Dostmann Electronic P705 Bedienungsanleitung

Operation Manual

SERIE

Precision Measuring Instruments

P700, P705, P710, P715, P750,

P755, P770, P755-LOG, P770-LOG

DOSTMANN electronic

P700

DE P700 Anleitung engl. 12/11 06.12.2011 10:04 Uhr Seite 1

Retractable stand

Mounting device for

probe handle

Measuring port 1

Measuring port 2

(P705, P715, P755,

P770, P755-LOG,

P770-LOG)

USB PC interface

port

Big

LC-Display

Keyboard

Unit diagram

DE P700 Anleitung engl. 12/11 06.12.2011 10:04 Uhr Seite 2

Operation Manual

Summary

1. Handling

1.1. General advices

1.2. Setting to work

1.3. Switch on/off

1.4. Menu

1.4.1. Measuring unit switching (UNIT)

1.4.2. Probe selection (Prob)

1.4.3. Difference temperature (Lin2)

1.4.4. Calibration (CAL)

1.4.4.1. Calibration

combination probe

(temperature/humidity)

1.4.5. Channel activation (Chnl)

1.4.6. Enter Area for volume flow (ArEA)

1.4.7. Memory setup (Lo6)

1.5. Recalling memory data

(HOLD/MAX/MIN/AVG)

1.6. Measuring rate (FAST-modus)

1.7. AUTO-OFF-function

1.8. Special-functions

1.8.1 Ohm/microvolt/volt/hertz display

1.8.2 Zero adjustment

1.8.3 Deactivation of the 2nd channel (toggle)

2. Power supply / Changing the battery

3. Error codes / troubleshooting

4. Technical data

5. Interface protocol

6. Connector layout

7. Data of probe-calibration

8. Guarantee

DE P700 Anleitung engl. 12/11 06.12.2011 10:04 Uhr Seite 3

1.1 General advice

• For cleaning the instrument please do not use

abrasive cleaner but a dry or wet piece of cloth.

• Please store the measuring instrument in a dry and

clean place.

• Avoid any force like shocks or pressure to the

instrument.

• Do not use force to connect the probe or interface

plugs in. The interface plug is different from the

probe plug.

• If no sensor is connected to the instrument while

switching on „open“ shows on the display (Please

refer to chapter error codes/troubleshooting).

• A retractable stand on the back of the instrument

allows it to be used as a bench top instrument.

1.2 Operation

Before switching on the instrument, connect the

probe/s to the instrument and insert the battery

(Please refer to chapter 6. Power supply / battery

changing). A number on the instrument's housing

marks each port.

1.3 Switching on and off

By operating the ON/OFF-key the instrument swit-

ched on or off. After switching on the instrument

indicates a full segment test for 1,5 sec., afterwards

the instrument shows the calibration-code and the

adjusted measurement category for channel 1. (Only

2-channel instruments: After additionally 1,5 sec.

the instrument shows the calibration-code and the

adjusted measurement category for channel 2.)

Then it starts operating in measurement mode in-

dicating the actual measurement value (for example:

temperature). All instruments display the measure-

ment value of channel 1 on the top display line (big

display line). Directly below you will see the trending

bargraph. The second channel of our 2-channel

instruments you will see on the bottom line (small

display line).

Fig 1:

Example of channel information after switching on.:

channel 1

Line 1: [oFF P = calibration code of channel 1

according to standard linearization (DIN), probe selec-

tion of channel 1 = Pt100.

channel 2

Line 2: [oFF P = calibration code of channel 2

according to standard linearization (DIN), probe selec-

tion of channel 2 = Pt100.

1. Handling

DE P700 Anleitung engl. 12/11 06.12.2011 10:04 Uhr Seite 4

Note: On all instruments you can select the mea-

surement category (chapter 1.4.2. Prob) according

to the model version. Instruments that are delivered

only with one probe the correct measurement cate-

gory is preset. In other case please check chapter

1.4.2. (Prob) for the correct set-up.

1.4 Menu

The adjustments of the instruments like the mea-

surement value, calibration of Up and down keys

probes, deactivation of channels and so on are

resulting from the structure of the menu. You will

reach into the main menu by pushing

[ENTER/MENUE]. With the up and down keys [



]

you can choose your required menu item. Push

[ESC] to be back in the measuring mode.

Menu structure

1.4.1 Measuring unit switching °C and °F

respective %rH, td or g/m3/ [Unit]

Unit = Measuring unit

Measuring unit temperature

(°C=Celsius, °F=Fahrenheit)

Measuring unit humidity

(%rH=relative humidity, td=dew point, g/m3=abso-

lute humidity)

Important!

Unit

°C

°F

m/s

%rh

g/m3

°C td

°F td

hPa

Prob Lin2 CAL Chnl ArEA Lo6

T1-T2 oFF

oP1

oP2

OFF cOFF

ON mON

m3/s

❶ up and down keys

❷ key [ESC]

❸ key

[ENTER/MENUE]

❶

❷

❸

DE P700 Anleitung engl. 12/11 06.12.2011 10:04 Uhr Seite 5

To change the measuring unit push [ENTER/MENUE].

Use the up and down keys [



] to select Unit.

Push again [ENTER/MENUE]. On the left corner of

the display appears a small 1, which indicates the

selected channel. For changing the channel use the

up and down keys [



] Push [ENTER/MENUE] to

confirm. On the right corner of the display appears

°C or °F, or %rH, td or gm3 (depending on the selec-

ted probe). Use the up and down keys [



] again to

adjust the requested measuring unit and push

[ENTER/MENUE] to confirm. Push [ESC] to be back

in the measuring mode.

1.4.2 Probe selection / [Prob]

Push [ENTER/MENUE] to change a probe. Use the

up and down keys [



] to select Prob. Push

[ENTER/MENUE] to confirm.

On the left corner of the display appears a small 1,

which indicates the selected channel. For changing

the channel use the up and down keys [



]. Push

again [ENTER/MENUE] to confirm. On the right cor-

ner of the display appears the active probe. Use the

up and down keys [



] to change the probe. Push

[ENTER/MENUE] to confirm the requested probe.

Push [ESC] to be back in the measuring mode.

Measurement Probe selection LC-Display Suitable for

(Prob) these types

of measuring

instruments:

Temperature Pt100 (RTD) P700/P705/

P750/P755/P770

P755-LOG/P770-LOG

Temperature Fe-CuNi Typ J for all P700-

instruments

Temperature NiCr-Ni Typ K for all P700-

instruments

Temperature Fe-CuNi Typ L for all P700-

instruments

Temperature NiCrSi-NiSi Typ N for all P700-

instruments

Temperature Pt13Rh-Pt Typ R P700/P705/

P750/P755/P770

P755-LOG/P770-LOG

Temperature Pt10Rh-Pt Typ S P700/P705/

P750/P755/P770

P755-LOG/P770-LOG

Unit



 MENUE

Prob Lin2 CAL PrEn Chnl ArEA Lo6

Unit



 MENUE

Prob Lin2 CAL PrEn Chnl ArEA Lo6

DE P700 Anleitung engl. 12/11 06.12.2011 10:04 Uhr Seite 6

Measurement Probe selection LC-Display Suitable for

(Prob) these types

of measuring

instruments:

Temperature Cu-CuNi Typ T for all P700-

instruments

Humidity %rF P750/P755/P770

P755-LOG/P770-LOG

Flow m/s P750/P755/P770

P755-LOG/P770-LOG

Pressure Pa P750/P755/P770

P755-LOG/P770-LOG

Thermal flow m/s P750/P755/P770

probe P755-LOG/P770-LOG

Note: Please check the probe selection to be sure

that the correct probe is entered. If a measurement

value is changed with the ENTER-key at the menu

Prob, the standard calibration will be automatically

used.

Indications for the combination probes

(temperature and humidity):

Please adjust relatively humidity as measurement

value for the channel on which the combination

probe is plugged. If you want that the measured

temperature of the plugged combination probe is

shown as well, you have to deactivate the channel

on which no probe is plugged on (see chapter

1.4.6./Chnl).

1.4.3 Difference temperature

(only 2-channel instruments) / [Lin2]

To display the difference temperature push

[ENTER/MENUE]. Use the up and down keys [



]

to select Lin2. Push again [ENTER/MENUE]. On the

right corner of the display appears a T1-T2. Use the

up and down keys [



] to adjust the requested sel-

ection. Push [ENTER/MENUE] to confirm. Push

[ESC] to be back in the measuring mode.

Note: Both channel have to be activated for showing

the difference temperature.

1.4.4 Calibration function / [CAL]

Despite high quality manufacturing techniques, each

probe is slightly different from specified standards.

To eliminate inaccuracies caused by exchanging or

ageing of probes, the instrument offer easy calibra-

tion functions which guarantee that the system

accuracy is always as good as if the instrument was

specifically calibrated to the individual probes in our

laboratory.

Important!

Unit



 MENUE

Prob Lin2 CAL PrEn Chnl ArEA Lo6

DE P700 Anleitung engl. 12/11 06.12.2011 10:04 Uhr Seite 7

The instruments offer three calibration options:

1) [OFF]:Standard characteristic curve (e.g. Pt100-

resistance according DIN IEC 60751)

2) [OP1]:Calibration by code (2 x four digit code) is

equivalent to a 2-point calibration

The code is marked clearly by a label on each stan-

dard probe.

3) [OP2]:Calibration by physical standard references

(1-point, 2-point or 3-point calibration)

CAL = calibration

Push [ENTER/MENUE] to calibrate the instrument

with sensor. Use the up and down keys [



] to

select CAL. Push again [ENTER/MENUE]. On the

left corner of the display appears a small 1, which

indicates the selected channel. For changing the

channel use the up and down keys [



]. Push

[ENTER/MENUE] to confirm.

Use the up and down keys [



] to select the re-

quested calibration option. Push [ENTER/MENUE] to

confirm.

Standard linearization

according DIN IEC 60751 / [oFF

Use the up and down keys [



] to select [oFF.

Push [ENTER/MENUE] to confirm.

Push [ESC] to be back in the measuring mode.

Calibration by code / oP1

Use the up and down keys [



] to select oP1. Push

[ENTER/MENUE] to confirm.

On the bottom of the display appears a very small 1,

after this number a four-digit number (Hex-Code/0..F)

is displayed. For changing the number use the up

key [



]. For stepping to the next number use the

down key [



]. If the requested number is complete

then push [ENTER/MENUE] to confirm. Now on the

bottom of the display appears a very small 2, after

this number a second four-digit number is displayed.

For changing the number please follow the manual

as before. Push [ESC] to be back in the measuring

mode.

Note: After confirming oP1 by pushing [ENTER/

MENUE] the function oP1 (calibration by code) is

activated, even though you leave the menu by press-

ing [ESC].



 CAL

oFF oP1 oP2

Important!

Unit



 MENUE

Prob Lin2 CAL PrEn Chnl ArEA Lo6

DE P700 Anleitung engl. 12/11 06.12.2011 10:04 Uhr Seite 8

Display-indication with active calibration code(OP1):

The CAL -segment and the small 1 on the left indica-

tes to the user that oP1 is activated.

Calibration by physical standard references / oP2

Use the up and down keys [



] to select oP2. Push

[ENTER/MENUE] to confirm.

On the bottom of the display appears 1 P. For chang-

ing between a 1-Point [1 P], 2-Point [2 P] or 3-Point

[3 P] - calibration use the up and down keys [



Example of a 1-Point calibration:

Push [ENTER/MENUE] to confirm. On the display

appears Go. After the displayed measuring value is

stabile push [ENTER/MENUE]. App. 2 seconds later

in the first display line appears P1 (measuring value

1); in the second display line appears dP. (standing

for decimal point).

Use the up and down keys [



] to select the num-

ber of digits after decimal point:

dP. = two decimal digits

dP . = one decimal digit

(decimal point is jumping one digit to the right)

Push [ENTER/MENUE] to confirm. On the second

line of the display appears Si -. Use the up and down

keys [



] to select the requested sign.

Si = reference standard shows

a negative measuring value (below 0,00C°)

Si = reference standard shows

a positive measuring value (above 0,00C°)

Push [ENTER/MENUE] to confirm. On the second

line of the display appears Fd 0.

Use the up and down keys [



] to select the re-

quested range:

Fd 0 = below 100,00°C

Fd 1 = above 100,00°C

Push [ENTER/MENUE] to confirm. On the display

appears 00.00. For changing the value use the up

key [



] . For stepping to the next number use the

down key [



]. If the requested value is complete

then push [ENTER/MENUE] to confirm.

Push [ESC] to be back in the measuring mode.

Note: A break of the physical calibration cannot

be done by the [ESC]-button. Switching off the in-

strument can only do a break of the physical cali-

bration.



 oP2

1 P 2 P 3 P

Important!

DE P700 Anleitung engl. 12/11 06.12.2011 10:04 Uhr Seite 9

Display-indication with active calibration code (OP2):

The CAL-segment and the small 2 on the left indica-

tes to the user that oP2 is activated.

1.4.4.1 Calibration function of the combination

probe (humidity/temperature) [CAL]

Each humidity probe of Dostmann electronic is a

combination probe. That means that beside the

humidity sensor these probes also contain a tempe-

rature sensor. Both measurement values are plug-

ged in the same channel over one probe. Before the

calibrating of both measurement values (humidity

and temperature) the calibrated measurement

value must be adjusted at the menu item Prob

(Probe selection 1.4.2).

The instruments offer three calibration options:

1) [OFF]:Standard characteristic curve (no specific

probes correction will be carried out)

2) [OP1]:Calibration by code (2 x four digit code) is

equivalent to a 2-point calibration

The code is marked clearly by a label on each stan-

dard probe/rH = humidity & P°C = temperature.

3) [OP2]:Calibration by physical standard references

(1-point, 2-point or 3-point calibration) is only for

the measurement value rH humidity possible

CAL = calibration

Push [ENTER/MENUE] to calibrate the instrument

with sensor. Use the up and down keys [



] to

select CAL. Push again [ENTER/MENUE]. On the

left corner of the display appears a small 1, which

indicates the selected channel. For changing the

channel use the up and down keys [



] . Push

[ENTER/MENUE] to confirm.

With the up and down keys [



] you can now choo-

se between rH for calibration of humidity and P°C for

calibration of temperature.

Use the up and down keys [



] to select the reque-

sted calibration option. Push [ENTER/MENUE] to

confirm.



 CAL

rH P °C

Unit



 MENUE

Prob Lin2 CAL PrEn Chnl ArEA Lo6

DE P700 Anleitung engl. 12/11 06.12.2011 10:04 Uhr Seite 10

Andere Handbücher für P705

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dostmann Electronic Messgerät Handbücher

Dostmann Electronic

Dostmann Electronic P700-EX Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic HumidCheck Pro Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic MS 85 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic OXY 7 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic PH CHECK 5040-0301 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic MS 83 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic P700-EX Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic TC 301 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic Air CO2ntrol 3000 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic Air Co2ntrol 5000 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic MS 82 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic P700 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic DEC91 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic GD 383 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic P400 Series Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic 5020-0322 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic VA893 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic HumidCheck Pro Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic P795 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic P4000 Series Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic DewPoint Pro H560 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic P705 Installationshandbuch

Dostmann Electronic

Dostmann Electronic 5020-0343 Bedienungsanleitung

Dostmann Electronic

Dostmann Electronic 31.5008.02 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung