Suncast 774098 Bedienungsanleitung

Questions? Call toll-free 866-768-8465

Monday-Friday, 8:00 a.m. to 5:00 p.m. EST

8x8 Wooden Shed

Assembly Manual

(Shown with customer-supplied paint and shingles)

0660154

ITM./ART. 774098

page 2

Before You Begin...

•Consult your local authorities for any permits required to construct shed.

Prior to the construction of your shed, check with the local building code ofﬁcial to review any required

permits or building limitations.

•A level foundation is required before shed construction can begin.

Crushed Rock is required as a base. It should be 3/4 inch stone, at least 4 inches deep. It is very

important to assemble the unit on a ﬁrm, level surface.

•Read instructions thoroughly prior to assembly.

This kit contains parts that can be damaged if assembled incorrectly or in the wrong sequence. Suncast

is not responsible for replacing parts lost or damaged due to incorrect assembly.

•Check for all parts before you begin assembly.

Using the provided parts check list on pages 4 - 7 verify that you have all the parts required to construct

your shed model. COMPLETE SITE PREPARATION BEFORE UNPACKING ALL PARTS.

•This product contains parts that are used in different orientations to construct the shed.

Please take note of the orientation of the parts shown throughout this instruction manual. Failure to follow

instructions could result in damage to parts. Suncast is not responsible for replacing parts lost or

damaged due to incorrect assembly.

•Gather required tools as listed on page 3.

•Shingles and paint not included. Follow manufacturer’s recommendation

for application of shingles and paint when shed assembly is complete.

• Assistance is required during entire assembly. Three people recommended.

CAUTION

• Proper site preparation required.

• Shed not intended for storage of ﬂammable or caustic chemicals.

• Store heavy items near the bottom of shed.

• Shed not intended for use by children.

• DO NOT stand, sit, or store items on storage shed roof.

• Repair or replace broken parts immediately.

• Suncast is not responsible for damage caused by weather or misuse.

• At regular intervals inspect your shed to make sure that assembly integrity has been maintained.

• Periodically check that the location you have chosen to set your shed is still level.

• This kit contains parts with metal edges. Please be careful when handling.

• Hot items, such as recently used grills, blowtorches, etc., must not be stored in the shed.

IMPORTANT

•Basic carpentry skills are required to construct this shed. Professional installation is

recommended if you are unfamiliar with basic wood-frame construction.

Shed Safety and Care

• Unit must be stored completely packaged in a cool, dry place until ready to assemble.

• Many wood pieces (e.g. wall studs) are able to be installed with either end up or down, or turned 180

degrees. In these cases, look at the pieces before attaching them and decide which position is best.

For example, you may hide a blemish on a stud by fastening siding to that side of the stud.

• Look at all the trim pieces before installing, and choose the best ones for the front of the shed.

• Keep roof clean of snow and leaves.

Assembly Day Tips

• Complete site preparation before unpacking parts and beginning assembly.

• DO NOT attempt to assemble on a day with strong winds.

• DO NOT attempt to assemble on days when temperature is below 32 degrees.

• Wear light duty work gloves while assembling shed.

page 3

Piezas – BMDB12000

Tools needed for installation

5/32

Tools Needed for Installation

• Set aside an appropriate amount of time to completely assemble the shed. Assembly

time is about 8 hours with two experienced people and the use of air-powered tools.

While air tools were used to assemble much of the unit in this manual, the unit can also

be assembled with hand tools.

Assembly Day Tips

page 4

FLOOR

Quantity Description

7 Joists: Pressure-Treated 2x4, 93-1/2”L

2Band Boards: Pressure-Treated 2x4, 96”L with dados

16” on center

2Floor Decking: LP Smart Floor,

48” x 96” sheets

WALL FRAMING

4 Top/ bottom plates: 2x4, 96” L with dados 24” on center

2 Top/ bottom plates: 2x4, 89” L with dados for window

1 Top plate: 2x4, 89” L with dados for door

2 Bottom plate: 2x4, 14-3/4” L with dados for door

16 Studs: 2x4, 72” L

2 Studs: 2x4, 72”L with dados for window

4 Corner blocks: 2x4, 15”L with notch

1 Door header: 2x4, 59-1/2” L

1 Framing vertical above window: 2x4, 4”L

1 Framing vertical below window: 2x4, 42-3/4”L

2Window horizontal framing: 2x4, 18-3/4”L, with dados

for vertical parts

2 Gable braces: 2x4, 24-1/2”L, with angle cuts

Parts

WALL FRAMING CONTINUED

Quantity Description

2 Gable braces: 2x4, 17”L

2Sofﬁt: 9/16” thick plywood, 5-3/4” x 96” with dados for

rafters

WALL SIDING

4 Siding for side walls: 48” x 75-1/2”

2Siding for gable end: 48” x 96” with window cutouts and

angle cuts

2Siding for gable end: 48” x 96” with door cutouts and

angle cuts

4 Filler piece for gable ends: 3” x 14” with angle cuts

4 Filler piece for gable ends: 2” x 2”

page 5

ROOF

Quantity Description

10 Rafters: 2x4, 55-7/8”L with heel and angle cuts

Gussets: 6” x 16” OSB with angle cuts (2 also with

special cutout for vent)

Roof Sheeting: 48” x 96” OSB

2Roof Sheeting: 7-3/4” x 96” OSB

4Drip Edge: 57-1/2”

4Drip Edge: 51”

Felt paper for roof: 40’

LOFT

1 Framing: 2x4, 96”L with notch on each end

1 Loft decking: 24” x 89” OSB

TRIM

4 Corner Trim: 1x3, 74-1/2”L

4 Corner Trim: 1x3, 75-1/2”L

2 Door Side Trim: 1x3, 73-1/4”L

1Door Top Trim: 2x4, 66-1/2”L with angled ends (routed

edge)

2 Window Side Trim: 1x3, 26-5/8”L

1Window Top Trim: 2x4, 25”L with angled ends (routed

edge)

1 Window Bottom Trim: 1x4, 18-7/8”

4 Fascia: 1x4, 49-7/8”L

4 Gable Trim: 2x4, 55-7/8”L with angle cut (no heel cut)

page 6

TRIM CONTINUED

Quantity Description

4 Gable Bottom Corner Trim Block: 2x4, 6”L, with angle cut

MISCELLANEOUS PARTS

2 Doors with trim: 30” x 73”

1 Window: 18” x 23”

2 Vents: 4” x 16” aluminum

1 Threshold “Diamond” Plate: 59-3/8” with pre-drilled hole

HARDWARE

Suncast provides extra hardware for customer convenience. In

some cases, there will be extra small fasteners once the assembly

is complete.

65 2" Screws

30 2" inch Screws , black (with #2 square bit)

240 3" inch Screws

24 4" inch Screws

700 6d Galvanized Nails

1 lb. 2" inch Finish Nails

1 lb. 3" inch Finish Nails

1 lb. 3/4" Rooﬁng Nails

1 “L” Latch Outside door handlle

1 “D” Latch: Inside door handle

1 Top door latch: Barrel bolt

2 Cane latches

2 Door chain/spring

1 Caulk: 5.5 oz. tube

page 7

page 8

page 9

page 10

Inhaltsverzeichnis

Andere Suncast Außenlagerung Handbücher

Suncast

Suncast Brilliant by Design Stow-Away BMS4780 Bedienungsanleitung

Suncast

Suncast GLIDETOP BMS4900 Bedienungsanleitung

Suncast

Suncast HomePlace Vintage Garden Building Bedienungsanleitung

Suncast

Suncast Vista V7572PK Bedienungsanleitung

Suncast

Suncast Brilliant by Design Deck Box DB7000 Bedienungsanleitung

Suncast

Suncast BMS5700 Bedienungsanleitung

Suncast

Suncast GS8000 Bedienungsanleitung

Suncast

Suncast BMDB134004 Bedienungsanleitung

Suncast

Suncast Everett BMS6510 Bedienungsanleitung

Suncast

Suncast BMS6583 Bedienungsanleitung

Suncast

Suncast Brilliant by Design BMS9000 Series Bedienungsanleitung

Suncast

Suncast BMS7700 Bedienungsanleitung

Suncast

Suncast GLIDETOP BMS4950 Series Bedienungsanleitung

Suncast

Suncast BMS5700 Bedienungsanleitung

Suncast

Suncast DBW9936 Bedienungsanleitung

Suncast

Suncast BMS8125 Bedienungsanleitung

Suncast

Suncast BMS4700 Bedienungsanleitung

Suncast

Suncast DB5025P Bedienungsanleitung

Suncast

Suncast BMDB200 Bedienungsanleitung

Suncast

Suncast DB6300 Bedienungsanleitung

Suncast

Suncast Everett BMS6312 Bedienungsanleitung

Suncast

Suncast BMS4700X Bedienungsanleitung

Suncast

Suncast GS1000 Bedienungsanleitung

Suncast

Suncast DB9500 Bedienungsanleitung

Beliebte Außenlagerung Handbücher anderer Marken

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Bedienungsanleitung

TYGO

TYGO Nyland Bedienungsanleitung

Duratuf

Duratuf GL105 Bedienungsanleitung

Viking

Viking SD5300SS Technisches Handbuch

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Bedienungsanleitung

ModuLaro

ModuLaro Lojo WC202200 Bedienungsanleitung

Lifetime

Lifetime 6418 Bedienungsanleitung

rollaway container

rollaway container ARPCA24 Bedienungsanleitung

Duratuf

Duratuf Havelock Bedienungsanleitung

X-METAL

X-METAL 4065 Bedienungsanleitung

Outdoor Life Products

Outdoor Life Products FP2030 F Bedienungsanleitung

Royalcraft

Royalcraft Faro 295L Storage Box Bedienungsanleitung

Riverlea

Riverlea Duratuf KIWI KS3 Bedienungsanleitung

Rubbermaid

Rubbermaid 5L45 Bedienungsanleitung

garofalo

garofalo TUSCANY EVO Bedienungsanleitung

OLT

OLT GS84D-FJ-Plywood Bedienungsanleitung

Duratuf

Duratuf Kiwi MK1 Bedienungsanleitung

Eden

Eden CA2988 Bedienungsanleitung