Draytek Vigor2500 series Bedienungsanleitung

ADSL Routers

Annex A / Annex B

ISDN Backup

Wireless AP

Vigpr2500 Vigpr2500We Vigpr2500Wt

The Vigor2500 series is an Internet access solution for your LAN which not only provides shared

web surfing but countless other value-added features such as security, VPN and multimedia support,

all in a reliable one-box solution.

LED Indicators

and Back Panels

Each of the Vigor2500 series router has different front and rear panels. Before

you begin to install, please take a moment to become more familiar with the

LEDindicators and rear panels. The following sections describe the models

individually.

Vigor2500

*/*

series introduction

Vigor2500

LED Indicators Descriptions

ACT(Activity)

ADSL

Blink when power is supplied to the router and the router is running normally.

LINE

DATA

ON when the ADSL network is correctly setup

Blinking indicates the DSL protocols start handshaking.The light will

remain still when data transmission is available.

Back Panels Descriptions

LAN 1-4

Link

100Mbps

Local Area Network port status. A steady LED indicates a

connection between computers on your LAN. A flickering LED

indicates data transmission.

Speed status of the Ethernet connection. A steady LED indicates

100Mbps speed. If the Link light is on and the 100Mbps light is off,

the speed is 10Mbps.

VPN VPN connection status. A steady LED indicates VPN connection is up.

ON/OFF

PWR

ON / turn on power. OFF / switch off the power.

Only the power adapter comes with the package can be connected

to the AC 9V power jack.

To connect Vigor 2500 to an electrical outlet.

P1,P2,P3,P4 These switch ports should be connected to your local PCs.

ADSL To connect the ADSL cable to your telephone jack.

Factory Reset

The restore default settings: While the router is running (ACT LED blinking), press the

button and hold for more than five seconds. The ACT LED begins to blink rapidly, then

release the button . The router will restart with the factory default configuration.

Vigor2500We

LED Indicators Descriptions

ACT(Activity)

ADSL

Blink when power is supplied to the router and the router is running normally.

LINE

DATA

ON when the ADSL network is correctly setup

Blinking indicates the DSL protocols start handshaking.The light will

remain still when data transmission is available.

Descriptions

LAN 1-4

Link

100Mbps

Local Area Network port status. A steady LED indicates a

connection between computers on your LAN. A flickering LED

indicates data transmission.

Speed status of the Ethernet connection. A steady LED indicates

100Mbps speed. If the Link light is on and the 100Mbps light is off,

the speed is 10Mbps.

VPN

VPN connection status. A steady LED indicates VPN connection is up.

ON when the wireless LAN is ready.A flickering LED indicates data transmission.

ON/OFF

PWR

ON / turn on power. OFF / switch off the power.

Only the power adapter comes with the package can be connected

to the AC 9V power jack.

To connect Vigor 2500We to an electrical outlet.

P1,P2,P3,P4 These switch ports should be connected to your local PCs.

ADSL To connect the ADSL cable to your telephone jack.

Factory Reset

The restore default settings: While the router is running (ACT LED blinking), press the

button and hold for more than five seconds. The ACT LED begins to blink rapidly, then

release the button . The router will restart with the factory default configuration.

Back Panels

Vigor2500Wt

LED Indicators Descriptions

ACT(Activity)

ADSL

Blink when power is supplied to the router and the router is running normally.

LINE

DATA

ON when the ADSL network is correctly setup

Blinking indicates the DSL protocols start handshaking.The light will

remain still when data transmission is available.

Descriptions

LAN 1-4

Link

100Mbps

Local Area Network port status. A steady LED indicates a

connection between computers on your LAN. A flickering LED

indicates data transmission.

Speed status of the Ethernet connection. A steady LED indicates

100Mbps speed. If the Link light is on and the 100Mbps light is off,

the speed is 10Mbps.

VPN

VPN connection status. A steady LED indicates VPN connection is up.

ON when the wireless LAN is ready.A flickering LED indicates data transmission.

ON/OFF

PWR

ON / turn on power. OFF / switch off the power.

Only the power adapter comes with the package can be connected

to the AC 9V power jack.

To connect Vigor 2500Wt to an electrical outlet.

P1,P2,P3,P4 These switch ports should be connected to your local PCs.

ADSL To connect the ADSL cable to your telephone jack.

Factory Reset

The restore default settings: While the router is running (ACT LED blinking), press the

button and hold for more than five seconds. The ACT LED begins to blink rapidly, then

release the button . The router will restart with the factory default configuration.

Back Panels

Declarations

protected by copyright. No part may be reproduced, transmitted, transcribed, stored

in a retrieval system, or translated into any language without written permission from

the copyright holders.

The following trademarks are used in this document:

. Microsoft is a registered trademark of Microsoft Corp.

. Windows,Windows 95, 98, Me, NT, 2000, XP and Explorer are trademarks of

Microsoft Corp.

. Apple and Mac OS are registered trademarks of Apple Computer Inc.

Other products may be trademarks or registered trademarks of their respective

manufacturers.

Trademarks

Safety Instructions

Warranty

. Read the installation guide thoroughly before you set up the router.

. The router is a complicated electronic unit that may be repaired only be authorized

and qualified personnel.Do not try to open or repair the router yourself.

. Do not place the router in a damp or humid place, e.g. a bathroom.

. The router should be used in a sheltered area, within a temperature range of +5 to +40

Celsius.

. Do not expose the router to direct sunlight or other heat sources. The housing and

electronic components may be damaged by direct sunlight or heat sources.

. Keep the package out of reach of children.

. When you want to dispose of the router, please follow local regulations on

conservation of the environment.

We warrant to the original end user (purchaser) that the router wil be free from any

defects in workmanship or materials for a period of three (3) years from the date of

purchase from the dealer. Please keep your purchase receipt in a safe place as it

serves as proof of date of purchase. During the warranty period, and upon proof of

purchase, should the product have indications of failure due to faulty workmanship

and/or materials, we will, at our discretion, repair or replace the defective products

or components, without charge for either parts or labor, to whatever extent we

deem necessary tore-store the product to proper operating condition. Any

replacement will consist of a new or re-manufactured functionally equivalent product

of equal value, and will be offered solely at our discretion. This warranty will not

apply if the product is modified, misused, tampered with, damaged by an act of God,

or subjected to abnormal working conditions. The warranty does not cover the

bundled or licensed software of other vendors.Defects which do not significantly

affect the usability of the product will not be covered by the warranty.We reserve

the right to revise the manual and online documentation and to make changes

from time to time in the contents hereof without obligation to notify any person of

such revision or changes.

European Community

Be A Registered

Owner

Firmware & Tools

Updates

Hereby, we declare that the router is in compliance with the essential requirements

and other relevant provisions of R&TTE Directive 99/5/EC.

Web registration is preferred. You can register your Vigor router via http://

www.draytek.com.tw .Alternatively, fill in the registration card and mail it to the

address found on the reverse side of the card.

Due to the continuous evolution of DrayTekADSL & Router technology, all

routers will be regularly upgraded. Please consult theDrayTek web site for more

information on newest firmware, tools and documents.

http://www.draytek.com.tw

Series Quick Start Guide

Identify your variant

Delivery check

Aim of this

chapter

Quickly connect your router to the Internet

Check your router package for the following items :

The Router

1 printed Quick Start Guide with warranty/ registration card

1 CDincludes detailed User Manual in electronic form, released firmware and

utilities

1 AC/DC power supply adapter (black)

1 Ethernet LAN cable (blue) for connection to a computer or hub

1 ADSL line cable (RJ-11 or RJ-45, black)

1 external antenna for Vigor2500We/Wt

Your router package should contain all these items. If any item is

missing or damaged, contact your dealer or our Customer Service

Department immediately.

The Vigor2500 series all containAnnexA/Annex B models,

please check if the package is suitble for your using.

You can get the information from bottom of Vigor2500

series router.

Annex A : connecting to an analog POTS line

Annex B : connecting to a digital ISDN line

Vigor2500

What you

need from ISP

DSL Parameters

It should provide at least the following information from ISP :

1. The VPI/VCI of the virtual channel to use on theDSL line

2. Protocol : PPPoE, PPPoA or MPoA (RFC1483/2684)

3. Encapsulation Method : LLC/SNAP or VCMUX

4. Modulation Method : T1.413,G.lite, G.DMT

DSL line

Depending on the variant Vigor2500 series you purchased, the following DSL

service must be available at your local premisses:

ADSL/POTS : ADSL service must be enabled on your POTS telephone line.

ADSL/ISDN : ADSL service must be enabled on your ISDN telephone line.

(Vgior2500 series provides multimode which can automatically detect)

Local networking

To use the Ethernet port(s) you need at least:

One PC with an Ethernet Card installed.

TCP/IP protocol suite

For TCP/IP, your PC can set either static IP or DHCP to ask IP from router. The

default gateway of router is 192.168.1.1. If static IP is chosen, you can set

192.168.1.x for your PC.

A Web browser

Example:

VPI/VCI = 0/33

Protocol = PPPoA

Encapsulation Method = VCMUX

Modulation Method = G.DMT

Username/Password

Only for PPPoE/PPPoA mode users

Fixed IP Address/ Subnet Mask/ Gateway IP Address

Only for MPoAmode users. Some ISP will use DHCP method to provide IP

address for MPoAmode users, then users do not need to know the fixed IP

address.

If you do not know these information in detail, please contact your ISP to get

these informations.

What you need

in your side

Andere Handbücher für Vigor2500 series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Draytek Netzwerk-Router Handbücher

Draytek

Draytek Vigor2866 Series Bedienungsanleitung

Draytek

Draytek VigorSwitch P1080 Bedienungsanleitung

Draytek

Draytek Vigor 2132 Series Bedienungsanleitung

Draytek

Draytek Vigor2900V Bedienungsanleitung

Draytek

Draytek Vigor 3100 Series Bedienungsanleitung

Draytek

Draytek Vigor3300V+ Bedienungsanleitung

Draytek

Draytek Vigor2710 Series Bedienungsanleitung

Draytek

Draytek VIGOR VIGOR2750 Bedienungsanleitung

Draytek

Draytek Vigor 3300 Series Bedienungsanleitung

Draytek

Draytek Vigor2955 Bedienungsanleitung

Draytek

Draytek Vigor 3200 Series Bedienungsanleitung

Draytek

Draytek Vigor 2800 Bedienungsanleitung

Draytek

Draytek Vigor2130 Series Bedienungsanleitung

Draytek

Draytek Vigor2952 Series Bedienungsanleitung

Draytek

Draytek Vigor2100 Bedienungsanleitung

Draytek

Draytek Vigor2100VG Bedienungsanleitung

Draytek

Draytek VigorPro 5500 Referenzhandbuch

Draytek

Draytek VIGOR2950 Bedienungsanleitung

Draytek

Draytek Vigor2600 plus Series Bedienungsanleitung

Draytek

Draytek Vigor2927 Series Bedienungsanleitung

Draytek

Draytek Vigor2760 Bedienungsanleitung

Draytek

Draytek Vigor1000 Series Bedienungsanleitung

Draytek

Draytek Vigor2912 Series Bedienungsanleitung

Draytek

Draytek Vigor 2700 Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise