Dräger Alcotest 5820 Bedienungsanleitung
i
Dräger Alcotest 5820
WARNING
Strictly follow the Instructions for Use.
The user must fully understand and strictly observe the instructions.
Use the product only for the purposes specified in the Intended use
section of this document.
!
enUS Instructions for use
3
fr Notice d’utilisation
18
es Instrucciones de uso
33
2
OK
1
9
2
3
4
7
8
6
14
5
00133580.eps
11
13
10
12
For description of device parts, please
voir « Description », page 4
Pour obtenir une description des pièces,
voir « Description », page 19
Para la descripción de las piezas del
aparato, consulte voir « Descripción »,
page 34
en
fr
es
For your safety
3
en
1 For your safety
1.1 General safety notes
Before using this product, carefully read the Instructions for Use.
Strictly follow the Instructions for Use. The user must fully understand
and strictly observe the instructions. Use the product only for the
purposes specified in the Intended use section of this document.
Do not dispose of the Instructions for Use. Ensure that it is retained
and appropriately used by the product user.
Comply with all local and national rules and regulations associated
with this product.
Only trained and competent personnel are permitted to inspect,
repair and service the product. Dräger recommend a Dräger
service contract for all maintenance activities and that all repairs
are carried out by Dräger.
Do not use a faulty or incomplete product. Do not modify the product.
Notify Dräger in the event of any component fault or failure.
2 Conventions used in this document
2.1 Definitions of alert icons
The following alert icons are used in this document to provide and
highlight areas of the associated text that require a greater awareness
by the user. A definition of the meaning of each icon is as follows:
WARNING
Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
Description
4
en
2.2 Typographical conventions
This symbol indicates information which facilitates the use of the
product.
3 Description
3.1 Product overview
1 Breath-alcohol-analyzer
2 button (switch instrument on/off; confirm inputs)
3 button (open menu; set value)
4 LEDs
5 Mouthpiece receptacle (configurable: right or left)
6 Display
7 button (set value)
8 USB connection (Important: Not for charging the device, for
Service only)
9 Wrist strap
10 Battery compartment cover
11 Battery
12 Pull strap for battery replacement
13 Loudspeaker (Important: Not reset button)
14 Mouthpiece
3.2 Intended use
The Dräger Alcotest® 58201) is used for measuring the alcohol
concentration in the breath of a human. The measurement is used as
an indication for alcohol intoxication. Based on the measurement
results no therapeutic measures should be initiated.
1) Alcotest is a registered trademark of Dräger.
Use
5
en
4 Use
WARNING
Small parts of the device can come loose and be swallowed.
► Keep the device out of reach of children under the age of 3.
4.1 Prerequisites
The instrument is factory-calibrated when delivered. If the calibration
date has exceeded12 months, the instrument should be adjusted, e.g.
by DrägerService. It is still possible to use the device, even if the
calibration period is exceeded. After the last alcohol intake, wait
approx. 15 minutes before a measurement is carried out. Residual
mouth-alcohol may cause incorrect measuring results. This may also
occur by aromatic drinks (e.g. fruit juices), alcoholic mouth sprays,
medicines and drops, as well as by burping and vomiting. Rinsing the
mouth with water or non-alcoholic drinks does not replace the wait
time!
4.2 Initial start-up
A quick setup process (“wizard”) starts when the instrument is
switched on for the first time. This step is not required for
pre-configured instruments.
The following settings are accessible using the wizard:
Language
Date format
Date
Time format
Time
Measuring unit
All settings can be changed later on via the menu.
Use
6
en
4.3 Carrying out an automatic breath test
A new mouthpiece must be inserted for each new person who
provides a breath test.
Do not allow any high alcohol concentrations on the sensor, e.g.
by rinsing the mouth with a high proof alcohol shortly before the
measurement, as this will shorten the service life of the sensor.
1. Remove mouthpiece (order no. 68 10 690 “Standard”, 68 11 055
“with back valve”)
2. For reasons of hygiene, leave the protective wrapping around the
mouth contact area. Open the packaging at the perforation and
take off the protective wrapping only around the attachment area
of the mouthpiece.
3. Attach the mouthpiece at an angle to the mouthpiece receptacle.
4. Press it into the receptacle. The fluted markings (press-on surface)
on the mouthpiece faces upwards while this is done. The
mouthpiece audibly snaps into place (see page 2).
5. Remove all packaging.
6. Keep the button pressed for approx.1 second until the startup
screen is displayed. An optional self-test is carried out.
7. After approx. 4 seconds the display shows READY and the
instrument is now ready to test. Take a deep breath and blow
evenly and without interruptions into the mouthpiece as long as
possible. A progress bar is displayed. An adequate breath flow is
confirmed by a continuous tone.
8. Without any further action from user side, the device takes
automatically a test sample at the end of the breath of the test
subject.
9. The continuous tone is muted directly afterwards which gives the
signal that the test subject can stop with blowing. The test result is
displayed with date and time after 5 to 25 seconds (depending on
the instrument temperature and the measured concentration).
In case of a negative alcohol test, 0,00 will be displayed.
Use
7
en
In case of a positive alcohol test, the measured alcohol level will be
displayed.
To perform a new measurement, press the button.
After the sensor‘s short recovery time, (see "Technical data" on
page 15) READY will be displayed and the device is ready to use
again.
4.4 Performing a manual breath test (optional)
If the test subject cannot provide the required minimum volume, the
sampling of breath can be triggered manually.
1. Preparation as for the automatic breath test (see chapter 4.3 on
page 6).
2. If the progress bar is displayed after breath flow is detected, tap
the button.
In the results display, MANUAL is also displayed.
4.5 Performing a passive breath test (optional)
With passive sampling, the sampling is initiated manually by the
instrument user. The passive test must be done without an attached
mouthpiece. Possible applications include the testing of ambient air or
the breath of persons for the presence of alcohol. To perform a passive
test:
1. Keep the button pressed for approx.1 second until the startup
screen appears.
2. Hold the instrument into the air to be analyzed without a
mouthpiece.
3. Briefly press the button to initiate the measurement.
The device will take a test sample at that very moment and will
start analyzing.
In the results display, PASSIVE is also displayed. If no alcohol is
detected, the No Alcohol will be displayed and the LED will be green.
In case alcohol is detected, Alcohol will be displayed and the LED will
be red.
Use
8
en
4.6 Switching off the Instrument
The instrument will switch off after pressing the button for approx. 3
seconds. A switch-off count down will be shown as well. If the display
is off, stop pressing the button. Otherwise the device will be switched
on again.
The instrument will switch off automatically after approx. 4 minutes
without any activity.
Switching off the instrument does not reduce the post-test
waiting period before you can perform another test.
4.7 Removing the mouthpiece
1. Push the mouthpiece upwards out of the mouthpiece receptacle.
2. Dispose of the mouthpiece in accordance with local regulations.
Do not reuse a mouthpiece.
4.8 Settings/information
Start the device pressing until READY is displayed.
To enter the device menu, press the button.
In the main menu all menu options are listed one below the other.
To navigate within the options list and select a menu option:
1. Press or button to mark the respective menu option with the
cursor.
2. Confirm the selected menu option with the button.
Use
9
en
The following table provides an overview of the menu options and how
to use them:
Menu option Description Interaction
instruction
Measuring Option to leave the
menu and to go back to
the READY screen to
perform a test.
press to leave
the menu and
prepare for
measuring
Results Overview of the last
tests performed on the
device (incl. result,
date, time, test ID).
There is one test dis-
played per screen.
press to enter
the menu
press or to
navigate through
the list
Date/Time Date: to set the date
Time: to set the time
Date format: to choose
a format (yyyy/mm/dd,
yyyy-mm-dd, mm/dd/
yyyy, dd.mm.yyyy)
Time format: to choose
a format (12 or 24)
press to enter
the menu
press or to
navigate through
the list
press to select
the option
change a setting or
number by
pressing or
press to
confirm, the
submenu will be
displayed again
select Back to
leave the submenu
Use
10
en
Contrast The display contrast
can be adjusted within
5 levels.
press to enter
the menu
change the setting
by pressing or
press to
confirm
Speaker Any acoustic signals of
the device can be
turned off or to a
volume of 50% or
100%.
press to enter
the menu
change the setting
by pressing or
Language The language of the
display can be
adjusted.
press to enter
the menu
choose the
language by
pressing or
press to
confirm
Meas. unit The measurement
results can be
displayed in the
following units: %, ‰,
g/L, mg/100 mL, mg%,
mg/mL, mg/L, μg/100
mL, μg%, μg/L, g/210
L.
press to enter
the menu
choose the unit by
pressing or
press to
confirm
Software Version Software version and
part number are
displayed.
press to enter
or leave the menu
Menu option Description Interaction
instruction
Andere Handbücher für Alcotest 5820
1
Inhaltsverzeichnis
Sprachen:
Andere Dräger Messgerät Handbücher
Dräger
Dräger Interlock 5000 Bedienungsanleitung
Dräger
Dräger Bodyguard 7000 Bedienungsanleitung
Dräger
Dräger FG4200 Bedienungsanleitung
Dräger
Dräger JM-105 Bedienungsanleitung
Dräger
Dräger Alcotest 6510 Bedienungsanleitung
Dräger
Dräger DrugTest 5000 Bedienungsanleitung
Dräger
Dräger Tube Ethylene glycol 10 Bedienungsanleitung
Dräger
Dräger PIR 3000 Bedienungsanleitung
Dräger
Dräger REGARD Bedienungsanleitung
Dräger
Dräger X-zone 5500 Bedienungsanleitung
Dräger
Dräger Interlock 7500 DVI Bedienungsanleitung
Dräger
Dräger PX4500 Bedienungsanleitung
Dräger
Dräger Polytron RC001 Bedienungsanleitung
Dräger
Dräger X-AM 2500 Bedienungsanleitung
Dräger
Dräger X-node Bedienungsanleitung
Dräger
Dräger X-am 1/2/5000 Bedienungsanleitung
Dräger
Dräger X-AM 2500 Bedienungsanleitung
Dräger
Dräger Interlock 7000 Bedienungsanleitung
Dräger
Dräger Polytron 8000 Series Bedienungsanleitung
Dräger
Dräger Vitalert 3000 Series Bedienungs- und Sicherheitshinweise
