Doro 313C Bedienungsanleitung

doro 313C

Manual

2 www.doro.com

English

www.doro.com 3

1 Call Number

2 OK/Cancel button

3 Hanging Hook for Handset

4 Select Caller ID mode

5 Handset Volume Control

6 Store Button

7 Memory button

8 Recall button

9 Redial button

10 Hands Free Button

11 Controls for hands free

12 Handset earpiece tone control

13 One-touch memory buttons M1/M2

14 Controls for ringer

15 Scrolling Buttons

16 New CID message and Visual

Ring Indicator

17 Select Phone Book mode

18 Warning tone control

English (see pages 3-15)

2 www.doro.com

English

www.doro.com 3

Installation

Important!

Please note when programming all references to press = to press once and then immediately

release the button.

The earpiece of the handset may attract small ferromagnetic objects such as staples and pins,

care should be taken when placing the handset near these items.

Connection/Basic setting

1. Connect the curly cord to the handset and to the socket marked Q on the

side of the telephone.

2. Connect the mains adapter to the socket marked DC 9V on the back of the

telephone and then to an electrical wall socket.

3. The display should ash the word ENGLISH. If not press and hold v for

approximately 4 seconds.

4. Select the desired language using v/V. Press 0.

5. Select the desired contrast setting (3=normal) using v/V. Press 0.

6. Set the hour (00-24) using v/V. Press 0.

7. Set the minute using v/V. Press 0.

8. Set the day using v/V. Press 0.

9. Set the month using v/V. Press 0.

10. Ensure the correct dialling method is displayed (ie: TONE). Press 0

11. Select the required ringer melody using v/V. Press 0

12. Ensure the correct Recall time is displayed (ie: 100). Press 0

13. Connect the telephone line cord to the socket marked T on the back of the

telephone, and then to a network wall socket.

14. Lift the handset and listen for the dial tone.

To change any of the above settings, press and hold v for approximately 4

seconds and repeat steps 4. - 12. above.

English

4 www.doro.com

English

www.doro.com 5

Installation

Batteries

Four good quality AA alkaline batteries can be installed to protect the memory

during prolonged power failure. When the batteries are running low will be

displayed.

1. Disconnect the telephone line cord.

2. On the underside of the telephone carefully remove the battery cover.

3. Insert the backup batteries ensuring correct battery polarity is observed.

4. Replace the battery cover.

5. Reconnect the telephone line cord.

Wall mounting

The telephone can be wall mounted by using the included wall mount bracket. It

can also be tted to a standard wall plate without using screws in Australia.

1. Secure two screws, vertically positioned 83 mm apart.

2. The screws should locate into the two keyholes on the back of the telephone.

3. Remove the hanging peg (located by the hook switch) by pushing it upwards.

4. Rotate the hanging peg 180 degrees, and then replace it.

The display

When the telephone is not in use the date and time, number of new and total

number of calls stored in the Caller ID memory will be shown in the display.

The display will illuminate during ringing, when accessing memory functions

and dialling out.

English

4 www.doro.com

English

www.doro.com 5

Operation

Making a call

Normal Dialling

1. Lift the handset.

2. Dial the desired telephone number.

Pre-Dialling

This allows you to enter and change a telephone number before it is dialled.

1. Enter the required telephone number. Mistakes can be erased by pressing 0.

2. You can now either lift the handset, press OR s, the displayed

telephone number will now be dialled.

Please note!

During a conversation, you can switch from the handset to hands free mode at any time by

pressing s. Press s again to terminate the call.

Redial function

If the number dialled is engaged or you wish to redial the last number called

simply lift the handset (or press s) and press r.

Volume control

The handset earpiece volume may be adjusted during a call using /

The audible response within the earpiece may be adjusted using ♫

located on the side of the unit.

To adjust the speaker volume (hands free), use located on the side of the

telephone.

Warning!

Do NOT select the maximum handset volume unless you already

having hearing difculties.

English

6 www.doro.com

English

www.doro.com 7

Operation

Timer

Immediately after dialling a telephone number a call timer will be shown on the

display. The timer is a simple way to help you keep track of how long the call

lasts.

Hands free function

1. Press s. The speaker will be activated and the Hands free indicator light

will illuminate.

2. Dial the required telephone number. The speaker volume can be adjusted

using located on the side of the telephone.

3. Speak towards the microphone located on the front edge of the telephone.

4. Press s to terminate the call.

Please note!

During a conversation, you can switch from the hands free to handset mode at any time by

picking up the handset. Replace the handset to terminate the call.

Please remember that in hands free speaker mode it is only possible for one person at a time

to talk. The switch over between speaker and microphone is automatic and dependent on the

sound level of the incoming call and the microphone respectively. It is therefore essential that

there are no loud noises, e.g. music, in the immediate vicinity of the telephone, as this will

disrupt the speaker function.

Warning tone

A warning tone can be selected using the switch located on the back of the

unit, if the handset is then not replaced correctly an alarm will sound after 20

minutes.

English

6 www.doro.com

English

www.doro.com 7

Phone Book

Using the Phone Book

The Phone Book will store 32 telephone numbers (22 digits max)and their

associated names (16 characters max) with entries arranged alphabetically.

A stored phone number can be dialled using fewer keystrokes than if dialled

manually. If you subscribe to a Caller ID service, the name/number of the caller

will be shown when you receive an incoming call (only for those numbers stored

in the Phone Book or M1/M2 memories).

Letters

Each number key has been allocated certain characters.

Button Letters/symbols

1.......................................... [Space character] + & - / X 1

2.......................................... A B C Å Ä Æ æ å ä ß 2

3.......................................... D E F ë 3

4.......................................... G H I ï 4

5.......................................... J K L 5

6.......................................... M N O Ñ ñ ö @ ö 6

7.......................................... P Q R S 7

8.......................................... T U V Ü ü 8

9.......................................... W X Y Z 9

* .......................................... ` @ ( ) * < >

0.......................................... , . : ? = 0

#.......................................... $ _ % ! #

Storing names/numbers

1. Press b.

2. Press P.

3. Press P again.

4. Enter the telephone number to be stored (up to 22 digits). Press P.

5. Enter the name (up to 16 characters). Press the corresponding number

button one or more times for the rst letter (see the table above).

6. Press P.

Press r if you need to insert a pause in the telephone number.

If you wish to change a number, store the new number in the same location as the old one.

English

8 www.doro.com

English

www.doro.com 9

Phone Book

Dialling from the Phone Book

1. Press b.

2. Scroll to the required memory location using v/V

. To quick-search in the

Phone Book press the corresponding number button one or more times for

the rst letter (refer to the table on the previous page).

3. Press to dial the displayed number. If you do nothing the phone will

return to standby mode.

Please note!

During a conversation, you can switch from the handset to hands free mode at any time by

pressing s. Press s again to terminate the call.

Changing phone numbers/names

1. Press b.

2. Scroll to the required memory location using v/V

3. Press and hold P until EDIT? is displayed. Press P.

4. Changes to the displayed telephone number can be made using 0 and v/V

Press P.

5. Changes to the displayed name can be made using 0 and v/V

6. Press P to conrm the changes.

Deleting a phone book entry

1. Press b.

2. Scroll to the required memory location using v/V

3. Press 0. DELETE? will be displayed.

4. Press and hold 0 until the displayed telephone number disappears.

Deleting all entries in the Phone Book

1. Press b.

2. Scroll to the required memory location using v/V

3. Press and hold 0 until the display shows DELETE ALL?

4. Press and hold 0 until the displayed telephone number disappears.

English

8 www.doro.com

English

www.doro.com 9

Phone Book

Memory

The telephone also has 2 one-touch and 10 two-touch memories for frequently

dialled telephone numbers.

When a number is stored into memory you only press one or two buttons

dependent on location to make a call.

The one-touch memories are M1-M2, the two-touch memories are accessed

using the telephone keypad digits 0-9.

Storing One-touch Memories

1. Press P.

2. Enter the telephone number to be stored (up to 22 digits). Press P.

3. Enter the name (up to 16 characters). Press the corresponding number

button one or more times for the rst letter (see the table for the Phone

Book). Press P.

4. Press either M1-M2 to store the number.

Dialling using One-touch Memories

1. Lift the handset (or press s) and wait for a dialling tone.

2. Press either M1-M2, the stored telephone number will now be dialled.

Storing Two-touch Memories

1. Press P.

2. Enter the telephone number to be stored (up to 22 digits). Press P.

3. Enter the name(up to 16 characters) . Press the corresponding number

button one or more times for the rst letter (see the table for the Phone

Book). Press P.

4. Press either 0-9 to store the number.

Dialling using Two-touch Memories

1. Lift the handset (or press s) and wait for a dialling tone.

2. Press m

3. Select a memory location by pressing the relevant keypad digit 0-9.

Press r if you need to insert a pause in the telephone number.

If you wish to change a stored telephone number, store the new number in the same location as

the old one.

English

10 www.doro.com

English

www.doro.com 11

Caller Identication

Explanation of Caller ID

Caller ID allows you to see who is calling before you answer a call and to see

who has called in your absence. If the number is stored in the Phone Book, the

callers name will be shown instead. Received calls are stored chronologically

with the sequential number shown in the top right hand side of the display.

When the Caller ID log is full, the oldest number will be deleted automatically

as the new call is logged. New calls are indicated by text in the display and

ashing of the red ring indicator light.

Please note!

In order for numbers to be shown, the Caller ID service must be provided by your network

operator and a current subscription in place. Contact you operator for more information.

Retrieving and dialling CID numbers

1. Press to select caller-id mode.

2. Press either v or V to review the numbers stored in the Caller ID memory.

3. To dial a displayed telephone number either press OR s, the displayed

telephone number will now be dialled. If you do nothing the phone will

return to standby mode.

Please note!

During a conversation, you can switch from the handset to hands free mode at any time by

pressing s. Press s again to terminate the call.

Messages

Besides showing telephone numbers, the display can show a number of text

messages or symbols:

OUT OF AREA It is an International call or a call from a PBX (no

information received).

PRIVATE Information on the number is blocked. The call could

also be from a PBX.

q New number not previously recorded or logged.

Z Several calls have been received from the same caller.

Andere Handbücher für 313C

Inhaltsverzeichnis

Andere Doro Telefon Handbücher

Doro

Doro PHONEEASY RECORD 327CR Bedienungsanleitung

Doro

Doro 915c Syntiro Bedienungsanleitung

Doro

Doro COMFORT 3000 Bedienungsanleitung

Doro

Doro AFTI 40 Bedienungsanleitung

Doro

Doro HEARPLUS 313CI Bedienungsanleitung

Doro

Doro Magna 4000 Bedienungsanleitung

Doro

Doro COMFORT 3000 Bedienungsanleitung

Doro

Doro CONGRESS 200 Bedienungsanleitung

Doro

Doro AlertEasy 314C Bedienungsanleitung

Doro

Doro 916CR Bedienungsanleitung

Doro

Doro CONGRESS 150 Bedienungsanleitung

Doro

Doro AUB 3 Bedienungsanleitung

Doro

Doro 914c Bedienungsanleitung

Doro

Doro PhoneEasy 311C Bedienungsanleitung

Doro

Doro AUB 200 Bedienungsanleitung

Doro

Doro MemoryPlus 319ph Bedienungsanleitung

Doro

Doro COMFORT 4005 Bedienungsanleitung

Doro

Doro 313C Bedienungsanleitung

Doro

Doro 4100H Bedienungsanleitung

Doro

Doro HearPlus 317ci Bedienungsanleitung

Doro

Doro 509C Bedienungsanleitung

Doro

Doro Magna 2005 Bedienungsanleitung

Doro

Doro PHONEEASY 410GSM Bedienungsanleitung

Doro

Doro AL503 Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

D-Link

D-Link DWR-720/PW Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Panasonic

Panasonic KX Series Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung