Duratuf TUF 200 Bedienungsanleitung

Quality –Made Affordable

ASSEMBLY INSTRUCTIONS

TUF 200

BASE SIZE 1980mm x 855mm

Tools Required:

Before you start:

Safety:

Select your site:

 Drill

 Drill Bit 3.5mm

 Drill Bit 6mm (for clear roof panel only)

 Riveter

 Hammer

 Nail Punch

 Tape Measure

 Ladder or Saw stool

 String Line

 Masonry Drill and 10mm Masonry Bit (for Bolt Down Kit only)

 Read all instructions carefully.

 Identify all parts and check quantities against checklist.

 If you are making your own floor refer to Raised Base Plate section now.

 Do not attempt to build your shed in high winds.

 Beware of sharp edges.

 Protect your eyes and ears.

 Use electric tools with care. Use a Safety Trip Switch.

 It is easier and quicker if this shed is erected by two people.

 Your shed must be level. Achieve this by either levelling the ground or by using blocks.

 If you shed is to be positioned on wet or damp ground, we recommend that your shed is raised up

off the ground slightly.

ASSEMBLY INSTRUCTIONS

QTY LENGTH

CHECKED OUT CHECKED IN

2 1.890

1 1.890

1 1.070

2 1.070

2 1.980 Front & Back

2 .855 Ends

1 1.980 Back

1 1.980 Front

2 .855 Ends

4 1.810 Studs

2 1.833 Studs

2 0.765 45 x 45 H1

1 0.106 45 x 45 H1

1 0.823 45 x 45 H1

1 1.890 45 x 45 H1

SECURITY

2 Latches

COLOUR:__________________ INV #:_____________

TUF 200 PARTS LIST

ROOF SIZE: 2.010 x 1.070

- Blue 45 x 45 H1

Folded Roof Sheets

Roof Sheet Or

- Yellow 45 x 45 H1

Door

- Green 45 x 45 H4

DESCRIPTION

Clear Roof Panel

BASE PLATES

- Red 70 x 45 H1

Corner Wall Sheets

3/4 Front Wall Sheet (D008)

2 Pan Corner Wall Sheets

TIMBER

Wall Sheets

PACKED BY:

DATE: / /

BASE SIZE: 1.980 x 0.855

TOP PLATES

2.010

Touch-up Paint & Brush

- Red 45 x 45 H1

Door Jambs

FLASHINGS

Front Left Nog

Back Wall Nog

- Red 45 x 45 H1

Front Right Nog

Clear Panel Hardware Pack

End Wall Nogs

1.890

2.000

Hardware Pack

Top Plate Flashing

Assembly Instructions

Roof Flashing

Note: For sheds being positioned on a Purpose Built Floor, shorten Studs

by 30mm now (Refer to Floor Section).

Step 1: Select one End Base Plate 0.855m (Green), one End Top Plate

0.855m (Red) and two Studs (Yellow). Lay out on flat surface and nail

together using two 75mm nails per join (fig. 1). Repeat with the other

end frame.

Step 2: Select Back and Front Base Plates 1.980m (Green), Back Top Plate

1.980m (Red) and Front Top Plate (70x45mm). With one End Frame

lying on the ground, nail plates to frame, two 75mm nails per join.

Ensure Green joins to Green and Red joins to Red. See (fig. 2) for

nailing detail on Top Front Plate (70x45mm).

Step 3: Position remaining End Frame on top of plates. While someone sup-

ports frame, nail in place using two 75mm nails per join.

Step 4: Carefully roll frame over onto its base. Nail on Back and End Wall

Nogs .882m above the top of the Bottom Plate. If fitting a Duratuf

Floor, fit Floor Joists now. Evenly space joists and nail in place using

three 75mm nails per end. Nail Front wall Studs (Blue) using Front

Wall Nogs to get correct position, Nail remaining Front Wall Nogs in

centrally (this may be easier if the frame is rolled onto its Front wall).

Step 5: Fit front Top Plate Flashing centrally on Front Top Plate using four

30mm Clouts. Position Flashing so that the widest lip is on top.

TUF 200 TIMBER FRAME

fig. 1 fig. 2

YELLOW

1.810

BLUE

YELLOW

BLUE

Top Plate

Flashing

TUF 200 WALL CLADDING

fig. 1 fig. 2

To Avoid Corrosion:

Where at all possible try not to trap metal filings between two sheets. Remove all metal filings before riveting.

Carbon in pencils reacts with the Zinc/Aluminium coating on steel. Use ink to mark steel.

Step 1: Door Jambs: Position left hand Door Jamb Flashing at

correct measurement from left (cladding detail) and nail

to Top Plate using a 30mm clout. Do not fit 50mm nails at

this stage. Pre-drill holes to make nailing easier (fig. 1).

Position Door Jamb Flashing and nail at the bottom. Posi-

tion right hand Door Jamb Flashing 903mm from left

hand Door Jamb Flashing (cladding detail) and nail in

place.

FRONT VIEW

DOOR JAMB

FLASHING

903mm

180mm

D008

CLADDING DETAIL

Birds Eye View

TUF 200 WALL CLADDING

Birds Eye View

D008

= Rivet = 30mm Clout

Step 2: NOTE: It is very important that the Wall

Sheets are positioned exactly as shown in

the cladding detail diagram on the previous

page.

Position Corner Wall Sheets. Check that the

Lip is on the correct side of the sheet. While

holding Corner Wall Sheet flush with the top

of the Top Plate, nail to plate using only one

30mm clout top and bottom.

Step 3: Select Wall Sheet marked D008. Position at

right hand side of doorway. Rivet to Corner

Wall Sheet, one rivet top and bottom. Posi-

tion and rivet in place all remaining Wall

Sheets ensuring they overlap correctly.

While holding Front Wall Sheets up against

Top Plate Flashing, nail to top and bottom

plates using 30mm clouts.

Step 5: Drill a hole through Door Jamb Flashings

and Wall Sheets top and bottom. Nail with

50mm nails (fig. 1).

Nail left hand Door Jamb Flashing to Stud

using three 30mm Clouts at equal spacings

(fig. 1). Beside each 30mm Clout, rivet

Door Jamb Flashing to Rib. Repeat with

right hand Door Jamb Flashing.

Step 4: Nail Wall Sheets to Plates, two 30mm Clouts per pan top and bottom.

Nail Wall Sheets to Wall Nogs, one clout per pan.

TUF 200 ROOF

fig. 1

Step 1: Note: Condensation can form on the under side of shed roof. If building paper is required, fit now. Build-

ing paper will need to be supported by netting or roofing twine.

Standard Roof: Position Roof Sheets as shown in fig 1. Make sure sheet joins at the back are flush. Rivet

sheet joins, one rivet 300mm back from edge front and back.

Roof with Clear Panel: Handle Clear Panel with care. The Clear Panel will crack if not fitted correctly

Riveting: Pre-drill 3.3mm hole through Clear Panel and steel.

Nailing: Pre-drill a 6mm hole through Clear Panel. Hammer in nails with caution.

Position Roof Sheets as shown in fig.1. When fitting Clear Panel ensure it OVERLAPS Roof Sheets. Rivet sheet

joins, one rivet 300mm from edge front and back. When riveting Clear Panel to Roof Sheets use sealed rivet with

steel washer (fig. 2).

fig. 2

Step 3: Line up ribs on the roof with ribs on the

walls. While someone holds the Front Plate

straight, nail the roof to Top Plate using

one 40mm Weatherseal nail beside each

rib. Repeat at the back.

Step 2: Position Roof so that the front overhang

measures 150mm. Rivet roof to wall sheets

using one rivet every second Rib. Repeat at

the other end ensuring overhang measures

Step 4: Fit Roof Flashing as shown. When posi-

tioned correctly rivet through Roof Flashing

into Roof Sheet joins.

Sealed Rivet

Steel Washer

Clear Roof Panel

Steel

TUF 200 DOOR

Step 1: Place shed in final position. Check diagonal

measurements are equal and shed is level

before fitting door.

Step 2:

Hold Door in position (approximately 5mm down from Top

Plate Flashing) and fit one rivet to top hinge. While still

holding in position fit one rivet to bottom hinge.

Step 3:

Close door and check it fits correctly. If not, drill out

rivets and make necessary adjustments. Fit remaining

rivets to all three hinges.

Step 4: Using rivets attach padbolt as shown.

NOTE: If shed has an optional security upgrade, please use Security door instructions on next page.

Step 4: Slide the latch on to the handle shaft. Enter shed,

close door and adjust latch so it is snug with the stud

at the side of the door. Tighten up bolt on latch.

Note: Repeat Step 4 for second door handle if double security doors.

FORTRESS SECURITY DOOR (Optional)

Step 1: Place shed in final position. Check diagonal meas-

urements are equal and shed is level before fitting

door.

Step 2: Hold Door in

position (approximately

5mm down from Top

Plate Flashing) and fit

one rivet to top hinge.

While still holding in

position fit one rivet to

bottom hinge.

Step 3: Close door and check it fits correctly. If

not, drill out rivets and make necessary adjust-

ments. Fit remaining rivets to all three hinges.

TUF 200 FLOOR (Optional)

PURPOSE BUILT FLOOR

Step 1: Select the two Floor Boards which have

checked out corners. Position at front and

back of the shed so they fit around Studs.

For sheds being placed on a purpose built floor, we

recommend that the studs are shortened by 30mm.

The Wall Sheets will then protrude 20mm below the

Base Plate. This will stop water flowing in between

the Base Plate and Floor.

If you choose this option, the Floor should be made

15mm smaller than Base Size.

Note: Although it is not essential, fitting Damp

Proof Course in between the Base Plate and

the Floor will give added protection against

moisture.

i.e. CONCRETE / PLYWOOD

Step 2: Lay out remaining Floor Boards. Nail in

each Floor Board, two 50mm nails each

end and two into each Floor Joist.

Andere Duratuf Außenlagerung Handbücher

Duratuf

Duratuf TUF 400 Bedienungsanleitung

Duratuf

Duratuf PL44 Bedienungsanleitung

Duratuf

Duratuf KAIPARA Bedienungsanleitung

Duratuf

Duratuf MK4B Bedienungsanleitung

Duratuf

Duratuf SENTRY SS2007 Bedienungsanleitung

Duratuf

Duratuf Kiwi MK1 Bedienungsanleitung

Duratuf

Duratuf Smart store SS1507 Bedienungsanleitung

Duratuf

Duratuf SG3020 Bedienungsanleitung

Duratuf

Duratuf SL1520 Bedienungsanleitung

Duratuf

Duratuf SL3015 Bedienungsanleitung

Duratuf

Duratuf GL75 Bedienungsanleitung

Duratuf

Duratuf PG99 Bedienungsanleitung

Duratuf

Duratuf PS42 Bedienungsanleitung

Duratuf

Duratuf Garrison Sheds PL64 Bedienungsanleitung

Duratuf

Duratuf GS62 Bedienungsanleitung

Duratuf

Duratuf GL95 Bedienungsanleitung

Duratuf

Duratuf PL46 Bedienungsanleitung

Duratuf

Duratuf TUF 800 Bedienungsanleitung

Duratuf

Duratuf MK4 Bedienungsanleitung

Duratuf

Duratuf Paihia Bedienungsanleitung

Duratuf

Duratuf SG2520 Bedienungsanleitung

Duratuf

Duratuf MATAKANA Bedienungsanleitung

Duratuf

Duratuf PG88 Bedienungsanleitung

Duratuf

Duratuf MK4A Bedienungsanleitung

Beliebte Außenlagerung Handbücher anderer Marken

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Bedienungsanleitung

TYGO

TYGO Nyland Bedienungsanleitung

Viking

Viking SD5300SS Technisches Handbuch

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Bedienungsanleitung

ModuLaro

ModuLaro Lojo WC202200 Bedienungsanleitung

Lifetime

Lifetime 6418 Bedienungsanleitung

rollaway container

rollaway container ARPCA24 Bedienungsanleitung

X-METAL

X-METAL 4065 Bedienungsanleitung

Outdoor Life Products

Outdoor Life Products FP2030 F Bedienungsanleitung

Royalcraft

Royalcraft Faro 295L Storage Box Bedienungsanleitung

Riverlea

Riverlea Duratuf KIWI KS3 Bedienungsanleitung

Rubbermaid

Rubbermaid 5L45 Bedienungsanleitung

garofalo

garofalo TUSCANY EVO Bedienungsanleitung

OLT

OLT GS84D-FJ-Plywood Bedienungsanleitung

Eden

Eden CA2988 Bedienungsanleitung

Palram

Palram CANOPIA RUBICON 6x10 Administratorhandbuch

Suncast

Suncast 774098 Bedienungsanleitung

Lifetime

Lifetime 60186 Bedienungsanleitung