Dukane 8953H Bedienungsanleitung

ENGLISH

Projector

8953H

User's Manual (concise)

Thank you for purchasing this projector.

Contents of package.................................. 1

Arrangement ............................................. 2

Connecting your devices........................... 3

Using a USB storage ................................ 4

Using an SD card ...................................... 4

Connecting power supply ......................... 5

Turning on the power................................ 5

Adjusting the projector’s elevator............. 6

Remote control.......................................... 6

Displaying the picture............................... 8

Turning off the power ............................... 8

Lamp ......................................................... 9

Air lter................................................... 11

Internal clock battery .............................. 12

Using the CD manual.............................. 13

Regulatory notices .................................. 14

Specications .......................................... 15

Warranty and after-service...................... 16

Contents

Contents of package

Your projector should come with the items shown below.

Check that all the items are included. Require of your

dealer immediately if any items are missing.

(1) Remote control with two AA batteries

(2) Power cord

(3) RGB cable

(4) Lens cover and Rivet and Strap

(5) User’s manuals (Book x1, CD x1)

(6) Security label

(7) Slot cover lock

(8) Application CD

(1) (2)

BLANK LASER

ASPECT

PUSH

ENTER

PAGEUP

LASER

INDICATOR

MYSOURCE/

DOC.CAMERA

STANDBY/ON VIDEO RGB

PAGEDOWN

ESC MENU RESET

POSITION AUTO

MAGNIFY

OFF

MYBUTTON

VOLUME

FREEZE KEYSTONE MUTE

(3) (4)

(5) (6)

 

CAUTION

►Keep the original packing materials for future reshipment. Be sure to use the original

packing materials when moving the projector. Use special caution for the lens.

WARNING

►Before using this product, be sure to read all manuals for this product. See “Using the

CD manual” (13) to read the manuals in the CD. After reading them, store them in a

safe place for future reference.

(7) (8)

NOTE

• To use the wireless network function, the designated wireless network card that is sold as an

optional is required. (15)

WARNING

►Install the projector in a stable horizontal position.

►Place the projector in a cool place, and ensure that there is sufcient ventilation.

►Do not place the projector any place where it may get wet.

CAUTION

►Avoid placing the projector in smoky, humid or dusty place.

►Position the projector to prevent light from directly hitting the projector’s remote

sensor.

Arrangement

Please arrange the projector and the screen.

Install the projector in a stable, cool and airy place, keeping a space of 30 cm or more between the

sides of the projector and other objects such as walls. Avoid the projector from a hot, humid, dusty,

or smoky place.

Refer to the illustrations and tables below to determine screen size and projection distance.

The values shown in the table are calculated for a full size screen: 1024x768

(a) Screen size (diagonal)

(b) Projection distance (±10%)

On a horizontal surface

Suspended from the ceiling

(a) Screen

size

[inch (m)]

4 : 3 screen 16 : 9 screen

(b) Projection distance

[m (inch)]

[cm (inch)]

(b) Projection distance

[m (inch)]

[cm (inch)]

min. max. down up min. max. down up

30 (0.8) 0.9 (35) 1.1 (42) 5 (2) 41 (16) 1.0 (38) 1.2 (46) -1 (0) 39 (15)

40 (1.0) 1.2 (47) 1.4 (57) 6 (2) 55 (22) 1.3 (51) 1.6 (62) -2 (-1) 51 (20)

60 (1.5) 1.8 (71) 2.2 (86) 9 (4) 82 (32) 2.0 (78) 2.4 (94) -2 (-1) 77 (30)

70 (1.8) 2.1 (83) 2.6 (100) 11 (4) 96 (38) 2.3 (91) 2.8 (110) -3 (-1) 90 (35)

80 (2.0) 2.4 (96) 2.9 (115) 12 (5) 110 (43) 2.6 (104) 3.2 (126) -3 (-1) 103 (41)

90 (2.3) 2.7 (108) 3.3 (130) 14 (5) 123 (49) 3.0 (117) 3.6 (141) -4 (-1) 116 (46)

100 (2.5) 3.0 (120) 3.7 (144) 15 (6) 137 (54) 3.3 (131) 4.0 (157) -4 (-2) 129 (51)

120 (3.0) 3.7 (144) 4.4 (174) 18 (7) 165 (65) 4.0 (157) 4.8 (189) -5 (-2) 154 (61)

150 (3.8) 4.6 (181) 5.5 (217) 23 (9) 206 (81) 5.0 (197) 6.0 (237) -6 (-2) 193 (76)

200 (5.1) 6.1 (241) 7.4 (291) 30 (12) 274 (108) 6.7 (263) 8.0 (317) -8 (-3) 257 (101)

250 (6.4) 7.7 (302) 9.2 (364) 38 (15) 343 (135) 8.4 (329) 10.1 (396) -10 (-4) 322 (127)

300 (7.6) 9.2 (363) 11.1 (437) 46 (18) 411 (162) 10.0 (395) 12.1 (476) -12 (-5) 386 (152)

350 (8.9) 10.8 (424) 13.0 (510) 53 (21) 480 (189) 11.7 (462) 14.1 (556) -15 (-6) 450 (177)

• Consult with your dealer before a

special installation such as suspending

from a ceiling.

(a) (c) up

(b)

(a)

(b)

ENGLISH

LAN

AUX I/O

DC 5V 0.5A

SD CARD

VIDEO

CONTROL

AUDIO IN1

AUDIO IN2

AUDIO OUT

RGB

OUT

RGB1

RGB2

HDMI

R L R L

AUDIO IN3 AUDIO IN4

CB/PB

CR/PR

B/CB/PB R/CR/PR

G/Y

H V

USB

REMOTE

CONTROL

S-VIDEO

RGB OUT

AUDIO OUT

RGB OUT

AUDIO OUT

RS-232C

LAN

RGB IN

AUDIO IN

Y CB/PBCR/PR

COMPONENT VIDEO OUT

R L

AUDIO OUT

VIDEO OUT

S-VIDEO OUT

HDMI USB-A

R L

AUDIO OUT

R L

AUDIO OUT

Connecting your devices

Before connecting devices, please read the manuals for all the devices that you want to connect with

this projector, to make sure that the connection is proper and prepare the connectors needed. And

connect them properly according to the manuals.

Monitor

Remote

control

Speakers

(with an

amplier)

VCR/DVD player

WARNING

►Do not disassemble or modify the projector and accessories.

►Be careful not to damage the cables, and do not use damaged cables.

CAUTION

►Turn off all devices and unplug their power cords prior to connecting them to

projector.

►Use appropriate accessory or designated cables. Ask your dealer about non-accessory

cables which may be required a specic length or a ferrite core by the regulations. For

cables with a core only at one end, connect the end with the core to the projector.

►Make sure that devices are connected to the correct ports.

BLANK LASER

ASPECT

PUSH

ENTER

PAGEUP

LASER

INDICATOR

MYSOURCE/

DOC.CAMERA

STANDBY/ON VIDEO RGB

PAGEDOWN

ESC MENU RESET

POSITION AUTO

MAGNIFY

OFF

MYBUTTON

VOLUME

FREEZE KEYSTONE MUTE

USB storage

SD card

SD card slot cover

(SD card slot inside) AUX I/O port

Using a USB storage

In order to view images stored in a USB storage, such as

a USB memory, insert the device into the AUX I/O port.

Before removing the USB storage, be sure to perform

the REMOVE MEDIA procedure using the PC-LESS

PRESENTATION menu under the MIU menu.

Using an SD card

In order to view images stored in an SD storage, such as an SD memory card, insert the device into

the SD card slot. Or, in order to use the wireless network function, load the internal clock battery

(12)and insert the designated wireless network card that is sold as an option (15)into the slot.

SD CARD

Angled corner

Removing the SD card

1. Perform the REMOVE MEDIA procedure using the PC-LESS PRESENTATION menu under

the MIU menu for SD storage card only.

2. Turn the projector off and unplug the power code from the projector for the wireless network

card only.

3. Remove the SD card slot cover. After taking the SD card away, replace the SD card slot cover.

Inserting the SD card

1. Make sure that the power code is not plugged into the projector for the wireless

network card only.

2. Remove the SD card slot cover. After slowly insert the SD card completely into

the SD card slot, replace the SD card slot cover.

Using the slot cover lock for security

Using the enclosed slot cover lock can prevent the SD card slot cover from being

opened.

1. Open the two plates of the slot cover lock to put the tips of two plates together,

and then insert the tips to the lock hole of the SD card slot cover.

2. Put the body of the two plates together. Then, hook a padlock or combination

lock to the hole of the slot cover lock.

CAUTION

►Do not touch the SD card while being accessed.

►To use the wireless network function, the designated wireless network card that is

sold as an option is required.

• The wireless network card is not permitted to be sold or used in some countries

and regions. Use the card only in the country or region where you buy it. For more

information, ask your local dealer.

• When using the wireless network card, to comply with FCC RF exposure compliance

requirements, the antenna used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must not be co-located or

operating in conjunction with any other antenna or transmitter.

• Before using the projector with a wired LAN, remove the wireless network card.

ENGLISH

Connecting power supply

1. Connect the connector of the power cord to the AC IN

(AC inlet) of the projector.

2. Firmly plug the power cord's plug into the outlet.

AC IN

to the outlet

Connector of the

power cord

Turning on the power

1. Make sure that the power cord is rmly and correctly connected

to the projector and the outlet.

2. Remove the lens cover, and set the power switch to the ON

position (marked “ I”).

The POWER indicator will light up in steady orange. Then

wait several seconds because the buttons may not function for

these several seconds.

3. Press the STANDBY/ON button on the projector or the remote

control.

The projection lamp will light up and the POWER indicator will

begin blinking in green. When the power is completely on, the

indicator will stop blinking and light in steady green.

STANDBY/ON button

POWER indicator

NOTE

• When the AUTO ON in the OPTION menu is set to the TURN ON, and the power was turned

off by the power switch last time, turning the power switch on makes the projection lamp light

on without pushing the STANDBY/ON button. For more information, please see the “Operating

Guide” in the CD.

Power

switch

WARNING

►A strong light is emitted when the projector’s power is on. Do not look into the lens

of the projector or look inside of the projector through any of the projector’s openings.

WARNING

►Please use extra caution when connecting the power cord, as incorrect or faulty

connections may result in re and/or electrical shock.

• Only use the power cord that came with the projector. If it is damaged, consult your

dealer to get a new one.

• Only plug the power cord into an outlet whose voltage is matched to the power cord.

The power outlet should be close to the projector and easily accessible. Remove the

power cord for complete separation.

• Never modify the power cord.

BLANK LASER

ASPECT

PUSH

ENTER

PAGEUP

LASER

INDICATOR

MYSOURCE/

DOC.CAMERA

STANDBY/ON VIDEO RGB

PAGEDOWN

ESC MENU RESET

POSITION AUTO

MAGNIFY

OFF

MYBUTTON

VOLUME

FREEZE KEYSTONE MUTE

BLANK LASER

ASPECT

PUSH

ENTER

PAGE UP

LASER

INDICATOR

MYSOURCE/

DOC.CAMERA

STANDBY/ON VIDEO RGB

PAGE DOWN

ESC MENU RESET

POSITION AUTO

MAGNIFY

OFF

MY BUTTON

VOLUME

FREEZE KEYSTONE MUTE

Adjusting the projector's elevator

Use the elevator feet to place the projector horizontally. Using the feet can also

tilt the projector in order to project at a suitable angle to the screen, elevating

the front side of the projector within 10 degrees.

This projector has 2 elevator feet and 2 elevator knobs. An elevator foot is

adjustable while pulling up the elevator knob on the same side as it.

1. To loose an elevator foot, pull up the elevator knob on the same side as it.

2. Position the front side of the projector to the desired height.

3. Release the elevator knobs in order to lock the elevator feet.

4. To nely adjust, twist the foot.

Remote control

Laser pointer

The laser beam is emitted and the LASER INDICATOR lights while the LASER button is pressed.

LASER INDICATOR

LASER button

The laser beam outlet

WARNING

►Do not handle the elevator knobs without holding the projector, since the projector

may drop down.

►Do not tilt the projector other than elevating its front within 10 degrees using the

adjuster feet. A tilt of the projector exceeding the restriction could cause malfunction or

shortening the lifetime of consumables, or the projector itself.

WARNING

►Never hit an eye with the laser beam, and use the laser pointer except to serve as

a pointer to a screen. The laser beam can cause vision problems, and also may cause

radiation exposure.

10°

ENGLISH

Putting batteries

Please load the batteries before using the remote control.

1. Slide back and remove the battery cover.

2. Put the two AA batteries

into the holder, according to the polarity markings (+) and (-) on the holder.

3. Put the battery cover back to its former state.

Remote control (continued)

Buttons

(1) STANDBY/ON button

(2) VIDEO button (3) RGB button

(4) MY SOURCE/DOC.CAMERA button

(5) SEARCH button (6) BLANK button

(7) LASER button (8) ASPECT button

(9) Lever switch : acting 3 functions as below.

Cursor button ▲ : to slide toward the side marked ▲.

Cursor button ▼ : to slide toward the side marked ▼.

ENTER button : to push down the center point.

(10) Cursor button ◄ (11) Cursor button ►

(12) PAGE UP button (13) PAGE DOWN button

(14) ESC button (15) MENU button

(16) RESET button (17) POSITION button

(18) AUTO button

(19) MAGNIFY ON/OFF button

(20) MY BUTTON 1 button (21) MY BUTTON 2 button

(22) VOLUME +/-button (23) FREEZE button

(24) KEYSTONE button (25) MUTE button

BLANK LASER

ASPECT

PUSH

ENTER

PAGE UP

LASER

INDICATOR

MY SOURCE/

DOC.CAMERA

STANDBY/ON VIDEO RGB

PAGE DOWN

ESC MENU RESET

POSITION AUTO

MAGNIFY

OFF

MY BUTTON

VOLUME

FREEZE KEYSTONE MUTE

(6)

(1) (3)

(18)

(23)

(16)

(14)

(21)

(8) (9)

(11)

(12)

(15)

(17)

(19)

(7)

(10)

(13)

WARNING

►Always handle the batteries with care and use them only as directed. Improper use

may result in battery explosion, cracking or leakage, which could result in re, injury

and/or pollution of the surrounding environment.

• Be sure to use only the batteries specied. Do not use batteries of different types at the

same time. Do not mix a new battery with used one.

• Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

• Do not place a battery in a re or water. Keep batteries in a dark, cool and dry place.

• If you observe battery leakage, wipe out the leakage and then replace a battery. If the

leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

(2) (4)

(5)

(24)

(22)

(20)

(25)

Displaying the picture

1. Make sure that the signal source is sending the signal to the

projector.

2. Use the VOLUME +/- buttons to adjust the volume. To have the

projector silent, press the MUTE button on the remote control.

3. Press the INPUT button on the projector.

Each time you press the button, the projector switches its input

port in turn.

4. Press the ASPECT button on the remote control. Each time you

press the button, the projector switches the mode for aspect ratio

in turn.

5. Use the zoom ring to adjust the screen size.

6. Use the focus ring to focus the picture.

7. Use the vertical lens shift dial to shift the picture upward or

downward. It is recommended to adjust the picture upward.

8. Use the horizontal lens shift dial to shift the picture left or right.

ASPECT

button

INPUT button

Focus ringZoom ring

Top

Turning off the power

1. Press the STANDBY/ON button on the projector or the remote

control.

The message “Power off?” will appear on the screen for about

5 seconds.

2. Press the STANDBY/ON button on the projector or the remote

control again while the message appears.

The projector lamp will go off, and the POWER indicator will

begin blinking in orange.

Then the POWER indicator will stop blinking and light in

steady orange when the lamp cooling is complete.

3. Make sure that the POWER indicator lights in steady orange,

and set the power switch to the OFF position (marked “O”).

The POWER indicator will go off. Attach the lens cover.

Do not turn the projector on for 10 minutes or more after turning it off. Turning the projector on

again too soon could shorten the lifetime of some consumable parts of the projector.

STANDBY/ON button

POWER indicator

Power

switch

BLANK LASER

ASPECT

PUSH

ENTER

PAGE UP

LASER

INDICATOR

MYSOURCE/

DOC.CAMERA

STANDBY/ON VIDEO RGB

PAGE DOWN

ESC MENU RESET

POSITION AUTO

MAGNIFY

OFF

MYBUTTON

VOLUME

FREEZE KEYSTONE MUTE

BLANK LASER

ASPECT

PUSH

ENTER

PAGEUP

LASER

INDICATOR

MYSOURCE/

DOC.CAMERA

STANDBY/ON VIDEO RGB

PAGEDOWN

ESC MENU RESET

POSITION AUTO

MAGNIFY

OFF

MYBUTTON

VOLUME

FREEZE KEYSTONE MUTE

WARNING

►

Do not touch around the lamp cover and the exhaust vents during use or just after use,

since it is too hot.

MUTE button

VOLUME +/-buttons

Lens shift cover

2/5

1/10

DOWN

LEFT RIGHT

ENGLISH

Lamp

A lamp has nite product life. Using the lamp for long periods of time could cause the pictures

darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or

burn out soon after you start using them.

Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, make

contact with your dealer and tell the lamp type number.

Type number = 456-8949H

Replacing the lamp

1. Turn the projector off, and unplug the power cord. Allow the

projector to cool for at least 45 minutes.

2. Prepare a new lamp.

If the projector is mounted on a ceiling, or if the lamp has

broken, also ask the dealer to replace the lamp.

In case of replacement by yourself,

3. Loosen the screw (marked by arrow) of the lamp cover and

then slide the lamp cover to the side to remove it.

4. Loosen the 3 screws (marked by arrow) of the lamp, and

slowly pick up the lamp by the handles.

5. Insert the new lamp, and retighten rmly the 3 screws of the

lamp that are loosened in the previous process to lock it in

place.

6. Slide the lamp cover back in place and rmly fasten the

screw of the lamp cover.

7. Turn the projector on and reset the lamp time using the

LAMP TIME item in the OPTION menu.

(1) Press the MENU button to display a menu.

(2) Point at the “Go to Advanced Menu …” in the menu

using the ▼/▲ button, then press the ► button.

(3) Point at the “OPTION” in the left column of the menu

using the ▼/▲button, then press the ► button.

(4) Point at the “LAMP TIME” using the ▼/▲ button, then

press the ► button. A dialog will appear.

(5) Press the ▲ button to select “RESET” on the dialog. It

performs resetting the lamp time.

NOTE

• Please reset the lamp time only when you have replaced the lamp, for a suitable indication about

the lamp.

The lamp cover

The handles

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

►The projector uses a high-pressure mercury glass lamp. The lamp can break with a

loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.

Note that each lamp has a different lifetime, and some may burst or burn out soon

after you start using them. In addition, when the bulb bursts, it is possible for shards of

glass to y into the lamp housing, and for gas containing mercury to escape from the

projector’s vent holes.

• If the lamp should break (it will make a loud bang when it does),

Unplug the power cord from the outlet, and make sure to request a

replacement lamp from your local dealer. Note that shards of glass could

damage the projector’s internals, or cause injury during handling, so please

do not try to clean the projector or replace the lamp yourself.

Ventilate the room well, and make sure not to breathe the gas that comes

out of the projector vents, or get it in your eyes or mouth.

• Before replacing the lamp, turn the projector off and unplug the power

cord, then wait at least 45 minutes for the lamp to cool sufciently.

Handling the lamp while hot can cause burns, as well as damaging the

lamp.

• Never unscrew except the appointed (marked by an arrow) screws.

• Do not open the lamp cover while the projector is suspended from a

ceiling. This is dangerous, since if the lamp’s bulb has broken, the shards

will fall out when the cover is opened. In addition, working in high places

is dangerous, so ask your local dealer to have the lamp replaced even if the

bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp

replacing, make sure that the screws are screwed in rmly. Loose screws

could result in damage or injury.

• Use only the lamp of the specied type.

• If the lamp breaks soon after the rst time it is used, it is possible that there

are electrical problems elsewhere besides the lamp. If this happens, consult

your local dealer or a service representative.

• Handle with care: jolting or scratching could cause the lamp bulb to burst

during use.

• Using the lamp for long periods of time, could cause it dark, not to light up

or to burst. When the pictures appear dark, or when the color tone is poor,

please replace the lamp as soon as possible. Do not use old (used) lamps;

this is a cause of breakage.

► About disposal of a lamp: This product contains a mercury lamp; do not put it in

a trash. Dispose of it in accordance with environmental laws.

· For lamp recycling, go to www.lamprecycle.org (in the US).

· For product disposal, consult your local government agency or www.eiae.org (in the

US) or www.epsc.ca (in Canada).

For more information, ask your dealer.

Disconnect the

plug from the

power outlet

Lamp (continued)

Lamp warning

Inhaltsverzeichnis

Andere Dukane Projektor Handbücher

Dukane

Dukane DPS1 Bedienungsanleitung

Dukane

Dukane ImagePro 8053 Bedienungsanleitung

Dukane

Dukane ImagePro 8746A Bedienungsanleitung

Dukane

Dukane ImagePro 8768 Bedienungsanleitung

Dukane

Dukane ImagePro 8914 Bedienungsanleitung

Dukane

Dukane 8107WIB Bedienungsanleitung

Dukane

Dukane ImagePro 9015 Bedienungsanleitung

Dukane

Dukane ImagePro 8755C Bedienungsanleitung

Dukane

Dukane ImagePro 8101H Bedienungsanleitung

Dukane

Dukane ImagePro 8944 Bedienungsanleitung

Dukane

Dukane 8142WISS Bedienungsanleitung

Dukane

Dukane ImagePro 8066 Bedienungsanleitung

Dukane

Dukane ImagePro 8046 28A8046 28A8046 Bedienungsanleitung

Dukane

Dukane 8793H Bedienungsanleitung

Dukane

Dukane ImagePro 8915 8915 8915 Bedienungsanleitung

Dukane

Dukane 6655WU Bedienungsanleitung

Dukane

Dukane ImagePro 8940 Bedienungsanleitung

Dukane

Dukane ImagePro 9020 Bedienungsanleitung

Dukane

Dukane ImagePro 8055 Bedienungsanleitung

Dukane

Dukane ImagePro 8947 Bedienungsanleitung

Dukane

Dukane ImagePro 8918 Bedienungsanleitung

Dukane

Dukane 8111H Bedienungsanleitung

Dukane

Dukane ImagePro 8755D-RJ Bedienungsanleitung

Dukane

Dukane ImagePro 8763 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung