DTS XR 5 WASH Bedienungsanleitung

XR 5 WASH XR 5 WASH

User Manual Rel 1.1

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della D.T.S.

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di

design a ciascun proprio prodotto. D.T.S. non assume alcuna responsabilità sull’uso o sull’applicazione

dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products

without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits

described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou

de design, sans préavis, à chacun de ses produits. D.T.S. décline toute responsabilité sur l'utilisation ou

sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

o reproducido, total o parcialmente, sin previa autorizaciónescrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter

estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume responsabilidad de

ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

ARC 1200

XR 5 WASH

INDEX:

1- TECHNICAL FEATURES 4

2- IMPORTANT SAFETY INFORMATION 5

2.1 Fire prevention

2.2 Prevention of electric shock

2.3 Protection against ultraviolet radiation

2.4 Safety

2.5 Level of protection against the penetration of solid and liquid matter

3- MOUNTING THE LAMP 6

3.1 Lamp alignment

4- VOLTAGE AND FREQUENCY 7

5- INSTALLATION 7

5.1 Safety cable

5.2 Protection against liquids

5.3 Movement

5.4 Risk of fire

5.5 Forced ventilation

5.6 Ambient temperature

6- MAINS CONNECTION 8

6.1 Protection

7- DMX SIGNAL CONNECTION 9

7.1 DMX Addresses

7.2 Selecting the DMX address

8- DISPLAY FUNCTIONS 11

9- PAN & TILT SPEED 14

10- FANS SPEED

11- ERROR MESSAGES

12- HIDDEN MENU 15

13- OPENING THE PROJECTOR HOUSING 16

14- PERIODIC CLEANING

14.1 Lenses and reflectors

14.2 Fans and air passages

15- PERIODIC CONTROLS

16- DMX PROTOCOLS 17

17-COLOUR WHEEL 22

ARC 1200

XR 5 WASH

1- TECHNICAL FEATURES

The XR 5 Wash is fitted with a Philips MSD 250/2 discharge lamp

(GY9,5 lampholder base), with a colour temperature of 8500 °K and a luminous flux of

18,000 Lumens.

Average lifespam is 2000 hours, with replacement recommended before 2200 hours

Other recommended lamps: Osram HSD 250/2, GE CSD 250/2.

The unit incorporates:

Power supply

Electromagnetic ballast: 230 V (50/60 Hz) standard. On request 110 V 50/60 Hz.

Power consumption 350 W

Remote Lamp on/off via DMX

Operating ambient temperature -10° / 40°

Weight

20 Kg

Motorized zoom (13°-23°), rotating and indexable beam shaper (0°-170°), frost filter, 2

colour conversion filters (3.200°K and 5.600°K), CMY colour generation + a colour wheel (6

dichroic filters + open, with linear selection, and electronic or electromagnetic ballast.

Optical group

Fresnel lens Ø 150 mm (Borosilicate dichroic parabolic reflector)

Zoom

Motorized zoom (13°-23°)

Dimmer / shutter / strobo

Linear dimmer - Shutter - Strobe from 0,85 flash/sec to 10 flash/sec

Colours

CMY color generation system with 3 palettes for gradual and linear insertion +

colour wheel (6 colours + open). Color change with blackout sync

Effects

Rotating and indexable beam shaper (0°-170°)

Colour conversion filters

3.200°K and 5.600°K

Pan / Tilt

Pan 540° (3,9 sec.) Tilt 270° (2,6 sec.) 16-bit resolution

16 DMX channels

Connections

4 XLR connectors (In and Out) with 3 and 5 pins.

Packing Dimensions

(HxWxL)

550 x 440 x 880 mm

Weight

27 Kg

540 mm

027 °

45mm

1 408 mm

33m6 m

5 0 mm

423 mm

ARC 1200

XR 5 WASH

2- IMPORTANT SAFETY INFORMATION

2.1 Fire prevention:

The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1 MT.

-Minimum distance from the closest illuminable surface: 2 MT.

-Replace any blown or damaged fuses only with fuses of identical value. Refer to the wiring diagram if

there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

2.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves

touching the inside of the moving head, including lamp replacement.

-The level of technology present in the Xr5 requires the assistance of specialised personnel for all

servicing. Please refer to an authorised DTS service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

2.3 Protection against ultraviolet radiation:

-Never turn on the lamp if any of the lenses, filters or ABS covering is damaged. Their respective

shielding functions will only operate efficiently if they are in perfect working order.

-Never look directly the lamp when it is on.

2.4 Safety:

-The projector should always be installed with bolts, clamps and other tools that are capable of

supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main

fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at

least 10 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should

not exceed 40°C.

-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.

-Always wear suitable hand protection when handling the lamp.

2.5 Level of protection against the penetration of solid and liquid matter:

-The projector is classified as an ordinary appliance and its protection level against the penetration of

solid and liquid matter is IP 20.

XR5 can fit a Philips MSD250/2 or a Osram HSD250/2 or a GE CSD250/2.

ARC 1200

XR 5 WASH

3- MOUNTING THE LAMPS

Warning: Switch off the unit before replacing the lamp.

1) Using a screwdriver, remove the 3 screws X,Y, Z, (photo 1) which fix the lamp holder.

2) Remove the lamp holder assembly and insert the lamp (photo 2).

The lamp used on XR 5 is made in quartz glass and should be handled with care. Always follow the

instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided

in the lamp's packaging. The GY9,5 lamp socket is not symmetrical.

DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat

the procedure.

3) Replace the lamp assembly and tighten the screws X,Y,Z, which were previously removed (photo3).

3.1 Lamp alignment

Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic

filters and other components inside the unit.

Alignment is carried out using the 3 adjusters A, B and C.

During this operation you must have a uniform luminosity all around the projected area.

Philips MSD250/2

Power 250W

Luminous flux 18.000 lm

Colour temperature 8.500°K

Lampbase GY9,5

Rated life 3,000 hours

Photo 2Photo 1 Photo 3

Photo 5

ARC 1200

XR 5 WASH

4- VOLTAGE AND FREQUENCY

The XR5 with electromagnetic ballast can operate at 230 VOLT 50-60 Hz (110 VOLT 50-60 Hz on

request)

5- INSTALLATION

XR5 may be either floor or ceiling mounted.

For floor mounting installations, the XR5 is supplied with four rubber mounting feet on the base.

For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the

mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the weight of the

unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to

move or shake whilst the XR5 is moving.

Four quarter turn fast locks placed on the base of the units,allows by using the two fast lock C clamps

provided in the box, to fix the unit in any position.

5.1- Safety cable

We recommend the use of a safety cable or chain connected to the Xr5 and to the suspension truss in

order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron

cable or chain can bear the weight of the entire unit.

You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown in the

picture below.

5.2- Protection against liquids

The projector contains electric and electronic components which should under no circumstances come

into contact with oil, water or any other liquid. The proper unit functioning would be compromised

should this occur.

ARC 1200

XR 5 WASH

5.3- Movement

The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any

obstructions in the path of the projector's movement.

5.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended

distance from flammable material is 1 MT.

Minimum distance from the object being illuminated is 2 MT.

5.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans located on both the

base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the

projector is in operation.

Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.

5.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow. The ambient temperature

should NOT exceed 40°C.

6- MAINS CONNECTION

XR5 with electromagnetic ballast operate at 230 VOLT 50-60 Hz.

Prior to connecting the unit to your mains supply,

ensure that the model in your possession correctly matches

the mains supply available. For connection purposes,

ensure that your plug is capable of supporting 3,15 amps at 230V,

Strict adherence to regulatory norms is strongly recommended.

6.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each XR 5.

A good earth connection is essential for the correct operation of the projector.

7- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the

projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a

CANNON XLR 5 or 3 pins connector.

540°

270°

Electromagnetic ballast

230V 50 / 60Hz

ARC 1200

XR 5 WASH

Ensure that the conductors do not touch each other.Do not connect the cable ground to the XLR chassy

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it

to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the

second one.

In this way, all the projectors are cascade connected.

NB. If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

For Installations where long distance DMX cable connections are needed,we suggest to use a DMX

terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

Between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

4 2

11=GND

2=DATA-

3=DATA+

CONTROLLER

S T A N D A R D

DM X 5 1 2

OUT

120 ohm

PIN 3

PIN 2

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

9ARC 1200

XR 5 WASH

7.1-DMX Addresses

XR 5 Wash have 16 DMX channels.

Set the following addresses on the mixer:

Projector 1 A001

Projector 2 A017 If you want to select the next projector, just add “16”

Projector 3 A033

….. A….

projector 6 A081

7.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will

start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the

projector is now setted to the new DMX address.

TRICKS:

if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a

faster selection.

10 ARC 1200

XR 5 WASH

Andere DTS Beleuchtungsausrüstung Handbücher

DTS

DTS Alchemy 7 Bedienungsanleitung

DTS

DTS NicKWash 600 Bedienungsanleitung

DTS

DTS Nick Wash 600 Bedienungsanleitung

DTS

DTS NICK NRG1200 CT Bedienungsanleitung

DTS

DTS NICK NRG 1201 Bedienungsanleitung

DTS

DTS 03.P16.02.01.LED PAR16 LED MR16 BLACK Bedienungsanleitung

DTS

DTS DELTA R FULL COLOR Bedienungsanleitung

DTS

DTS MOON 575 Bedienungsanleitung

DTS

DTS PROFILO 500 Bedienungsanleitung

DTS

DTS DELTA 12 HEAD Bedienungsanleitung

DTS

DTS ALCHEMY 5 Bedienungsanleitung

DTS

DTS HORUS FULL COLOUR Bedienungsanleitung

DTS

DTS PROFILO LED 80 Bedienungsanleitung

DTS

DTS DELTA 8 Series Bedienungsanleitung

DTS

DTS NICK NRG 1201 Bedienungsanleitung

DTS

DTS Scena LED 150 Bedienungsanleitung

DTS

DTS DIVE/R 18 RGB Bedienungsanleitung

DTS

DTS XM 1200 SPOT Bedienungsanleitung

DTS

DTS SCENA LED 80 WHITE Bedienungsanleitung

DTS

DTS XR5 SPOT Bedienungsanleitung

DTS

DTS SCENA COMPACT LED 50 Bedienungsanleitung

DTS

DTS XR1200 WASH Fresnel Bedienungsanleitung

DTS

DTS DELTA R FULL COLOR Bedienungsanleitung

DTS

DTS ALCHEMY 5 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung

LCG

LCG Thunder 400 Bedienungsanleitung