E-FLITE Gypsy Bedienungsanleitung
Assembly Manual
2
Table of Contents
Introduction ................................................................2
Table of Contents ........................................................2
Warning ....................................................................3
Additional Required Equipment ..................................3
Additional Tools and Adhesives ..................................3
Contents of Kit/Parts Layout ........................................4
Warranty Information ................................................5
Before Starting Assembly ............................................6
Using the Manual ......................................................6
Checking the Wing Washout ......................................7
Attach the Wing ........................................................8
Join the Vertical Fin and Horizontal Stabilizer ..............9
Attach the Tail to the Fuselage ..................................12
Radio Installation ......................................................14
Linkage Installation ..................................................18
Landing Gear Installation ..........................................22
Motor Break-in ........................................................25
Motor Installation ......................................................25
Battery Installation ....................................................28
Control Throws ........................................................29
Center of Gravity ......................................................31
Range Test Your Radio ..............................................32
2004 Official AMA
National Model Aircraft Safety Code ........................34
Introduction
The Gypsy EP ARF Park Flyer is a nostalgic old timer,
perfect for leisure and sport flyers who want relaxing
flights. The Gypsy offers a great flying experience with
excellent climb performance, high wing stability,
quality balsa and plywood construction, and quality
UltraCote®covered with an eye catching appeal.
Specifications
Wingspan: 35.25 in (895 mm)
Length: 27.5 in (698.5 mm)
Wing Area: 266 sq in (17.16 sq dm)
Weight w/o Battery: 13.5–14.5 oz (382–411g)
3
AdditionalTools and Adhesives
Tools
Square Side cutters
Hobby knife Heat gun
Ruler Small pliers
Phillips screwdriver Hex wrench: 3/32"
Felt-tipped pen
Drill bit: 1/16" (1.5mm), 1/8" (3mm)
Adhesives
Medium CA
Other
Heat gun
Motor/Gearbox
370-size with 5.33:1 gearbox (included)
Propeller (10x4.7) (included)
20mm diameter w/gearbox brushless (optional)
Warning
An RC aircraft is not a toy! If misused, it can cause
serious bodily harm and damage to property. Fly only
in open areas, preferably at AMA (Academy of Model
Aeronautics) approved flying sites, following all
instructions included with your radio.
Additional Required Equipment
Recommended JR® Systems
Servos: JR 241 Sub-micro servo (2)
Receiver: JR R610M 6-channel micro FM Rx
Battery and Speed Control Requirements
Li-Po Battery: 7.4V 1900 2-Cell
7-cell Ni-MH 730mAh battery
Speed Control: 10 amp (EFLA104)
4
Contents of Kit/Parts Layout
Replacement Parts:
Main Wing EFL2051
Fuselage EFL2052
Tail Assembly EFL2053
Windshield EFL2057
Battery Hatch EFL2058
Items not shown:
Pushrod Set EFL2054
Main Landing Gear EFL2055
Wheel Set EFL2056
Decal Set EFL2059
Micro Control Horns EFLA200
Micro Pushrod Keepers EFLA201
Tailskid EFLA202
Micro Control Connectors EFLA203
370 Motor w/5.33:1 gearbox EFLM205
Micro Rubber Spinner EFLA204
10x4.7 Slow Flyer Propeller EFLP1047
Double-sided tape/Hinge Tape EFL2060
5
Optional Parts
Park 370 Brushless Motor, 4100Kv EFLM1000
10x7 Slow Flyer Propeller (2) EFLP1070
11x4.7 Slow Flyer Propeller (2) EFLP1147
11x7 Slow Flyer Propeller (2) EFLP1170
12x3.8 Slow Flyer Propeller (2) EFLP1238
12x6 Slow Flyer Propeller (2) EFLP1260
Celectra 1-2 cell Li-Po Charger EFLC3000
Celectra 1-3 cell Li-Po Charger EFLC3005
Before Starting Assembly
Before beginning the assembly of your Gypsy, remove
each part from its bag for inspection. Closely inspect
the fuselage, wing panels, rudder and stabilizer for
damage. If you find any damaged or missing parts,
contact the place of purchase.
Using the Manual
This manual is divided into sections to help make
assembly easier to understand, and to provide breaks
between each major section.
Remember to take your time and follow the directions.
6
Please note that once assembly of the model has
been started, you must contact Horizon Hobby, Inc.
directly regarding any warranty question. Please do
not contact your local hobby shop regarding warranty
issues, even if that is where you purchased it. This
will enable Horizon to better answer your questions
and service you in the event that you may need
any assistance.
If the buyer is not prepared to accept the liability
associated with the use of this product, the buyer is
advised to return this kit immediately in new and
unused condition to the place of purchase.
Horizon Hobby, Inc.
4105 Fieldstone Road
Champaign, Illinois 61822
(877) 504-0233
www.horizonhobby.com
Warranty Information
Horizon Hobby, Inc. guarantees this kit to be free from
defects in both material and workmanship at the date
of purchase. This warranty does not cover any
component parts damage by use or modification. In no
case shall Horizon Hobby’s liability exceed the original
cost of the purchased kit. Further, Horizon Hobby
reserves the right to change or modify this warranty
without notice.
In that Horizon Hobby has no control over the final
assembly or material used for the final assembly, no
liability shall be assumed nor accepted for any
damage resulting from the use of the final assembled
product. By the act of using the assembled product, the
user accepts all resulting liability.
7
Checking theWingWashout
Required Parts
Wing
Required Tools and Adhesives
Heat gun
❍1. Place the wing on a flat surface and check the
wing washout. There must be 1/2" (13mm)
between the trailing edge of the wing at the tip
and work surface when the center of the wing
is flat against the work surface. If the wing is
not twisted correctly, hold the wing in a twisted
position and use a heat gun to remove the
wrinkles from the covering. Repeat the process
until the correct washout is present. The
washout makes the plane more stable in flight.
8
❍2. Secure the wing to the fuselage using a 4-40 x
1/2" socket head bolt and a #4 flat washer.
Note: The 4-40 socket head screw uses the
3/32" hex wrench.
Attach theWing
Required Parts
Wing
Required Tools and Adhesives
Heat gun
Hex wrench: 3/32"
❍1. Place the wing onto the fuselage by guiding
the wing dowel into the hole on the
forward former.
Join theVertical Fin and Horizontal
Stabilizer
Required Parts
Vertical fin
Horizontal stabilizer
Required Tools and Adhesives
Medium CA
Square
Felt-tipped pen
Hobby knife
❍1. Draw two lines on the top of the stabilizer
extending back from the sides of the notch in
the front to the trailing edge. Use a square to
make the lines 90-degrees to the trailing edge
of the stabilizer.
Note: The hole for the control horn will be on the
left side when the top is facing up.
9
❍2. Carefully remove the covering along the lines
using a sharp hobby knife. Be very careful not
to cut into the underlying wood and weaken
the stabilizer. If the stabilizer is weakened, it
could fail in flight.
❍3. Align a straight edge along the bottom of the
fin. Use a felt-tipped pen to draw a line onto
the lower front section of the fin. Draw lines on
both sides of the fin.
10
Inhaltsverzeichnis
Andere E-FLITE Spielzeug Handbücher
E-FLITE
E-FLITE Carbon-Z Cub SS Bedienungsanleitung
E-FLITE
E-FLITE Blade CP Bedienungsanleitung
E-FLITE
E-FLITE J-3 Cub 25 ARF Bedienungsanleitung
E-FLITE
E-FLITE Power 25 BL Bedienungsanleitung
E-FLITE
E-FLITE Pitts Model 12 15e ARF Bedienungsanleitung
E-FLITE
E-FLITE Extra 300 32e Bedienungsanleitung
E-FLITE
E-FLITE UMX Spacewalker Bedienungsanleitung
E-FLITE
E-FLITE Extra 330SC BP Bedienungsanleitung
E-FLITE
E-FLITE UMX PittsS-1S Bedienungsanleitung
E-FLITE
E-FLITE Hurricane 25e TM Bedienungsanleitung
E-FLITE
E-FLITE EFLH3000 Bedienungsanleitung
E-FLITE
E-FLITE Beast 60e Bedienungsanleitung
E-FLITE
E-FLITE UMX Vapor Lite HP BNF Basic Bedienungsanleitung
E-FLITE
E-FLITE F86 Sabre 15DF Bedienungsanleitung
E-FLITE
E-FLITE Carbon-Z Splendor Bedienungsanleitung
E-FLITE
E-FLITE Super Cub 25e ARF Bedienungsanleitung
E-FLITE
E-FLITE T-34 Mentor 25e ARF Bedienungsanleitung
E-FLITE
E-FLITE UMX AS3Xtra Bedienungsanleitung
E-FLITE
E-FLITE hawker sea fury 400 arf Bedienungsanleitung
E-FLITE
E-FLITE Blade 400 3D Bedienungsanleitung
