Drive Medical PowerStroll Benutzerhandbuch

OWNER’S HANDBOOK

™

PowerStroll Owner’s Handbook Page 2 of 8 Part Code: Z24002 (Iss 02/12)

Contents

1. Introduction

2. Safety Procedures

3. Parts Description

4. Installation Instructions

5. Disassembly and Transportation

6. Battery Charging and Care

7. Operating the PowerStroll

8. Troubleshooting

9. Specification

10. Warranty

11. Compatibility with Drive Wheelchairs

Introduction

The PowerStroll is designed as an aid to a

wheelchair attendant providing power to

aid pushing in otherwise strenuous

situations such as up steep hills, etc.

The PowerStroll is designed to work in

conjunction with most wheelchairs with seat

widths between 16” and 20” (40cm – 50cm).

The PowerStroll will also fit some narrow

width wheelchairs such as Drive Medical’s

Lightweight Aluminium.

The PowerStroll is to be controlled by an

attendant with a manual wheelchair and

user up to a combined weight of 18 stone

(115kg).

The PowerStroll uses a 12V 20ah battery,

and has a range of up to ten miles between

charges.

The PowerStroll is manufactured by Drive

Medical Ltd and is CE marked. Drive

Medical Ltd is an ISO 9001 and ISO 13485

certified Medical Device Manufacturer.

Safety Procedures

The PowerStroll must not be used solely by

the wheelchair user under any

circumstances.

Ensure the PowerStroll is installed as far to

the rear of the wheelchair as is comfortable

for the attendant to do so.

Operate the PowerStroll at a speed that is

both comfortable for the operator and

wheelchair user.

When connecting / disconnecting the

battery from the motor or the charger make

sure both the power to the charger and

PowerStroll handcontrol are switched off.

Ensure the PowerStroll is secured in transit.

It is also recommended that the battery is

disconnected.

Ensure that the battery is charged only with

the battery charger supplied with the

PowerStroll. Using another battery charger

may cause damage or injury.

Whilst the PowerStroll has been EMC

tested, it may be susceptible to certain

types of electromagnetic waves. Avoid

close proximity to mobile phones,

commercial broadcast towers and

emergency services’ radios. Other

household appliances are not known to

pose any such risk. If involuntary movement

occurs, switch off the PowerStroll and

report this to your dealer.

The PowerStroll should not be used when it

is snowing or during heavy rain. This may

cause damage to the PowerStroll. The

PowerStroll should not be exposed to damp

conditions or direct sunlight.

Note: Wheelchairs fitted with attendant

cable brakes. On such wheelchairs, the

attendant brake levers should be removed

prior to fitting. If the attendant brakes do

not have a separate parking brake facility,

then parking brakes should be added to the

wheelchair.

PowerStroll Owner’s Handbook Page 3 of 8 Part Code: Z24002 (Iss 02/12)

Parts Description

LIFT UP

STRAP

HAND

SET

BATTERY

PACK

POWER

PACK

Installation Instructions

1. Handset Installation

Loosen both knobs on the handset.

Squeeze the crocodile clip on the handset

and apply to the push handle as shown.

Secure the clip by turning the outer knob

clockwise.

Tilt the handset to the required angle then

tighten the inner knob clockwise to secure.

2. Bracket Installation

Install both brackets on the bottom

horizontal tubing of the wheelchair, using an

Allen Key (as shown in the photo above)

Ensure that the screws are sufficiently tight

and do not rotate on the tubing. Ensure that

the hole on each bracket is horizontal and

level with each other.

3. Powerpack Installation

Feed the telescopic bar through the front

end of the powerpack. Slacken the other

tristar knob on the bar and insert one end of

the bar in to the bracket (as shown above).

Slide the telescopic section out until the end

of the bar locates fully in the hole on the

other bracket. Position the powerpack

centrally between the wheelchair. Tighten

the tristar knob to secure the installation.

PowerStroll Owner’s Handbook Page 4 of 8 Part Code: Z24002 (Iss 02/12)

4. Battery Pack Installation

Place the battery in to the tray on top of the

powerpack, ensuring the pack handle is on

the left hand side of the powerpack (as

shown above)

Connect the red and black connector on the

battery pack to the red and black connector

on the powerpack (as shown above)

5. Final Connection

Connect the cable from the powerpack in to

the underneath of the handset (as shown

previously).

Place the top loop of the lift-up strap around

the opposite push handle to the handset.

Disassembly and Transportation

1. Switch the PowerStroll off at the ignition.

2. Disconnect / unclip the powerpack

connector from underneath the handset.

3. Remove the lift-up strap from the push

handle.

4. Disconnect the red and black connector on

battery pack from the red and black

connector on the powerpack. Lift out of the

battery tray using the handle.

5. Slacken the tristar knobs and slide the

telescopic bar inwards to remove the

powerpack from the wheelchair.

Notes:

The battery supplied with the PowerStroll is

classified as safe for air travel by compliance

with IATA special provision A67.

The battery pack has a fabric handle to make

it easy to carry.

Battery Charging and Care

Follow the procedure below step by step:

1. Turn the power switch to (OFF)

2. Disconnect the red and black connector on

battery pack from the red and black

connector on the powerpack. Lift out of the

battery tray using the handle.

3. Plug the charger’s power cord into the

mains.

4. Plug the charger’s red and black connector

into the red and black connector from the

battery pack

5. Switch on the plug socket.

6. The charger’s LED will illuminate orange to

indicate the batteries are charging. The

charging duration is about 8 hours. To

ensure optimum performance a 12-hour

charge is recommended.

PowerStroll Owner’s Handbook Page 5 of 8 Part Code: Z24002 (Iss 02/12)

1. The orange LED will turn green when

charging is complete.

2. Turn off the charger, disconnect the power

cord and the round plug from the battery

pack.



Suggestion

1. Do not disconnect the charger cord

if charging is not completed. The

battery life will be seriously

shortened or decayed if the

battery is repeatedly used without

being fully charged. Therefore be

sure to charge the battery fully

every time.

2. Always complete the charging until

the LED light turns green. NEVER

stop charging before it is complete.

3. When fully charged, the battery

charger will still trickle charge the

battery to ensure optimum range.

4. If you do not use your powerpack

for a long time, it should be

charged at least every week to

keep the battery in a fully usable

condition.

5. The ambient temperature will

affect charging time. Charging time

will be longer in the winter.

6. After charging, do not leave the

charger socket plugged in to the

scooter, as this will cause a power

drain on the powerpack and

temporarily reduce its range.

7. The batteries carry a twelve-month

manufacturer's warranty. This

warranty only covers issues relating

to manufacturing faults, and not

faults relating to failure to recharge

the batteries as instructed above.



Attention: Please follow the rules below

to avoid accidents while charging.

1. Only use the supplied charger, and

recharge the battery to its full

capacity every time. You may

damage the battery if you use a

charger which is not to the correct

specification.

2. Never disassemble or modify the

charger.

3. Please charge in a well-ventilated

space where there is no direct

exposure to the sunlight. Do not

charge in surroundings where it is

humid, raining or dewy.

4. Do not charge in temperatures less

than -10°C or higher than +50°C as

the charger may not work well &

batteries may become damaged.



Warning

1. Keep away from flammable objects

while charging as this may lead to

fire or battery explosion.

2. Do not smoke while charging as the

battery may release hydrogen gas.

Always charge your battery in a

well-ventilated space.

3. Never connect or disconnect the

plug or cord with wet hands whilst

charging. Do not connect or

disconnect the plug or cord when

they are wet, it may lead to electric

shock.

Charger

The charger supplied has an LED which changes

colour depending on its status:

If the LED is lit ORANGE then the charger is

switched on and charging

If the LED is lit GREEN then the charger is

switched on and has finished the bulk of its

charging and the batteries can be used. However,

we recommend that you leave the charger

charging for a couple of hours after the green

LED has lit. This will maintain and probably

increase the capacity of your batteries.

The LED will also illuminate GREEN if the charger

is switched on but not connected to the

batteries.

Batteries

Do not expose the battery pack to temperatures

below -10º or above 50ºC when charging or

storing.

The batteries are maintenance free and there is

no need to inspect the battery liquid or refill with

water.

You are required to charge the batteries on a

regular basis. Even if the powerpack is not used,

it should be charged at least once a week.

The battery pack contains one 12V 20ah batteries.

The battery supplied with the PowerStroll is

classified as safe for air travel by compliance with

IATA special provision A67.

PowerStroll Owner’s Handbook Page 6 of 8 Part Code: Z24002 (Iss 02/12)

Charging the Batteries

Using the charger supplied, the charging duration

is about 8 hours.

However, to ensure optimum performance we

recommend a 12-hour charge.

We also recommend that the batteries are

not charged for more than 24 hours.

Operating the PowerStroll

Reversing. The PowerStroll comes with a lift-

up strap to allow the wheelchair to reverse.

Lift up the PowerStroll with the strap and

hook the second loop around the push

handle. Please note that failure to lift up the

PowerStroll when reversing may cause the

pack to flip over.

Maximum Speed. Always set a maximum

speed which you are comfortable walking

with.

Pushing the Wheelchair When Not In Use.

We recommend that the powerpack is

restrained with the lift-up strap when not in

use.

Handset Operation

SPEED

DIAL

TRIGGER

POWER

EYE

OUTER

KNOB

INNER

KNOB

IGNITION

Ignition –Insert the key and turn clockwise to

switch the PowerStroll on. Turn the key

anticlockwise to switch the PowerStroll off.

The key can be removed when the unit is

switched off.

Please note there is a 2-second delay when

starting up the PowerStroll before the wheel

will move. Wait 2 seconds before sequeezing

the trigger.

Trigger –Squeeze the trigger to propel the

PowerStroll. The more the trigger is

squeezed, the faster the PowerStroll will

travel. Release the trigger to stop the

PowerStroll.

Speed Dial –Turn the dial clockwise to

increase the maximum speed of the

PowerStroll. Turn the dial anticlockwise to

reduce the PowerStroll’s maximum speed.

Power Eye –This is lit green when the

PowerStroll is switched on.

Outer Knob –This is used to secure the clip

holding the handset to the push handle

Inner Knob –This is used to determine the

angle of the handset.

Specification

Weight: 7.5kg (without battery)

6.5kg (battery pack)

14kg (total weight)

Max speed: 3mph / 5kph

Max gradient: 6º

Cruising range up to 10 miles (16km)

Weight capacity:

21 stone (115kg) including wheelchair & user

Motor: 12V 100W D.C.

Battery: 12V 20ah Sealed Lead Acid

Charger: 3A 12V output

PowerStroll Owner’s Handbook Page 7 of 8 Part Code: Z24002 (Iss 02/12)

TroubleShooting

Wheelchair does not move when trigger is pressed.

Possible Solutions:

Check the PowerStroll is switched on.

Check the battery is fully charged.

Check the connection between the battery and

motor is correct.

Check the wheelchair brakes are not applied.

Check the drive wheel is in contact with the

ground.

Wheelchair is difficult to push manually.

Possible Solutions:

Check the wheelchair brakes are not applied.

Remove PowerStroll.

The PowerStroll is too fast / slow.

Try varying the speed with speed dial.

Try recharging the batteries (if too slow).

Check the wheelchair brakes are not applied.

Warranty

To improve the safety and lifespan of your

PowerStroll, it is recommended that you have it

serviced on a regular basis. Recommended

Service Schedules for PowerStrolls are available

to service agents.

There is a comprehensive twelve-month

warranty from the date on which your new

PowerStroll is delivered. The warranty covers

the PowerStroll for replacement parts during

this period. For more detail, please see the

warranty conditions below:

1. Any work or replacement part

installation must be carried out by an

authorised Drive Medical dealer /

service agent.

2. To apply the warranty should your

PowerStroll require attention please

contact the outlet from which you

purchased the PowerStroll.

3. Should any part of the PowerStroll

require repair or full or part

replacement, as a result of a

manufacturing or material defect within

the warranty period, parts will be

supplied free of charge.

Note: The guarantee is not transferable.

4. Any repaired or replaced parts will be

covered by the balance of the warranty

period on the PowerStroll.

5. Parts replaced after the original warranty

has expired will be covered by a three-

month warranty.

6. Consumable items supplied will not

generally be covered during the normal

warranty period unless such items require

repair or replacement clearly as a direct

result of a manufacturing or material

defect. Such items include (among others):

upholstery and tyres.

7. The above warranty conditions apply to a

brand new PowerStrolls. Ex-demonstration

PowerStrolls supplied directly by Drive

Medical carry a six-month warranty period.

If you are unsure whether your PowerStroll

is covered contact your dealer.

8. Under normal circumstances, no

responsibility will be accepted where the

PowerStroll has required assistance as a

direct result of:

a. the PowerStroll part not having been

maintained in accordance with the

manufacturers recommendations

b. failure to use the manufacturer’s

specified parts

c. the PowerStroll or part having been

damaged due to neglect, accident or

improper use

d. the PowerStroll or part having been

altered from the manufacturer’s

specification or repairs having been

attempted before the dealer is notified

In the event of your PowerStroll requiring

attention, please contact your service agent /

dealer and give all relevant details so

they can act quickly.

The manufacturer reserves the right to alter

without notice any weights, measurements or

other technical data shown in this manual. All

figures, measurements and capacities shown

in this manual are approximate and do not

constitute specifications.

PowerStroll Owner’s Handbook Page 8 of 8 Part Code: Z24002 (Iss 02/12)

Compatibility with Drive Wheelchairs

The PowerStrolls are compatible with following

Drive wheelchairs:

Budget Steel Wheelchairs

(product codes: CS1142SP and CS1142TS)

Steel Chair Wheelchairs –self propel

(product codes: SSP16, SSP18, SSP18E and SUSP18)

Steel Chair Wheelchairs –transit

(product codes: STS16, STS18, STS18E and SUTS18)

Lightweight Aluminium Wheelchairs

(product codes: LAWC001 and LAWC002*)

Standard Aluminium Wheelchairs

(product codes: XSAWCSP18, XSAWCTS18*,

XSAWCSP20 and XSAWCTS20*)

Super Deluxe Wheelchairs

(product codes: XSSDSP16/18/20 & XSTS16/18/20*)

Spirit Wheelchairs (product code: XSES18)

* The wheelchairs marked with ‘*’ will require

the attendant brake levers and cable

removing from the wheelchair prior to use.

The actual brake unit can still be used as a

parking brake with these parts removed.

The above list is current at time of printing, and the

omission of a Drive wheelchair from this list does not

mean that the PowerStroll is incompatible with it.

For more information please contact your local Drive

Medical dealer.

Compatibility with Other Wheelchairs

The PowerStroll is suitable for most folding wheelchairs:

with a distance between tubing edges

(W)

14½5 ” to 20” (37cm – 50cm). This is usually,

but not always, the same as the wheelchair

seat width

a round tubing diameter

(D)

between 7/8” -

1” (22mm – 25mm)

Please note that you should check with your dealer

and/or the wheelchair manufacturer. Drive Medical

does not accept any responsibility for other

manufacturer’s wheelchairs, and in some

circumstances a risk assessment should be carried

out prior to installation.

Manufacturer Details

Drive Medical Ltd,

Ainley’s Industrial Estate,

Elland, GB HX5 9JP.

+44 (0) 1422 314488

enquiries@drivemedical.co.uk

www.drivemedical.co.uk

Inhaltsverzeichnis

Andere Drive Medical Mobilitätshilfe Handbücher

Drive Medical

Drive Medical RTL10266CF Bedienungsanleitung

Drive Medical

Drive Medical 10200-2 Bedienungsanleitung

Drive Medical

Drive Medical CE 1315 Bedienungsanleitung

Drive Medical

Drive Medical 796 Bedienungsanleitung

Drive Medical

Drive Medical PC 1000 R Bedienungsanleitung

Drive Medical

Drive Medical Drive 12402 Bedienungsanleitung

Drive Medical

Drive Medical 13030-1SV Bedienungsanleitung

Drive Medical

Drive Medical Roomba Bedienungsanleitung

Drive Medical

Drive Medical Migo Benutzerhandbuch

Drive Medical

Drive Medical RTL10266CF Bedienungsanleitung

Drive Medical

Drive Medical Nitro RTL10266TWHL Bedienungsanleitung

Drive Medical

Drive Medical Trekker TK 1000 Bedienungsanleitung

Drive Medical

Drive Medical Duet Bedienungsanleitung

Drive Medical

Drive Medical RTL12000 Bedienungsanleitung

Drive Medical

Drive Medical 10221 FRD-1 Bedienungsanleitung

Drive Medical

Drive Medical walking stick Bedienungsanleitung

Drive Medical

Drive Medical WA008 Bedienungsanleitung

Drive Medical

Drive Medical 548 Bedienungsanleitung

Drive Medical

Drive Medical 10263 KDR Bedienungsanleitung

Drive Medical

Drive Medical 10219C-2 Bedienungsanleitung

Drive Medical

Drive Medical 11117N-1 Bedienungsanleitung

Drive Medical

Drive Medical FC 2024 Bedienungsanleitung

Drive Medical

Drive Medical R6 Benutzerhandbuch

Drive Medical

Drive Medical i-walker Bedienungsanleitung

Beliebte Mobilitätshilfe Handbücher anderer Marken

Alber

Alber Scalamobil iQ Bedienungsanleitung

Ferno

Ferno CCT-PX Bedienungsanleitung

HEPRO

HEPRO Gripo Bedienungsanleitung

Otto Bock

Otto Bock Pheon 3R62 Bedienungsanleitung

NRS Healthcare

NRS Healthcare M11090 Bedienungsanleitung

Medline

Medline MDS86835DSHEC Installationsanleitung

Guldmann

Guldmann Twin Turner II Bedienungsanleitung

Drive

Drive ROOMBA Bedienungsanleitung

Gate

Gate Balder Bedienungsanleitung

Decon wheel

Decon wheel TNS Notos Bedienungsanleitung

ExoAtlet

ExoAtlet ExoAtlet-II Bedienungsanleitung

Invacare

Invacare Storm Series Bedienungsanleitung

Rhythm Healthcare

Rhythm Healthcare B3800F Bedienungsanleitung

AMF-BRUNS

AMF-BRUNS PROTEKTOR Bedienungsanleitung

Drive DeVilbiss Healthcare

Drive DeVilbiss Healthcare OTTER Bedienungsanleitung

Rhythm Healthcare

Rhythm Healthcare C500U Bedienungsanleitung

Lumex

Lumex RJ4200A Bedienungsanleitung

Rebotec

Rebotec Jumbo Bedienungsanleitung