Dual XPA2100 Bedienungsanleitung

INSTALLATION/OWNER’S MANUAL

Mobile Power Amplifiers

XPA SERIES

XPA2100

XPA4100

XPA6100

XPA SERIES INSTALLATION

Preparation

Please read entire manual before installation. Due to the technical nature of amplifiers,

it is highly recommended that your DUAL amplifier is installed by a professional installer

or an authorized dealer.

Before You Start

• Disconnect negative battery terminal. (consult a qualified technician for instructions)

• Avoid installing the amplifier where it would be subject to high temperatures, such as

from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.

• Use extreme caution when drilling holes to avoid damaging fuel lines or existing

vehicle wiring.

• All amplifier installations require power, signal and speaker wires (not included).

• An amplifier installation kit (sold separately) is highly recommended to facilitate the

installation. Consult your dealer for recommendations.

Mounting Location

• Choose a mounting location for the amplifier. Suggested locations include under a seat

or in the trunk.

• The amplifier can be mounted horizontal (recommended) or vertical. For optimum

performance, make sure to provide at least 1" of space to around all sides. Do not

mount the amplifier under carpets or where airflow is restricted.

• Do not install the amplifier where it may be exposed to moisture.

• The optimum mounting location varies between vehicles. Remember to test all

amplifier functions before completing the final mounting procedure.

TYPICAL MOUNTING METHOD

NOTE

Be sure to follow specific instructions included with your amplifier installation kit

(not included with this amplifier). The information below should be used a general

guideline only.

Power Wire (+12V)

• Disconnect negative battery terminal before proceeding. Consult a qualified

technician for instructions if you are unsure.

• Plan wire routing before cutting any wires to length. Begin by routing the power

+12V wire from the battery to the amplifier location. Use a grommet when running

wires through the firewall or metal openings. Avoid running the power wire near

existing vehicle wiring to prevent induced noise from entering the audio system.

• Use extreme caution when drilling holes to avoid damaging fuel lines or existing

vehicle wiring.

• The +12V wire MUST be fused within 18" of the battery for protection of the vehicle’s

electrical system.

Ground Wire (GND)

• The amplifier ground wire should be as short as possible. Choose a clean unpainted

section of metal or the vehicle chassis when attaching the ground connection. Be

sure to clean the area of any dirt or grease.

Remote Turn-on Wire (REM)

• The remote turn-on wire connects to the head unit's amplifier turn-on lead or

power antenna output.

Speaker Wires

• Choose adequate gauge speaker wire depending on your exact amplifier/speaker

combination. Be sure to observe polarity when connecting.

• Do not ground any speaker wires or connect any speaker wires together.

Input Signal

• The amplifier's input signal connects to the head unit's low level (RCA) or high level

(speaker wire) outputs.

• Low level input signal deliver the best performance. If unavailable, use the high

level inputs - when interfacing with factory head unit for instance.

CAUTION

• Do not use both low and high level inputs at the same time - connect only one or

the other.

• Never run any wires underneath or outside the vehicle.

XPA SERIES INSTALLATION

Connection Descriptions

XPA SERIES INSTALLATION

Power and Speaker Connections

Speaker Connection(s)

Ground Connection

Remote Connection

+12VDC Battery Connection

Fuse(s)

1 234 5

4325

4 3 25

XPA2100

XPA4100

XPA6100

XPA SERIES INSTALLATION

Audio Inputs and Controls

LED Indicator

Bass Boost

Crossover Mode Switch

Crossover Frequency

Input Level Control

High Level Inputs

Low Level Inputs

Input Mode Switch

1 2 3 4 5 6 7

1 2 4 56 7

12 3 4 5

6 77

XPA2100

XPA4100

XPA6100

XPA SERIES INSTALLATION

Fuse Rating

When replacing fuses, make sure new fuse

is the correct type and amperage. Using an

incorrect fuse could damage the amplifier.

XPA2100 25 amp ATO x 1

XPA4100 25 amp ATO x 2

XPA6100 20 amp ATO x 2

Power/Ground Wire Size

For optimum performance, use only the wire

size listed below or larger. Make sure to use

the same size power and ground wire.

XPA2100 10 gauge

XPA4100 8 gauge

XPA6100 8 gauge

Main Power Connections

Connect +12V, GND and REM wires accordingly. A suitable fuse MUST be installed on the

+12V lead within 18" of the battery for protection of the vehicle’s electrical system.

Typical Wire Routing

XPA SERIES INSTALLATION

Amplifier Connections

Speaker Connections

Connect speaker wires observing

polarity. The minimum impedance

load for the XPA2100 and XPA4100

is 2 ohms stereo and 4 ohms

bridged. The minimum impedance

load for the XPA6100 is 2 ohms.

Use of loads lower than these is

not recommended and may cause

amplifier damage.The XPA2100

and XPA4100 can be wired for

stereo, bridged or stereo/bridged

simultaneous operation.

Input Signal Connections

Low Level Input (RCA)

Low level (RCA) input signal is preferred for best performance. Typical trunk-mount

amplifier installations require a 17-20 foot RCA cable. Most trucks and under-seat

applications require a 6-9 foot RCA cable. Using twisted pair construction RCA cables will

minimize noise.

High Level Input (Speaker Wire)

High level inputs should only

be used when RCA outputs are

not available from the head unit.

Connect the head unit speaker

outputs to the high level input

connector as shown below. The

black wire (signal reference ground)

may or may not require a connection

to chassis ground - depending on

your particular installation.

Subwoofer (mono)

Typical Bridged Wiring

(4 ohms minimum)

2 Speakers (stereo)

Typical Stereo Wiring

(2 ohms minimum)

CAUTION

Do not use both low and high level inputs at the same time - connect only one or the other.

XPA2100 speaker connections shown

XPA SERIES OPERATION

Configuration/Setup

The input level control (gain) is used to obtain the best

possible match between the head unit audio output and

the amplifier input. Begin by turning the input level control

fully counterclockwise. Next, turn up the head unit volume

control around 3/4 of the way up. Adjust the input level

control clockwise until audible distortion is heard, then

slightly counterclockwise to provide the best match.

Repeat for all input level controls.

Select 2 CH mode if the head unit only has 1 pair of RCA

outputs. Plug the RCA’s from the head unit into channels

1/2 or 3/4. All 4 amplifier inputs will receive a signal.

NOTE: There is no fader function when using 2 CH mode.

Select 4 CH mode if the head unit has 2 pairs of RCA

outputs. Plug the RCA’s from the head unit into channels

1/2 and 3/4.

The crossover is used to filter out frequencies above or

below a certain point. Choose LPF when using the amplifier

with subwoofers, HPF when using with midrange/tweeter

combinations and FULL when using with coaxial-type

speakers.

NOTE Choose FULL when using the amplifier in stereo/

bridged simultaneous mode. In this mode, passive

crossovers are required. Failure to use the correct passive

components may damage the amplifier and/or speakers.

Consult a qualified professional for recommendations.

This control allows precise adjustment of the crossover

frequency.

This control provides additional boost @ 45Hz when used

with subwoofers. Adjust this control with caution - as

improper use can damage speakers!

The LED indicator illuminates green during normal

operation (POWER) and red when the amplifier detects a

fault (PROTECT).

Input level Control

Input Mode Switch

(XPA4100)

Crossover Mode

(XPA2100 & XPA4100)

Crossover Frequency Control

Bass Boost

LED Indicator

XPA SERIES OPERATION

Specifications

CEA-2006 Power Standard Specifications

(reference: 14.4VDC, 20Hz~20kHz)

Power Output: 50 Watts RMS x 2 channels at 4 ohms and < 1% THD+N

Signal to noise ratio: 75dBA (reference: 1 watt into 4 ohms)

Additional power output:

75 Watts RMS x 2 channels at 2 ohms and < 1% THD+N

150 Watts RMS x 1 channel at 4 ohms (bridged) and < 1% THD+N

Dynamic power: 300 Watts at 4 ohms

Frequency response: 20Hz~20kHz (-3dB)

Maximum input signal: 6V

Minimum input signal: 200mV

Speaker output impedance: 2~8 ohms (stereo), 4~8 ohms (bridged)

Bass boost: 0~12dB @ 45Hz

Crossover range: 50~500Hz, 12dB/octave

Power supply: 11-16 VDC, negative ground

Fuse: 25 amp ATO

Amplifier dimensions: 8.9" x 2.13" x 9.17" (WxHxD)

(226 x 54 x 233 mm)

Typical installation dimensions: 11.5" x 3.25" x 9.17" (WxHxD)

(292 x 83 x 233 mm)

CEA-2006 Power Standard Specifications

(reference: 14.4VDC, 20Hz~20kHz)

Power Output: 50 Watts RMS x 4 channels at 4 ohms and < 1% THD+N

Signal to noise ratio: 72dBA (reference: 1 watt into 4 ohms)

Additional power output:

75 Watts RMS x 4 channels at 2 ohms and < 1% THD+N

150 Watts RMS x 2 channels at 4 ohms (bridged) and < 1% THD+N

Dynamic power: 600 Watts at 4 ohms

Frequency response: 20Hz~20kHz (-3dB)

Maximum input signal: 6V

Minimum input signal: 200mV

Speaker output impedance: 2~8 ohms (stereo), 4~8 ohms (bridged)

Bass boost: 0~12dB @ 45Hz

Crossover range: 50~500Hz, 12dB/octave

Power supply: 11-16 VDC, negative ground

Fuse: 25 amp ATO x 2

Amplifier dimensions: 13.69" x 2.13" x 9.17" (WxHxD)

(348 x 54 x 233 mm)

Typical installation dimensions: 16" x 3.25" x 9.17" (WxHxD)

(406 x 83 x 233 mm)

XPA2100

XPA4100

XPA SERIES OPERATION

Specifications

CEA-2006 Power Standard Specifications

(reference: 14.4VDC, 20Hz~200Hz)

Power Output: 200 Watts RMS x 1 channel at 4 ohms and < 1% THD+N

Signal to noise ratio: 72dBA (reference: 1 watt into 4 ohms)

Additional power output:

300 Watts RMS x 1 channel at 2 ohms and < 1% THD+N

Dynamic power: 600 Watts at 2 ohms

Frequency response: 20Hz~200Hz (-3dB)

Maximum input signal: 6V

Minimum input signal: 200mV

Speaker output impedance: 2~8 ohms

Bass boost: 0~12dB @ 45Hz

Crossover range: 40~200Hz, 12dB/octave

Power supply: 11-16 VDC, negative ground

Fuse: 20 amp ATO x 2

Amplifier dimensions: 13.69" x 2.13" x 9.17" (WxHxD)

(348 x 54 x 233 mm)

Typical installation dimensions: 16" x 3.25" x 9.17" (WxHxD)

(406 x 83 x 233 mm)

Design and specifications subject to change without notice.

XPA6100

Andere Handbücher für XPA2100

Inhaltsverzeichnis

Andere Dual Verstärker Handbücher

Dual

Dual DA1000D Betriebsanleitung

Dual

Dual DA560D Betriebsanleitung

Dual

Dual DA560D Betriebsanleitung

Dual

Dual DMA804D Betriebsanleitung

Dual

Dual XPR522 Bedienungsanleitung

Dual

Dual XPA2500 Betriebsanleitung

Dual

Dual DMA3100 Betriebsanleitung

Dual

Dual DBTMA100 Bedienungsanleitung

Dual

Dual XPR510D Bedienungsanleitung

Dual

Dual DPA250 Betriebsanleitung

Dual

Dual illumiNITE XIA4225 Betriebsanleitung

Dual

Dual XPE1700 Bedienungsanleitung

Dual

Dual XPE1700 Betriebsanleitung

Dual

Dual DA604D Betriebsanleitung

Dual

Dual XPA2500 Betriebsanleitung

Dual

Dual XPR522 Betriebsanleitung

Dual

Dual CV 6020 Bedienungsanleitung

Dual

Dual Compact Series Betriebsanleitung

Dual

Dual illumiNITE XIA4225 Betriebsanleitung

Dual

Dual DPA250 Betriebsanleitung

Dual

Dual DA301L Betriebsanleitung

Dual

Dual ALB12 Bedienungsanleitung

Dual

Dual XIA2340 Betriebsanleitung

Dual

Dual CV 1260 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung