DPS Telecom Remote Status Panel Bedienungsanleitung
USER MANUAL
Remote Status Panel for NetGuardian
August 17, 2010
Visit our website at www.dpstelecom.com for the latest PDF manual and FAQs.
D-OC-UM108.17100 Firmware Version 1.0A
© 2010 DPS Telecom
This document contains proprietary information which is protected by copyright. All rights are reserved. No part of this
document may be photocopied without prior written consent of DPS Telecom.
All software and manuals are copyrighted by DPS Telecom. Said software and manuals may not be reproduced, copied,
transmitted or used to make a derivative work, by either mechanical, electronic or any other means in whole or in part,
without prior written consent from DPS Telecom, except as required by United States copyright laws.
The material in this manual is for information purposes and is subject to change without notice. DPS Telecom shall not be
liable for errors contained herein or consequential damages in connection with the furnishing, performance, or use of this
manual.
Notice
August 17, 2010
Revision History
Initial release
ContentsVisit our website at www.dpstelecom.com for the latest PDF manual and FAQs
Overview: Remote Status Panel for NetGuardian1 1
Shipping List2 2
Specifications3 3
Installation4 4
Tools Needed4.1 4
Wall Mounting4.2 4
Power Connection4.3 5
NetGuardian Port4.4 6
Craft Port4.5 6
Visual Display5 6
Remote Status Panel Status LEDs5.1 7
Audible Alarm and ACK Button6 8
Craft Port and Firmware Upgrades7 8
Technical Support8 9
1
Overview: Remote Status Panel for NetGuardian1
Remote Status Panel
The Remote Status Panel for NetGuardian is an annunciation device that displays operational status of the
NetGuardian and Expansion Unit The connected NetGuardian completely controls the audiovisual display of the
Remote Status Panel, which only responds to the servers' commands.
The front panel features six large bi-color (red and green) LEDs. Once provisioned, the LEDs will display red
when alarms occur and the speaker will sound.
The speaker can be silenced by OFF command from the NetGuardian or the ACK (Acknowledge/momentarily
silence) button on the front of the unit.
2
Shipping List2
Please make sure all of the following items are included with your Remote Status Panel. If parts are missing, or if
you ever need to order new parts, please refer to the part numbers listed and call DPS Telecom at
1-800-622-3314.
Remote Status Panel for NetGuardian
D-PK-RSPNG
Remote Status Panel User Manual DB9M-DB9F Download Cable 6 ft.
D-OC-UM108.17100 D-PR-045-10-A-04
x2 x4
2 Wall Mount Brackets 4 Wall Mount Bracket Screws
x4 x4
Four Rack Screws Four Metric Rack Screws
x2 x2
Two Power Connector Plugs Two 1/2-Amp GMT Fuses
RJ12 to RJ45 Connection Cable RJ45 to RJ45 Connection Cable
D-PR-1033-10A-01 D-PR-1028-10C-01
(for connection to NetGuardian DX) (for connection to NetGuardian)
3
Specifications3
Dimensions: 6.136" H x 17" W x 1.2" D (15.5 cm x 43.2 cm x 3.05 cm)
Mounting: Wall mount
Power Input: –48 VDC dual power inputs (–40 VDC to –70 VDC)
Fuse: 1/2 Amp GMT
Current Draw: 250mA
Protocols: DCPx
Interfaces: 1RJ45 RS232 port
1 DB9 Craft port
Visual Interface: 5bicolor (red and green) NetGuardian status LEDs
2 Remote Status Panel NetGuardian status LEDs
Audible Notification: Alarm speaker with ACK (momentarily silence) button
Operating Temperature: 35°–140° F (1.67°–60° C)
Operating Humidity: 0%–95% noncondensing
4
Installation4
Tools Needed4.1
To install the Remote Status Panel, you'll need the following tools:
Phillips No. 2 Screwdriver Small Standard No. 2 Screwdriver
Wall Mounting4.2
The Remote Status Panel can be flush or rear-mounted
The Remote Status Panel is wall mounted using the 2 wall mount brackets supplied with the unit. Attach the
brackets in the wall mount locations shown here.
5
Power Connection4.3
Power connectors and fuses
The Remote Status Panel has two screw terminal barrier plug power connectors, located on the left side of the
back panel.
Before you connect a power supply to the Remote Status Panel, test the voltage of your power supply:
·Connect the black common lead of a voltmeter to the ground terminal of the battery, and connect the red
lead of the voltmeter to the battery's –48 VDC terminal. The voltmeter should read between –43 and –53
VDC. If the reading is outside this range, test the power supply.
To connect the Remote Status Panel to a power supply, follow these steps:
1. Remove the fuses from the back panel. Do not reinsert the fuse until all power connections have
been made.
2. To ground the Remote Status Panel, connect a grounding wire to the grounding lug.
3. Remove the power connector plug from Power Connector A. Note that the plug can be inserted into the
power connector only one way — this ensures that the barrier plug can only be reinserted with the
correct polarity. Note that the –48V terminal is on the left and the GND terminal is on the right.
4. Insert a battery ground into the power connector plug's right terminal and tighten the screw; then
insert a –48 VDC line to the plug's left terminal and tighten its screw.
5. Push the power connector plug firmly back into the power connector. If the power feed is connected
correctly, the LED by the connector will light GREEN and the Remote Status Panel will power up. If
the polarity of the power feed is reversed, the LED by the power connector will light RED and the
Remote Status Panel will NOT power up — you won't see any other LEDs light or hear any sounds
from the unit. Reversing the polarity does not harm the unit, but you should immediately remove the
fuse and reconnect the power leads correctly.
6. Repeat Steps 3–5 for Power Connector B.
7. Reinsert the fuse to power the Remote Status Panel.
When power up is complete, the front panel Power LED will light GREEN.
6
NetGuardian Port4.4
Connect the NetGuardian that will control the Remote Status Panel to the RJ45 NetGuardian port on the right
side of the back panel. The pinout for this port is shown below.
NetGuardian port pinout
Craft Port4.5
Use the front panel craft port only when a firmware upgrade is required. No provisioning of the unit
should be required. To upgrade firmware, connect the included DB9 download cable from your PC's
COM port to the craft port. Pinout is shown here.
12345
TX
GND
6789
CTS
Pin # Signal Description
1Not connected
2TX Transmit data
3
4
5GND Ground
6Not connected
7CTS Clear to send
8
9Not connected
Recieve Data
Not connected
Request to send
DB9 RS-232
RTS
RX
RTS
RX
Visual Display5
The Remote Status Panel's visual displays are completely controlled by commands from the connected
NetGuardian.
Each one of the LEDs can be associated to alarm points. If there is an active alarm, the LED will be red. If there
are no alarms, the LED will be off. A blinking LED means there was a change of state for the alarm point the
LED was associated with.
Inhaltsverzeichnis
Andere DPS Telecom Netzwerk-Hardware Handbücher
DPS Telecom
DPS Telecom T/Mon NOC Bedienungsanleitung
DPS Telecom
DPS Telecom DAC-P Bedienungsanleitung
DPS Telecom
DPS Telecom NetGuardian 832A Bedienungsanleitung
DPS Telecom
DPS Telecom NetGuardian ENV Bedienungsanleitung
DPS Telecom
DPS Telecom ECU LAN Bedienungsanleitung
DPS Telecom
DPS Telecom NetGuardian 240T Gebrauchsanweisung
DPS Telecom
DPS Telecom NetGuardian 420 Bedienungsanleitung
DPS Telecom
DPS Telecom T/Mon/IAM Bedienungsanleitung
DPS Telecom
DPS Telecom HVAC Controller G3 Bedienungsanleitung
DPS Telecom
DPS Telecom NetGuardian 832A G5 Bedienungsanleitung
DPS Telecom
DPS Telecom NetGuardian 16A Bedienungsanleitung
DPS Telecom
DPS Telecom NetGuardian 216 G4 Bedienungsanleitung
DPS Telecom
DPS Telecom NetGuardian 832/864A Bedienungsanleitung
DPS Telecom
DPS Telecom NetGuardian 216F Bedienungsanleitung
DPS Telecom
DPS Telecom NetGuardian 832A Bedienungsanleitung
DPS Telecom
DPS Telecom Net Dog 82 IP Bedienungsanleitung
DPS Telecom
DPS Telecom NetGuardian BSM Bedienungsanleitung
DPS Telecom
DPS Telecom NetGuardian 832A Bedienungsanleitung
DPS Telecom
DPS Telecom CellVoice 16 Bedienungsanleitung
DPS Telecom
DPS Telecom NetGuardian 480 G3 Bedienungsanleitung
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
