Duratuf SG2525 Bedienungsanleitung

ASSEMBLY INSTRUCTIONS

SG2525

BASE SIZE: 2.520m x 2.520m

BEFORE YOU START:

 Read all instructions carefully

 Identify all parts and check quantities against parts list

 Select a level site

 Do not mark cladding with pencil as lead can cause corrosion to cladding

 During assembly, ensure all drill filings are removed between layers of steel, before riveting together

SAFETY:

 Do not attempt to build your shed in high winds

 Beware of sharp edges, recommend use of gloves

 Protect your eyes and ears

 For ease of assembly, use a friend to help

TOOLS REQUIRED:

WARRANTY REQUIREMENTS:

Following are the minimum requirements for cladding used in Sentry Sheds.

 Wash all surfaces annually using a hose and soft nylon brush.

 Within 2 km of coast – wash every 3 months as above. After a storm, wash the cladding and the gutters as soon

as possible to remove any highly corrosive salt deposits.

 Volcanic Ash Fallout – wash as soon as possible, removing fall out from roof and gutters.

 Do not allow manures, chemicals or other corrosive materials to have direct contact with cladding.

DRILL RIVETER 3.5 DRILL BIT

HAMMER

LADDER

TAPE MEASURE PEN

NAIL PUNCH

CONGRATULATIONS ON PURCHASING A DURATUF SENTRY SHED.

BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS

SQUARE DRILL BIT

SG2525 PARTS LIST

DESCRIPTION QTY DIAGRAM DESCRIPTION QTY DIAGRAM

CLADDING FLASHINGS

Front/Back Wall

1.850 m 8

Door Side

1.810 m 2

Gable Wall Angled

1.880 m (Measurement along

centre of sheet) 4

Door Jamb

1.850 m 2

Gable Wall Angled

1.940 m (Measurement along

centre of sheet) 4

Door Brace

1.160 m 2

Gable Wall Angled

2.000 m (Measurement along

centre of sheet) 2

Barge

1.350 m 4

Roof

1.350 m 10

Ridge Flashing

1.555 m 2

Door 3/4 Sheet

1.810 m 2

Padbolt Support

0.140 m 1

TIMBER

Spouting

2.555 m 2

Bottom Plates - H4 (Green)

Front/Back

2.520 m 2

HARDWARE

Bottom Plates - H4 (Green)

Sides

2.520 m 2

Hardware Pack 1

Top Plate - H1 (Red)

Front/Back

2.520 m 2

Paint & Brush 1

Top Plate - H1 (Red)

Sides

2.520 m 2

Ridge Beam - H1

90 x 45

2.520 m 1

Jack Studs - H1

45 x 60

0.200 m 2

Bolt Down Kit 1

FLASHINGS

Door Top/Bottom

0.945 m 2

DATE:

PACKED BY:

OPTIONAL

CHECKED

PARTS LOCATION

Door Sheets

Padbolt Support

Top Plate Back

Side Wall Sheets

Barge Flashing

Spouting

Roof Sheets

Top Plate Side

Top Plate Front

Bottom Plate Front

Bottom Plate Side

Back Wall Sheets

Front Wall Sheets

Door Jambs

Front Wall Sheet

Door Side Flashing Hinge

Door Brace

Door Top/Bottom

Ridge Beam

Jack Stud

Ridge Flashings - x 2

ASSEMBLE FRONT

PANEL

ASSEMBLE WALLS

ASSEMBLE ROOF

SECURE SHED

ASSEMBLE BACK

PANEL

ASSEMBLE SIDE

PANELS

LAY FOUNDATION

ASSEMBLE DOOR

QUICK OVERVIEW

FOUNDATION

SENTRY WOODEN FLOOR

 The optional Sentry kitset wooden floor is precut and designed to

be fitted into the shed after the shed is assembled.

 Assemble shed as per instructions and fit floor last.

(see page 13 for details).

CONCRETE SLAB FOR RAISED BASE PLATE SHED

To build a raised concrete slab for your shed to sit on, we recom-

mend the following:

 The raised slab size should be 15mm smaller than the base

size of the shed and at least 30mm above ground line.

 The slab should be 80mm thick in the middle and 100mm

thick around the edges.

 The slab should be laid on a solid or compacted base.

 Plastic sheeting under slab will prevent moisture coming

through from underneath.

 During construction, you may raise the bottom timber

plate to allow the wall cladding to protrude 20mm below

the bottom plate. This will stop water flowing between

the bottom plate and the concrete floor.

See note on page 7.

80mm

100mm

7.5mm

20mm

Concrete Floor

Base Plate

Wall Cladding

RAISED BASE PLATE OPTION

(For sheds placed on a raised concrete floor)

No doubt by now you will have decided what sort of base you are putting down.

Please read the section that applies to your situation.

If you choose to pour a concrete base you will need to decide whether you wish to raise the base plate of your shed.

This allows the cladding to protrude below the surface of the concrete and ensures a water tight pad.

See concrete pad specifications below

By choosing this option you will need to make the pad to the specification below.

ASSEMBLE DOOR

SELECT:

2 x 1.810 m Door Sheets (Narrow)

2 x 0.945 m Door Top/Bottom Flashings

2 x 1.810 m Door Side Flashings

3 x Hinges

1 x Padbolt Support Flashing

2 x 1.160 m Door Brace Flashings

54 x Rivets

STEP 1:

 Lay out door sheets on a flat surface

making sure narrow pans are on the

outside.

 Rivet sheets together in the centre en-

suring ends are flush with each other.

STEP 2:

 Position door side flashings and top

and bottom flashings and assemble

door as shown.

 Drill and rivet as per diagram.

STEP 4:

 On the back of the door, place door braces in posi-

tion as shown in fig.3.

 Ensure that the top and bottom ends of the braces

are under the door flashings as shown in fig.4. and

opposite ends of the braces overlap in the middle.

 Rivet door brace flashings onto back of door as

shown. Where possible, rivet from front of door.

fig.1

STEP 3:

 Attach hinges to door side flashing using rivets provided.

Ensure hinge is flush with back of door, and 60mm in from

each end as per fig.2.

 Using one rivet, attach padbolt support as shown in fig. 1.

NARROW PANS

fig.3

fig.4

fig.2

ASSEMBLE SIDE PANELS

SELECT:

4 x 1.880 m Gable Wall Sheets (Angled)

4 x 1.940 m Gable Wall Sheets (Angled)

2 x 2.000 m Gable Wall Sheets (Angled)

2 x 2.520 m Top Plates (Red)

2 x 2.520 m Bottom Plates (Green)

120 x 30mm Galv Clouts

16 x Rivets

IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER

BASE PLATE –READ THE FOLLOWING;

For sheds with Raised Base Plate option only (see page 5), deduct

30mm from measurement shown between Top and Bottom Plates on

all wall panels, so cladding protrudes 20mm below bottom plate.

STEP 1:

 Lay out 1 x Top plate and 1 x Bottom plate on a flat surface as shown

(corner cut-outs to face outwards). Measurements between Top and

Bottom plates are critical to ensure wall panels fit together.

STEP 2:

 Place 2 x 1.880 m wall sheets, 2 x 1.940 m wall sheets and 1 x

2.000m wall sheet on top of timber plates with bottom of sheets

flush with each other.

 Rivet sheets together on overlaps as shown.

STEP 3:

 Nail wall sheets to the Top Plate at each end making

sure that the top corners of the sheets are flush with

the top of the Top Plate and that the sides of the wall

sheet overhang the Top Plate by approx 15mm as

shown.

 Check that the Top Plate is straight then nail the

Wall sheet to the Top Plate, 2 clouts per pan.

(see fig. 1).

Std Shed — Bottom Plate will protrude below

wall sheet by approximately 10mm.

Raised base plate shed — Wall sheet will protrude

below the Bottom Plate by 20mm.

STEP 4:

 Nail the wall sheets to the Bottom Plate at each end ensuring each side

of wall sheets overhangs the end of Bottom Plate by 15mm. Check that

the distance between the Top and Bottom Plates is correct. (As per

diagram in step 1)

 Check that the Bottom Plate is straight then nail the wall sheets to the

Bottom Plate, two clouts per pan (see fig. 1).

fig.1

RIB

PAN

CLOUT

TIMBER PLATE

TOP PLATE

BOTTOM PLATE

RIVET

RIVET RIVET

TOP PLATE

15mm 15mm

BOTTOM PLATE

1810mm 1810mm

TOP PLATE

BOTTOM PLATE

15mm 15mm

1810mm 1810mm

TOP PLATE

REPEAT THESE STEPS TO MAKE SECOND SIDE WALL PANEL

15mm

RIVET

ASSEMBLE BACK PANEL

SELECT:

5 x 1.850m Wall Sheets

1 x 2.520 m Top Plate (Red)

1 x 2.520 m Bottom Plate (Green)

60 x 30mm Galv Clouts

8 x Rivets

STEP 1:

 Lay out 1 x Top Plate and 1 x Bottom Plate on a

flat surface as shown (corner cutouts to face in-

wards).

STEP 2:

 Place 5 x 1.850 m wall sheets on top of timber

Plates with bottom of sheets flush with each other.

 Rivet the sheets together on overlaps as shown.

STEP 3:

 Nail the wall sheets to the Top Plate at each end making sure

that the top of the sheets are flush with the top of the Top

Plate and that the sides of the wall sheets overhang the Top

Plate by 15mm as shown.

 Check that the Top Plate is straight then nail wall sheets to

the Top Plate, using two clouts per pan.

STEP 4:

 Nail the wall sheets to the Bottom Plate at each end,

ensuring that each side of the wall sheets overhangs the

Bottom Plate by 15mm and that the distance between

the Top and Bottom Plates is correct. (As shown)

 Check that the Bottom Plate is straight then nail

wall sheets to the Bottom Plate, using two clouts per pan.

Std Shed — Bottom Plate will protrude below wall sheet by

approximately 10mm.

Raised base plate shed — Wall sheet will protrude below

the Bottom Plate by 20mm.

TOP PLATE

BOTTOM PLATE

1811mm 1811mm

TOP PLATE

15mm 15mm

1811mm 1811mm

BOTTOM PLATE

15mm 15mm

TOP PLATE

IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER

BASE PLATE –READ THE FOLLOWING;

For sheds with Raised Base Plate option only (see page 5), deduct

30mm from measurement shown between Top and Bottom Plates on

all wall panels, so cladding protrudes 20mm below bottom plate.

TOP PLATE

ASSEMBLE FRONT PANEL

BOTTOM PLATE

1811mm 1811mm

15mm 15mm

530mm 960mm

TOP PLATE

DOOR OPENING

SELECT:

3 x 1.850 Wall Sheets

1 x 2.520 Top Plate (Red)

1 x 2.520 Bottom Plate (Green)

2 x 1.850 Door Jamb Flashings

40 x 30mm Galv Clouts

19 x Rivets

STEP 1:

 Lay out 1 x Top Plate and 1 x Bottom Plate on a flat

surface as shown

STEP 2:

 Using 2 x 30mm clouts, nail the Door Jamb Flashing flush with

the top of the Top Plate at the correct measurement as shown

in plan view. Pre drill holes using a 3.5mm drill bit.

 Check the distance between the top and bottom plates then use

a further 2 x 30mm clouts to nail the Door Jamb Flashings to

the bottom Plate. Pre drill holes.

NOTE: Door can be hinged on either side.

STEP 4:

 Place the door on the panel (In open position, approx

20mm below top of top plate). Using two rivets, rivet the top

and bottom hinges to the Door Jamb Flashing, ensuring

door closes properly.

 Fit remaining rivets.

STEP 3:

 Place 3 x Wall Sheets on timber plates and rivet the sheets

together as shown.

 Ensure that the top of the sheet is flush with the top of the

Top Plate and that the sides of the wall sheet overhang the

Top Plate by 15mm as shown. Nail wall sheets to Top Plate

(two clouts per pan).

 Nail the wall sheets to the Bottom Plate making sure that the

Plates are the correct distance apart and that the sides of the

wall sheets overhang the Bottom Plate by 15mm.

 Drill & rivet Door Jamb Flashings to wall sheets using four

rivets equally spaced on each side.

NOTE: The Doorway is standard at 530mm from left-hand end.

To shift the doorway to the right-hand side of the front

wall, simply measure 530mm from the right-hand end.

Plan View

IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER

BASE PLATE –READ THE FOLLOWING;

For sheds with Raised Base Plate option only (see page 5), deduct

30mm from measurement shown between Top and Bottom Plates on

all wall panels, so cladding protrudes 20mm below bottom plate.

TOP PLATE

TOP

PLATE

DOOR

JAMB

NAIL

Inhaltsverzeichnis

Andere Duratuf Außenlagerung Handbücher

Duratuf

Duratuf PL44 Bedienungsanleitung

Duratuf

Duratuf PG66 Bedienungsanleitung

Duratuf

Duratuf Smart store SS1507 Bedienungsanleitung

Duratuf

Duratuf SL2515 Bedienungsanleitung

Duratuf

Duratuf TUF 400 Bedienungsanleitung

Duratuf

Duratuf GARRISON PS62 Bedienungsanleitung

Duratuf

Duratuf SL1520 Bedienungsanleitung

Duratuf

Duratuf Garrison PL63 Bedienungsanleitung

Duratuf

Duratuf Garrison PL36 Bedienungsanleitung

Duratuf

Duratuf Garrison Sheds PL64 Bedienungsanleitung

Duratuf

Duratuf MK4 Bedienungsanleitung

Duratuf

Duratuf PG96 Bedienungsanleitung

Duratuf

Duratuf GG97 Bedienungsanleitung

Duratuf

Duratuf GUARDIAN SHED GL37 Bedienungsanleitung

Duratuf

Duratuf Gurdian Sheds GG101 Bedienungsanleitung

Duratuf

Duratuf SG3025 Bedienungsanleitung

Duratuf

Duratuf PG88 Bedienungsanleitung

Duratuf

Duratuf TUF LOCKER Bedienungsanleitung

Duratuf

Duratuf KAIPARA Bedienungsanleitung

Duratuf

Duratuf PG98 Bedienungsanleitung

Duratuf

Duratuf SENTRY SS2007 Bedienungsanleitung

Duratuf

Duratuf TUF 50 Bedienungsanleitung

Duratuf

Duratuf SG3020 Bedienungsanleitung

Duratuf

Duratuf GS62 Bedienungsanleitung

Beliebte Außenlagerung Handbücher anderer Marken

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Bedienungsanleitung

TYGO

TYGO Nyland Bedienungsanleitung

Viking

Viking SD5300SS Technisches Handbuch

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Bedienungsanleitung

ModuLaro

ModuLaro Lojo WC202200 Bedienungsanleitung

Lifetime

Lifetime 6418 Bedienungsanleitung

rollaway container

rollaway container ARPCA24 Bedienungsanleitung

X-METAL

X-METAL 4065 Bedienungsanleitung

Outdoor Life Products

Outdoor Life Products FP2030 F Bedienungsanleitung

Royalcraft

Royalcraft Faro 295L Storage Box Bedienungsanleitung

Riverlea

Riverlea Duratuf KIWI KS3 Bedienungsanleitung

Rubbermaid

Rubbermaid 5L45 Bedienungsanleitung

garofalo

garofalo TUSCANY EVO Bedienungsanleitung

OLT

OLT GS84D-FJ-Plywood Bedienungsanleitung

Eden

Eden CA2988 Bedienungsanleitung

Palram

Palram CANOPIA RUBICON 6x10 Administratorhandbuch

Suncast

Suncast 774098 Bedienungsanleitung

Lifetime

Lifetime 60186 Bedienungsanleitung