Dual Electronics Corporation XVM296BT Betriebsanleitung
INSTALLATION/OWNER’S MANUAL
Multimedia Receiver with Bluetooth®
featuring a 6.2" Touch Screen Display
XVM296BT
Copyright Notes
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc.
SD Logo is a trademark of SD-3C, LLC.
Other trademarks and trade names are those of their respective owners.
2
XVM296BT PREPARATION
Safety Information
Please read all instructions carefully before attempting to install or operate.
Due to its technical nature, it is highly recommended that your DUAL XVM296BT is installed by a professional
installer or an authorized dealer. This product is only for use in vehicles with 12VDC negative ground only.
To prevent damage or injury:
• Make sure to ground the unit securely to the vehicle chassis ground.
• Do not remove the top or bottom covers of the unit.
• Do not install the unit in a spot exposed to direct sunlight or excessive heat or the possibility of water splashing.
• Do not subject the unit to excessive shock.
• When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may
cause the unit to malfunction.
• To prevent short circuits when replacing a fuse, disconnect the wiring harness first.
• Use only the provided hardware and wire harness.
• You cannot view video while the vehicle is moving. Find a safe place to park and engage the parking brake.
• If you experience problems during installation, consult your nearest DUAL dealer.
• If the unit malfunctions, reset the unit as described on page 10 first. If the problem still persists, consult your
nearest DUAL dealer or call tech assistance @ 1-866-382-5476.
• To clean the monitor, wipe only with a dry silicone cloth or soft cloth. Do not use a stiff cloth, or volatile solvents
such as paint thinner and alcohol. They can scratch the surface of the panel and/or remove the printing.
• When the temperature of the unit falls (as in winter), the liquid crystal inside the screen will become darker than
usual. Normal brightness will return after using the monitor for a while.
• When extending the ignition, battery or ground cables, make sure to use automotive-grade cables or other cables
with an area of 0.75mm (AWG 18) or more to prevent voltage drops.
• Do not touch the liquid crystal fluid if the LCD is damaged or broken. The liquid crystal fluid may be hazardous
to your health or fatal. If the liquid crystal fluid from the LCD contacts your body or clothing, wash it off with soap
immediately.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
3
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it
would be subject to dust, dirt or excessive vibration.
Getting Started
• Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve.
• Install mounting sleeve into opening, bending tabs to secure.
• Connect wiring harness as shown on page 6. Consult a qualified technician if you are unsure.
• Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately).
• Reconnect negative battery terminal, and test for correct operation.
• Snap trim ring into place (if required).
• Slide unit into mounting sleeve to secure.
XVM296BT INSTALLATION
Preparation
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
Trim Ring
Main Unit
Taptite Truss
Head 5x6mm
Taptite Binding
Head 5x6mm
4
Wiring Diagram - Inputs/Outputs
XVM296BT INSTALLATION
Note:
When replacing a fuse, make sure to use the correct type and amperage. Using an incorrect fuse could cause
damage. The unit uses (1) 10 amp ATC mini style fuse located on the power connector.
Wiring Notes:
Subwoofer output
The Subwoofer preamp audio output (black jacket with green RCA) is active in all audio modes.
Rear camera input
A rear view camera (not included) can be used with the Camera input.
PARKING BRAKE
REVERSE
REMOTE TURN-ON
GRAY
GRAY/BLACK
5
Control Locations
XVM296BT OPERATION
Mode
Tune/Track Up
Power/Volume/Mute
Tune/Track Down
USB/microSD/AUX Inputs
1
2
3
4
5
2
1
4
3
6
XVM296BT OPERATION
Power On/Off
Volume
Mute
Mode
Auxiliary Input
USB Input
SD Card
Main Menu
Reset
Momentarily press to turn the unit on. Press and hold to turn the
unit off.
Rotate the volume knob to increase or decrease the volume level.
Momentarily press MUTE to silence the audio. Momentarily press MUTE
again to return to the previously selected volume. Rotating the volume
knob while the volume is muted will also cancel the mute function.
Press MODE to step through all available input modes: Radio, SD Card,
USB, Bluetooth Phone, Bluetooth Music, Auxiliary Input, Rear Camera
and Settings. Modes of operation are indicated on the display and/
or the monitor. Optional USB device and SD card must be connected/
inserted to appear in the mode selection string.
Connect external audio/video devices to the 3.5mm auxiliary input on
the front panel.
Insert a USB device to play MP3 files or view view AVI video files or
JPG photos.
Insert an SD card into the SD slot to play MP3 files or view view AVI
video files or JPG photos.
Press the house icon in the top left corner to access the Main Menu
screen.
To resolve abnormal operation or if the unit is inoperable, use the
tip of a pen to press the RESET button. The unit will reset the main
processor to the default settings.
General Operation
7
XVM296BT OPERATION
General Operation
From the Main Menu screen, select Settings to access the Setup menu and
select from three categories represented by the icons on the left side of the
screen: Settings, Audio and Bluetooth.
Settings:
• Time Setting - Access and adjust date and time settings.
• Beep - Turn the audible beep on or off.
• Camera - Turn the rear camera input on or off.
• Loudness - Press to turn Loudness feature on or off.
• Radio Area - Adjust the following radio options: USA, Asia, Europe or
South America.
• Calibration - Follow the prompts to calibrate the touch screen.
• Version - View current version numbers for the unit.
• Restore default - Press to restore unit to factory settings.
Audio:
• Sound Effect - Adjust EQ, Treble/Bass or Balance/Fader settings.
Bluetooth:
• Auto Connect - Turn Auto Connect feature on or off.
• Auto Answer - Turn Auto Answer feature on or off.
The touch screen controls on the bottom of each screen allow direct access
to important features during any mode of operation.
Press to dim the display.
Press to adjust audio options such as EQ, Treble/Bass or Balance/Fader.
Press to access the settings menu.
Setup Menu
Touch Screen
Controls
Dimmer 1
Audio 2
Settings 3
123
8
XVM296BT OPERATION
Select the Radio icon from the Main Menu screen.
Press to return to Main Menu screen.
Displays current mode of operation.
Press and hold << to seek a lower frequency. Press << momentarily
to tune the unit down one step at a time.
Press between 2 AM and 3 FM bands.
Press to toggle between Local and Distance tuning.
Press and hold >> to seek a higher frequency. Press >> momentarily
to tune the unit up one step at a time.
Press to toggle between Stereo and Mono tuning.
Press and hold to set the current station in that preset spot. Press
momentarily to recall the desired preset and begin playback.
Press to scan presets and listen to the first 10 seconds of each. Press
again to stop scanning and listen to the station. Press and hold to
automatically find and store the strongest stations as presets.
Radio Operation
Main Menu 1
Current Mode Indicator 2
Tune Frequency Down 3
Band 4
Local / Distance 5
Tune Frequency Up 6
Stereo 7
Preset Stations 8
AS/PS 9
1
3
2
AM/FM Tuner Operation
6
4
5
7
8
9
9
XVM296BT OPERATION
USB/SD Card Operation
USB/SD Operation
Main Menu 1
Current Mode Indicator 2
Repeat 3
Random 4
Previous File / Track 5
Play / Pause 6
Next File / Track 7
Folder Down 8
Folder Up 9
Direct Search 10
To play audio files from a USB device or SD card, insert device and
playback will begin automatically. To return to USB or SD card playback
from another mode of operation, select the corresponding icon from the
Main Menu.
• USB Playback - Insert a USB device into the USB slot on the side of
the unit.
• SD Card Playback - Insert SD card into the SD slot on the top of the
unit. When inserting an SD card, the label should face up.
Press to return to Main Menu screen.
Displays current mode of operation.
Press to select a repeat option: Repeat 1, Repeat Folder or Repeat Off.
Press to enable or disable random playback.
Press to go back to the previous file or track.
Press to pause or resume playback.
Press to advance to the next file or track.
Press to advance to the next folder.
Press to go back to the previous folder.
Press to directly enter file number to begin playback of that file.
12
3
4
5 6 7 8 9 10
Inhaltsverzeichnis
Andere Dual Electronics Corporation Empfänger Handbücher
Dual Electronics Corporation
Dual Electronics Corporation XVM286BT Betriebsanleitung
Dual Electronics Corporation
Dual Electronics Corporation XVM279BT Betriebsanleitung
Dual Electronics Corporation
Dual Electronics Corporation DM620N Betriebsanleitung
Dual Electronics Corporation
Dual Electronics Corporation DV737MB Bedienungsanleitung
Dual Electronics Corporation
Dual Electronics Corporation DM720 Betriebsanleitung
Dual Electronics Corporation
Dual Electronics Corporation XDVD176BT Betriebsanleitung
Dual Electronics Corporation
Dual Electronics Corporation DV715B Betriebsanleitung
Dual Electronics Corporation
Dual Electronics Corporation XVMBT279 Betriebsanleitung
