Drone DR-2000 Bedienungsanleitung
TM
DR-2000 Install Guide
Firstech, LLC.
21903 68th Avenue South
Kent, WA 98032
Phone/Téléphone: 888-820-3690
Fax/Télécopieur: 206-957-3330
Please visit www.dronemobile.com for additional information
Veuillez visiter www.dronemobile.com pour plus d’information.
Guide d’installation DR-2000
Table of Contents
1 | Copyright 2012 Firstech, LLC.
Introduction
Introduction and Notices 2
Type 1 - Standalone With RF Kit and Bypass
Type 2 - Data
Type 3 - Slave / Hardwire
4
5
6
Wiring Details
Dealer Activation
Suggested Mounting Locations
7
9
10
LED Diagnostics
Frequently Asked Questions 24
24
Wiring Diagrams
Details
Troubleshooting
TM DR-2000 Install Guide
Installation Overview
Programming
Remote Programming Routine
Valet Mode
Engine Sensing
Using FT-EZGO With DR-2000
Option Tables
Option Descriptions
Option Programming Instructions
3
11
11
12
13
14
17
20
TM DR-2000 Install Guide
Copyright 2012 Firstech, LLC. | 2
Introduction
Welcome to the DroneMobile DR-2000 installation manual. This manual is intended for experienced
installers only. We highly recommend that you contact your local DroneMobile dealer and seek
professional installation. Call 888-820-3690 for more information.
Please observe the following guidelines when installing this system:
Programmable Output Connectors and timing settings can only be changed by the FT-•
OP500-KIT. Other options can be programmed by a Firstech compatible RF Kit.
Do not use the battery backup port on the CM5 or CM6 Series control modules to power the•
DR-2000. It does not provide enough current. Use a power supply that can support up to 2
amps of current draw. Please use a digital multimeter to test all wires.
Drone 2 comes with the Type 2-Data Harness. The Hardwire Harness and External Antennas are•
available for an additional cost.
A Firstech remote start system MUST be installed to utilize all DroneMobile features. DroneMobile•
may be used with an aftermarket remote start but the Hardwire harness is required.
When using Type 1 installation and an RF Kit, you must program those remotes to the Drone.•
Please refer to the remote user manual for instructions.
Do not install under metal panels as that will hinder GPS and/or cellular signal.•
Once installation is complete do not connect the plugs into the DR-2000. First activate and
register your DroneMobile online at https://live.dronemobile.com/login. Click on “New Dealer
Registration” or login with your Dealer Account. Activate and wait for the SIM status to change to
“Active.” DroneMobile carries a 1 year manufacturer’s warranty.
Firstech, LLC. does not condone
or recommend installing DR-2000
on a vehicle with a fuel or ignition
interrupt. Doing so may result in
damage to the vehicle and/or injury
to driver.
Firstech, LLC. will not assume any
responsibility for improper use
and/or installation. For Terms
and Conditions refer to www.
dronemobile.com/usersmanuals
Introduction and Notices
These installation steps are very important. Please follow them carefully when
installing your first and every DroneMobile system. The Drone’s SIM MUST be
activated prior to powering on the DR-2000.
STEP 1: Install DroneMobile (and alarm/remote start system if applicable). Leave harnesses unplugged
from DR-2000.
STEP 2: Go to https://live.dronemobile.com/login and click on “New Dealer Registration.” If you
already have an account, login with your Dealer account information.
STEP 3: Register the Drone unit using the 20 digit serial number. (Click on “New Dealer Registration”
if this is your first time registering a Drone unit.) “Activating the SIM” window will open.
STEP 4: Once the “Activating the SIM” window closes and the status changes to “Active” you may
now plug the harnesses into the DR-2000.
STEP 5: Wait for the unit to achieve cell lock (blue LED flashes slowly)
STEP 6: Once the unit has achieved cell lock, power cycle (unplug) the unit once more. Wait for the
unit to achieve cell lock then you may proceed to the “Settings” page.
STEP 7: Complete the “Hardware Installation,” “Controller Settings,” and “Alert Notifications” sections.
Click “Save”to save your settings.
STEP 8: Once you are on the “Controls”page, test all of the features including GPS tracking to verify
that the unit is fully functional before releasing the vehicle.
STEP 9: Give your customer the 20 digit serial number and Quick Start Card and have them register
the unit in their name by going to https://live.dronemobile.com/login and clicking on “New
User Registration.” If they currently have an account, have them log in and “Manage Account”
> “Add/Remove Vehicle(s).”
Installation Overview
3 | Copyright 2012 Firstech, LLC.
Failure to select correct install type will require a call to tech support to reset.
If you log out of this session or your session expires, you have until midnight
the day of activation to log back in. Once the end user registers their Drone,
you will no longer have access to the unit.
TM DR-2000 Install Guide
Wiring Diagrams
DroneMobile can be installed using installation Type 1-Standalone, Type 2-Data, and Type 3-Hardwire
Required
Optional
Follow Type 1 when using DroneMobile as a standalone system
and GPS tracking device. Firstech RF kit is optional.
Copyright 2012 Firstech, LLC. | 4
Type 1 - Standalone With RF Kit and Bypass
Red: (+) 12 Volt Constant
Yellow:
White:
Blue/Black: (-) Programmable Output 1
Brown: (-) Programmable Alarm Trigger Input
Green: (+) Ignition Input
Black: (-) Ground Input
Blue(Thin)
Blue: (-) Programmable Output 2
Orange: (-) Programmable Output 3
Optional External Cellular Antenna Port
Optional External GPS Antenna Port
Yellow:
White:
Black:
Black:
Orange:
GPS
GSM
TM
Reset Button
6 Pin Antenna Port
RS232 Data Port
4 Pin Antenna Port
12V+ Constant
12V+ Ignition
Chassis Ground
See Option 2-05
See Special Option Group 2
Bypass Module
TM
Do Not Use Both Antenna
Ports At The Same Time
See Special Option Group 2
See Special Option Group 2
DR-2000 Install Guide
TM
Wiring Diagrams
Required
Optional
DR-2000 Compatible
Firstech Control Module
Follow Type 2 when using DroneMobile with a
compatible Firstech Control Module
5 | Copyright 2012 Firstech, LLC.
The Green Ignition Wire is only used if the
contol module does not support 2 Way Data or
Ignition signal through data.
Type 2 - Data
Red: (+) 12 Volt Constant
Black:
N/A
N/A
N/A
Green: (+) Ignition Input
Black: (-) Ground Input
N/A
N/A
N/A
12V+ Ignition
Yellow:
White:
Black:
To RS232 Data Port On
Control Module
Optional External Cellular Antenna Port
Optional External GPS Antenna Port
GPS
GSM
TM
Reset Button
DR-2000 Install Guide
TM
Wiring Diagrams
Required
Optional
Compustar or
Aftermarket
Remote Start *
Follow Type 3 when connecting DroneMobile to a non-data
Firstech control module or aftermarket alarm and remote start
Copyright 2012 Firstech, LLC. | 6
Type 3 - Slave / Hardwire
6 Pin Antenna Port (Not Used)
RS232 Data Port (Not Used)
4 Pin Antenna Port (Not Used)
Red: (+) 12 Volt Constant
Yellow:
White:
Blue/Black: (-) Programmable Output 1
Brown: (-) Programmable Alarm Trigger Input
Green: (+) Ignition Input
Black: (-) Ground Input
Blue(Thin)
Blue: (-) Programmable Output 2
Orange: (-) Programmable Output 3
Optional External Cellular Antenna Port
Optional External GPS Antenna Port
Yellow:
White:
Black:
Black:
Orange:
GPS
GSM
TM
Reset Button
12V+ Constant
12V+ Ignition
Chassis Ground
*See Option 2-05
*See Special Option Group 2
*See Special Option Group 2
*See Special Option Group 2
DR-2000 Install Guide
TM
Details
Wiring Details
Data Harness (DR-HRN-2KDA Included In Box)
Green: (+) Ignition Input - Connect this wire to the vehicle’s ignition output. This wire should see
(+) 12V when the vehicle’s key is in the “on” position. This wire is not required in Type 2 installations
unless the Drone compatible Data Controller requires it.
RS232 Plug - This plug is intended to connect to the RS232 Data Port on CM5 or newer Firstech
compatible control modules. (Not compatible with LT Series) The control module must have the most
current firmware to be Type 2 compatible.
Type 1/3 Hardwire Harness (DR-HRN-2KHW)
Red: (+) 12 Volt Constant Input - This is the constant power for the DR-2000. It carries a 2 amp fuse
and must be connected to the vehicle’s constant (+) 12 Volt source.
Green: (+) Ignition Input - Connect this wire to the vehicle’s ignition output. This wire should see (+)
12V when the vehicle’s key is in the “on” position. This wire is required in Type 1 in order to program
the remotes.
Black: (-) Ground Input - Connect this wire to the vehicle’s chassis ground.
Blue/Black: (-) Programmable Output 1 - This wire provides a programmable negative (-) output
that can be programmed on the Drone’s Option Menu. Please see the Special Option Group 2 Menu
for details. At the default setting this wire acts as a door lock output. This wire is not available in Type
2 installations. You must wire a relay to provide a positive (+) output.
Blue: (-) Programmable Output 2 - This wire provides a programmable negative (-) output that can
be programmed on the Drone’s Option Menu. Please see the Special Option Group 2 Menu for
details. At default setting this wire acts as a door unlock output.
7 | Copyright 2012 Firstech, LLC.
DR-2000 Install Guide
TM
Wiring Details
Details
This wire is not available in Type 2 installations. You must wire a relay to provide a positive (+) output.
Orange: (-) Programmable Output 3 - This wire acts as a programmable negative (-) output for the
Drone. Please see the Special Option Group 2 Menu for details. At the default setting this wire will
send a negative start trigger output. Setting 2 changes this output to a negative parking light output.
Brown: (-) Programmable Auxiliary Trigger Input - See option 2-05. This wire acts as a
programmable negative input for the Drone. At default it will take a negative 5 pulse trigger. It can
be programmed to take a negative latched input. Upon trigger this wire will send an alarm triggered
notification to the web interface and user’s smartphone. Setting 3 changes this wire to a negative (-)
foot brake input. It will shut the remote starter down. This wire is not required in Type 2 installations.
4 Pin Antenna Port - This plug is intended to connect to a Firstech compatible antenna from a
compatible RF Kit. This is used if using Drone as a standalone piece as shown in Type 1 installations.
You can also use this port to connect the OP500 Option Programmer and set options. Do not use
both 4 Pin and 6 Pin Antenna Ports at the same time.
6 Pin Antenna Port - This plug is intended to connect to a Firstech compatible antenna from a
compatible RF Kit. This is used if using Drone as a standalone piece as shown in Type 1 installations.
You can also use this port to connect the OP500 Option Programmer and set options. Do not use
both 4 Pin and 6 Pin Antenna Ports at the same time.
RS232 Port - This port is used when connecting to a Drone compatible bypass module. The DR-2000
supports both ADS and Fortin bypass modules. (See Option 2-06) This port is typically used in Type 1
installations.
Copyright 2012 Firstech, LLC. | 8
DR-2000 Install Guide
TM
Activation and Placement
9 | Copyright 2012 Firstech, LLC.
Dealer Activation
STEP 1: The Drone’s SIM MUST be activated prior to powering on the DR-2000. Complete all
connections. Leave harness unplugged from DR-2000.
STEP 2: If you are a new DroneMobile dealer please visit https://live.dronemobile.com/login to
register your account. Click on “New Dealer Registration” and fill out the required information. Your
account will be used for any and all future DroneMobile activations so please do not lose the
login and password.
STEP 3: Complete this step before plugging the main harness into the DR-2000: Once logged in
you should be able to enter the 20 digit serial number and click “Submit.” “Activating the SIM” window
will open.
STEP 4: Once the “Activating the SIM” window closes and the status changes to “Active” you may
now plug the harnesses into the DR-2000.
STEP 5: Once the unit has achieved cell lock (blue LED flashes slowly), power cycle (unplug) the unit
once more. Wait for the unit to achieve cell lock then you may proceed to the “Settings” page. Please
see the Troubleshooting section for description of LEDs. Please complete all necessary tests of the DR-
2000.
Note: If you log out of this session or your session expires, you have until midnight the day
of activation to log back in. Once the end user registers their Drone, you will no longer have
access to the unit.
STEP 6: Complete the “Hardware Installation,” “Controller Settings,” and “Alert Notifications” sections.
Configure the other settings and click “Save”to save your settings. Installation type selection is not
required when using hardwire harness. (DR-HRN-2KHW)
DR-2000 Install Guide
Inhaltsverzeichnis
Sprachen:
Beliebte Autoalarmanlage Handbücher anderer Marken
Federal Signal Corporation
Federal Signal Corporation Pathfinder Siren Series Handbuch
Falcon
Falcon Predator XL3 Benutzerhandbuch
Audiovox
Audiovox Auto Security XR91 Betriebsanleitung
Clifford
Clifford Sabre II Bedienungsanleitung
CrimeStopper
CrimeStopper CS-8717 Kurzanleitung
Ultra Start
Ultra Start 450 SERIES Bedienungsanleitung
