Dräger Fabius GS SW 1.3n Technische Daten

Breathing system heater

Fabius®GS SW 1.3n (90 37 781)

Fabius®GS SW 2.n (90 37 933)

Fabius®GS SW 3.n (90 38 685)

Fabius®Tiro SW 2.n (90 38 132)

Fabius®Tiro SW 3.n (90 38 686)

Fabius®GS premium SW 3.n (90 38 923)

Fabius®plus SW 3.n (90 39 054)

Supplement to Operator’s Instruction Manuals

Contents

2Fabius GS/Tiro Supplement

Contents

For Your Safety and that of Your Patients .................................................................. 3

Purpose of This Document ........................................................................................ 4

Breathing System Heater (Optional) ....................................................................... 4

Symbol Definition ....................................................................................................... 5

General Warnings and Cautions ................................................................................ 6

Installation of BSHPS (Fabius GS) ............................................................................ 7

Installation of BSHPS (Fabius Tiro) ........................................................................... 9

Operation of BSHPS ................................................................................................ 14

Switching Off BSHPS ............................................................................................... 16

Preparing the Compact Breathing System for Disinfection and Cleaning ................ 16

BSHPS Technical Data ............................................................................................ 18

Daily Checkout ......................................................................................................... 19

For Your Safety and that of Your Patients

Fabius GS/Tiro Supplement 3

For Your Safety and that of Your

Patients

Strictly follow the Instructions for Use

Any use of the breathing system heater requires full

understanding and strict observation of these

instructions and the Fabius GS or Fabius Tiro

Operator's Instruction Manual. The apparatus is only

to be used for purposes specified here.

Safe connection with other electrical equipment

Electrical connections to equipment which is not

listed in these Instructions for Use should only be

made following consultations with the respective

manufacturers or an expert.

Not for use in areas of explosion hazard

This apparatus is neither approved nor certified for

use in areas where combustible or explosive gas

mixtures are likely to occur.

Liability for proper function or damage

The liability for the proper function of the apparatus is

irrevocably transferred to the owner or operator to

the extent that the apparatus is serviced or repaired

by personnel not employed or authorized by

DrägerService or if the apparatus is used in a

manner not conforming to its intended use.

Dräger cannot be held responsible for damage

caused by non-compliance with the

recommendations given above. The warranty and

liability provisions of the terms of sale and delivery of

are likewise not modified by the recommendations

given above.

Dräger Medical GmbH

Purpose of This Document

4Fabius GS/Tiro Supplement

Purpose of This Document

Breathing System Heater (Optional)

Breathing system heater for use in conjunction with

the Fabius GS and Fabius Tiro anaesthetic machines

in order to reduce the condensation of moisture in

the breathing system during low-flow operation (fresh

gas flow below 1 l/min).

This Instruction Manual supplement contains

additions to the information contained in the Fabius

GS or Fabius Tiro Operator's Instruction Manual.

Symbol Definition

Fabius GS/Tiro Supplement 5

Symbol Definition

The following symbols appear on the power supply of

the (optional) breathing system heater.

Caution: Refer to accompanying documents

before operating equipment.

Caution: Risk of electric shock, do not remove

cover. Refer servicing to a

DrägerService representative.

Degree of protection against electric shock:

Class 1 Type B.

Registration Mark

Mains Applied/Mains Power

Fuse

Heater Power

DC Voltage

AC Voltage

CUS

General Warnings and Cautions

6Fabius GS/Tiro Supplement

General Warnings and Cautions

The following list of warnings and cautions apply to

general operation and maintenance of the Fabius GS

and Fabius Tiro. Warnings and cautions about

installing and operating specific parts appear with

those topics.

• A Warning statement gives important

information that, if ignored, could lead directly

to personal injury.

• A Caution statement gives important

information that, if ignored, could lead directly

to equipment damage and indirectly to

personal injury.

Warning: When the moisture content falls below a

specified minimum level, the following

undesirable reactions can occur,

regardless of the type of CO2absorbent

and the anaesthetic agent used, e.g.

Halothane, Enflurane, Isoflurane,

Sevoflurane or Desflurane:

• reduced CO2absorption,

• formation of CO,

• absorption and/or decomposition of

the inhalation anaesthetic agent,

• increased heat generation in the

absorber, leading to higher breathing

gas temperatures.

Additionally, the breakdown products of

anaesthetic agents exposed to dry

absorbent are both flammable and toxic,

and fires have been reported in

association with the use of desiccated

absorbent and volatile anaesthetics.

These reactions can result in danger to

the patient in the form of CO intoxication,

insufficient depth of anesthesia and

airway burns.

Installation of BSHPS (Fabius GS)

Fabius GS/Tiro Supplement 7

Installation of BSHPS (Fabius GS)

The following provides instruction on installation of

the power supply for the breathing system heater

(mains adapter).

Figure 1. BSHPS Installation on Machine with Left Mount

COSY

Left Mount COSY BSHPS Installation

The following numbers in boldface refer to Figure 1.

1. Install the power supply onto the left rear GCX

rail of the Fabius GS by sliding the mounting

plate of the power supply through the opening of

the rail (1) and then sliding it upward. Tighten the

knob (2) against the rail when the power supply

is in the desired position.

2. Route the power cable (3) for the heater below

and behind the power supply and then up to the

rear of the COSY arm. Push the cable into the

cable management cavity (4) on the bottom of

the COSY arm.

3. Plug the connector at the end of the cable into

the mating connector (5) on the rear underside of

the COSY. Orient the connector so that the red

mark on the connector plug aligns with the red

mark on the receptacle.

Installation of BSHPS (Fabius GS)

8Fabius GS/Tiro Supplement

Figure 2. BSHPS Installation on Machine with Right Mount

COSY - Step 1

Right Mount COSY BSHPS Installation

1. Install the power supply onto the left rear GCX

rail of the Fabius GS by sliding the mounting

plate of the power supply through the opening of

the rail (1in Figure 1) and then sliding it upward.

Tighten the knob (1in Figure 2) against the rail

when the power supply is in the desired position.

2. Route the power cable for the heater through the

trough (2in Figure 2) on the rear of the cabinet.

At the right hand end of the trough, route the

cable into the cable management cavity

(1in Figure 3) on the bottom of the COSY arm.

Figure 3. BSHPS Installation on Machine with Right Mount

COSY - Step 2

3. Plug the connector at the end of the cable into

the mating connector (2in Figure 3) on the rear

underside of the COSY. Orient the connector so

that the red mark on the connector plug aligns

with the red mark on the receptacle.

Installation of BSHPS (Fabius Tiro)

Fabius GS/Tiro Supplement 9

Installation of BSHPS (Fabius Tiro)

The following provides instruction on installation of

the Breathing System Heater Power Supply

(BSHPS).

Figure 4. BSHPS Installation on Machine with Left Mount

COSY (Trolley)

Left Mount COSY BSHPS Installation

(Trolley)

The following numbers in boldface refer to Figure 4.

1. Install the power supply onto the left rear GCX

rail of the Fabius Tiro by sliding the mounting

plate of the power supply through the opening of

the rail (1) and then sliding it upward. Tighten the

knob (2) against the rail when the power supply

is in the desired position.

2. Route the power cable (3) for the heater below

and behind the power supply and then up to the

rear of the COSY arm. Push the cable into the

cable management cavity (4) on the bottom of

the COSY arm.

3. Plug the connector at the end of the cable into

the mating connector (5) on the rear underside of

the COSY. Orient the connector so that the red

mark on the connector plug aligns with the red

mark on the receptacle.

Installation of BSHPS (Fabius Tiro)

10 Fabius GS/Tiro Supplement

Figure 5. BSHPS Installation on Machine with Right Mount

COSY - Step 1 (Trolley)

Right Mount COSY BSHPS Installation

(Trolley)

1. Install the power supply onto the left rear GCX

rail of the Fabius Tiro by sliding the mounting

plate of the power supply through the opening of

the rail (1in Figure 4) and then sliding it upward.

Tighten the knob (1in Figure 5) against the rail

when the power supply is in the desired position.

2. Route the power cable for the heater through the

trough (2in Figure 5) on the rear of the cabinet.

At the right hand end of the trough, route the

cable into the cable management cavity

(1in Figure 6) on the bottom of the COSY arm.

Figure 6. BSHPS Installation on Machine with Right Mount

COSY - Step 2 (Trolley)

3. Plug the connector at the end of the cable into

the mating connector (2in Figure 6) on the rear

underside of the COSY. Orient the connector so

that the red mark on the connector plug aligns

with the red mark on the receptacle.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dräger Medizinische Geräte Handbücher

Dräger

Dräger BiliLux Bedienungsanleitung

Dräger

Dräger JM-105 Bedienungsanleitung

Dräger

Dräger X-plore 8000 Bedienungsanleitung

Dräger

Dräger Infinity Acute Care System Evita Infinity... Bedienungsanleitung

Dräger

Dräger Oxylog 2000 plus Bedienungsanleitung

Dräger

Dräger Vapor 19.n Bedienungsanleitung

Dräger

Dräger Julian Bedienungsanleitung

Dräger

Dräger Polaris 600 Bedienungsanleitung

Dräger

Dräger VITALERT 2000 Montageanleitung

Dräger

Dräger EVITA XL Gebrauchsanweisung

Dräger

Dräger PressurePod Bedienungsanleitung

Dräger

Dräger Julian Bedienungsanleitung

Dräger

Dräger X-plore 5500 Bedienungsanleitung

Dräger

Dräger Infinity Acute Care System Evita Infinity... Bedienungsanleitung

Dräger

Dräger Polaris 50 Bedienungsanleitung

Dräger

Dräger BiliLux Bedienungsanleitung

Dräger

Dräger Draeger-Tube Mercaptan 20/a Bedienungsanleitung

Dräger

Dräger Babylog 8000 plus Bedienungsanleitung

Dräger

Dräger Evita 2 Dura Bedienungsanleitung

Dräger

Dräger Evita 2 Bedienungsanleitung

Dräger

Dräger PSS 7000 S Series Bedienungsanleitung

Dräger

Dräger Evita V800 Bedienungsanleitung

Dräger

Dräger Care-For-Me MU06943 Bedienungsanleitung

Dräger

Dräger Oxy 3000 Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung