24X 3/8
Flat Head Screws
#8-32 X 1/4 Flat Head Screws
Mortise Face Plate
Mortise
#12 X 1-1/4 Flat Head Screws
#8-32 Shoulder Screws
Figure 2 - Door preperation jig
Door and door frame preparation
4 Saflok Quantum Pixel PK3693_T 02-19
Door and door frame preparation (continued)
Figure 3 - Door preperation templates
*NOT TO SCALE
PAGE 1 - O/S TRIM &
LOWER MORTISE
PAGE 2 - I/S TRIM
PAGE 3 - UPPER
CONTROLLER MORTISE
PAGE 4 - STRIKE PREP
OUTSIDE
PREP
INSIDE
PREP
x
x
*LOWER MORTISE
CENTERED IN DOOR
*UPPER MORTISE OFFSET TO O/S DOOR
FACE IF GREATER THAN 1-3/4" DOOR
THICKNESS.
*CENTERED FOR 1-3/8" TO 1-3/4" DOOR
THICKNESS.
Saflok Quantum Pixel PK3693_T 02-19 5
Lock trim installation
Tools Required for Installation
• Driver handle (P/N: 24190)
• #1 Philips bit
• #2 Philips bit
• #3 Philips bit
• T-15 tamper resistant torx bit (P/N: A39250)
• Spanner wrench for thumb turn (P/N: A32370)
1. Lower Mortise Installation
a. Pre-Drill #12 screw pilot holes
b. Slide mortise into lower pocket
c. Route mortise cable harness along the side wire channel that connectsthe
top and bottom mortise pockets (see figure #6 for wire channel location)
d. Secure with included #12 flat head screws
e. Ensure wire harness is free and not pinched
Figure 5 - Lock Exploded View with Mounted Controller and Mortise
Figure 4 - Pixel Controller and
Mortise Mounting
6 Saflok Quantum Pixel PK3693_T 02-19
Lock trim installation (continued)
2. Controller Assembly Installation
a. Lift controller to top of pocket and center horizontally to mark pilot hole locations based on case
mounting holes
b. Pre-Drill #12 screw pilot holes, ensure holes are centered for proper face plate alignment
c. Slide tray out partially from controller to ensure tabs are not bent when securing #12 screws
d. Lift and center assembly to ensure proper alignment
e. Secure with included #12 pan head screws
f. Slide the tray out partway to and ensure all connections are secure
*Do not connect the battery at this point
g. Connect the harnesses from the mortise and controller together
*Do not seat the slide tray in door at this point
Figure 6 - Wire Channel in Door Edge
Wire Channel
Figure 7 - Controller and Mortise Harness Connection
Saflok Quantum Pixel PK3693_T 02-19 7
Lock trim installation (continued)
3. Reader Assembly Installation
Figure 8 - Exploded Reader Assembly
Reader Cover
Reader Base
Antenna PCB
#6 X 1/2 Flat
Head Screws
#4 X 3/16 Pan
Head Screw
a. Remove the antenna from the antenna base by removing the #4 mounting screw
b. Align the reader base to the 6 pin antenna socket (inside controller assembly)
with the orientation arrow facing up
c. Ensure base is level and mounting holes are horizontal
d. Mark hole centers using center punch to ensure alignment is maintained
e. Drill small pilot hole with a short depth to aid in securing the screws
*Short depth is required so that controller case is not drilled into and damaged
**Don't apply too much pressure when drilling to help maintain door integrity
f. Secure the reader base to the outside of the door using the included #6 flat head screws
*Don't apply too much torque, but ensure base is fully seated against door
g. Plug the antenna into the 6 pin socket visible through the hole in the door
Figure 9 - Reader Base
i. Align pins in upper opening
ii. Insert antenna PCB by sliding the pins carefully into the socket
*Minimal force required if properly aligned
h. Secure the antenna to the base using the #4 pan head screw removed in step a
4. Initial lock power up
a. Connect the battery to the PCB. Green LED should flash 4 times
b. Present a valid keycard to the reader. Red and green LEDs will flash and motor will activate
c. Seat the tray into the controller being careful to not pinch any wires
8 Saflok Quantum Pixel PK3693_T 02-19
Installing the lock trim (continued)
Figure 10 - Exploded Lever Set Assembly
I/S Lever Assy
O/S Lever Assy
I/S Lever Rose
#8-32 Shoulder Screws
5. Lever Set Installation (If supplied by dormakaba)
a. Place the outside lever rose assembly on the outside of the door
b. Place the inside lever rose assembly on the inside of the door
c. Secure to the outside rose assembly using the included shoulder screws
d. Carefully slide the escutcheon over the lever and ensure removal notch is aligned below
lever set for concealment
Saflok Quantum Pixel PK3693_T 02-19 9
Installing the lock trim (continued)
Figure 11 - Exploded Thumb Turn Assembly
Thumb Turn Thumb Turn Base
#6 X 1/2 Flat
Head Screws
6. Thumb Turn Installation (If supplied by dormakaba)
a. Align base centered over the mortise cam (not hole in door)
b. Mark hole centers using center punch to ensure alignment is maintained
c. Drill small pilot hole with a short depth to aid in securing the screws
d. Secure the base to the door with the included screws
e. Align turn piece onto base so that it is at 12 and 6 o'clock (see figure #12)
Figure 12 - Thumb Turn Base Alignment
Mortise Cam
f. Install the turn piece onto the base by screwing the collar on clockwise until tight; torque secure
with spanner wrench
g. Check the turn for smooth operation ensuring no drag or binding occurs
*If binding occurs; verify base alignment with mortise cam
7. Faceplate Installation
a. Install lower mortise faceplate using #8 flat head screws
b. Install upper controller assembly faceplate using #8 flat head screws
*Ensure the controller harness does not become pinched when securing faceplates
10 Saflok Quantum Pixel PK3693_T 02-19
Lock functionality testing
1. Initial Lock Test (Construction Mode)
a. Present a valid opening key to the reader
b. Ensure lock unlatches, lever turns freely, and lock re-latches
2. Lock Programming
a. Use HH6 to program lock to desired room number (see figure #13 for USB programming port)
Figure 13 - USB Programming Cable Connection
3. Reader Cover Installation
a. Locate release hole at 5:00 (see figure #14)
b. Place the lens onto the base and rotate clockwise to secure at 6:00
c. Ensure cover is secured (locking tab will click when fully seated)
*For ease of assembly and disassembly; wrap thumb around circumference of cover to get a good grip
Figure 14 - Reader Cover Installation
Inhaltsverzeichnis
Andere Dormakaba Sperren Handbücher
Dormakaba
Dormakaba RCI DE8310 Bedienungsanleitung
Dormakaba
Dormakaba 8H Series Bedienungsanleitung
Dormakaba
Dormakaba UNIQUIN Bedienungsanleitung
Dormakaba
Dormakaba RCI 3513-DM Bedienungsanleitung
Dormakaba
Dormakaba SafeRoute-System Mini Bedienungsanleitung
Dormakaba
Dormakaba BEST Wi-Q 45HQ Bedienungsanleitung
Dormakaba
Dormakaba La Gard Reset Box Bedienungsanleitung
Dormakaba
Dormakaba LA GARD 700 Series Bedienungsanleitung
Dormakaba
Dormakaba 2725-K6 Bedienungsanleitung
Dormakaba
Dormakaba STV 2 Series Bedienungsanleitung
Dormakaba
Dormakaba AUDITCON 2 SERIES Bedienungsanleitung
Dormakaba
Dormakaba 5715 Bedienungs- und Wartungsanleitung
Dormakaba
Dormakaba GL10 Bedienungsanleitung
Dormakaba
Dormakaba M Series Bedienungsanleitung
Dormakaba
Dormakaba Axessor CIT Bedienungsanleitung
Dormakaba
Dormakaba Classic Bedienungsanleitung
Dormakaba
Dormakaba ORACODE 660i Bedienungsanleitung
Dormakaba
Dormakaba SVI 5000 Schulungshandbuch
Dormakaba
Dormakaba RCI DE8310 V1.6 Bedienungsanleitung
Dormakaba
Dormakaba STV 1 Series Bedienungsanleitung
