e-survey E600 Bedienungsanleitung
E600 User Manual
E600 GNSS Receiver
User Manual
V1.0_201910
E600 User Manual
Contents
1. Introduction ..........................................................................................................3
1.1 Appearance...................................................................................................3
1.2 Indicator........................................................................................................3
1.3 Interface........................................................................................................4
1.4 Pin definition.................................................................................................5
1.5 Power button................................................................................................5
2. Web User Interface...............................................................................................6
2.1 Position .........................................................................................................6
2.2 Satellites........................................................................................................6
2.3 Information...................................................................................................7
2.4 Working Mode ..............................................................................................7
2.5 Satellite Setting.............................................................................................7
2.6 Device Configuration.....................................................................................8
2.7 NMEA Message.............................................................................................8
2.8 View Logs ......................................................................................................9
2.9 Raw Data.......................................................................................................9
2.10 Backup Data ..................................................................................................9
2.11 Management...............................................................................................10
3. Basic Operation...................................................................................................10
3.1 Insert SIM and TF card ................................................................................10
3.2 Insert and remove battery..........................................................................10
3.3 Charge the battery......................................................................................11
3.4 Insert radio antenna ...................................................................................11
3.5 Measure antenna height.............................................................................11
3.6 E-bubble Calibration ...................................................................................12
4. Internal Radio......................................................................................................13
4.1 Default channel frequency..........................................................................13
4.2 Supported radio protocol ...........................................................................13
5. Standard Accessories..........................................................................................14
6. Technical Specifications......................................................................................15
7. Warranty Policy...................................................................................................16
E600 User Manual
1. Introduction
This is the user manual for survey E600H/E600N/E600T GNSS receiver. It gives basic
description and operation guide which may help user to operate device properly.
1.1 Appearance
The E600 main body is designed with magnesium alloy material to provide durable
usage and better heat dispersion as well as light weight 1.3Kg (dual batteries inside).
The dual battery slot design makes it possible to replace battery without interrupting
the working.
1.2 Indicator
Working status is viewable through the indicators. The meaning of each indicator:
Indicator
Color
Meaning
Satellite
Red and Green
•Off: no receiving satellites
•Flash red: receiving satellites but no
solution status
•Flash green: have solution but not fixed
•Solid green: fixed solution
•Flash red and green alternately: mainboard
abnormal
Data link
Green and Blue
•Solid green: datalink is ready to start
•Flash green: datalink is transmitting data
normally
E600 User Manual
•Flash Blue: when raw data recording is
enabled, the LED will flash according to the
interval
Battery
Green and Red
•Solid green: battery level between
30%~100%
•Flash green: battery level between
10%~30%
•Flash red: battery level below 10%
Bluetooth
Blue
•Off: no Bluetooth connection
•Solid blue: has Bluetooth connection
1.3 Interface
E600 GNSS receive bottom interface is shown as below. There are two battery slots.
Micro SIM card and TF card can be installed from slot A. The 7-pin port can be
connected to 7-pin cable for data downloading and NMEA output. 5-pin port is used
to connect external radio and external power. The TNC port is for internal radio.
7-pin port
5-pin port
UHF port
Speaker
Battery slot A
Battery slot B
Battery slot A
TF card
Micro SIM card
Battery cover lock
Battery cover lock
E600 User Manual
1.4 Pin definition
The 5-pin and 7-pin ports are defined as below:
5 Pin
Front View
1
+12V
Power
2
GND
Power ground
3
TXD
Device out
4
SGD
Signal ground
5
RXD
Device in
7 Pin
Front View
1
--
Reserved
2
USB_DN (-)
3
USB_VBUS
4
USB_DP (+)
5
TXD
Device out
6
RXD
Device in
7
SGD
Signal ground
1.5 Power button
There is a power button on E600 control panel, the main function as below:
Power On
Long press button for two seconds to power on
receiver.
Power Off
Long press button for two seconds then release,
will hear the voice “Power off?” Then press the
button again to confirm.
Broadcast Current Working
Mode
Receiver will broadcast current working mode
when press the power button.
Self-check
Long press button for two seconds then release,
will hear the voice “Power off?” Then long press
button for three seconds, will hear the voice “self-
check”.
7-pin Port
5-pin Port
UHF Port (TNC)
Port front view
E600 User Manual
2. Web User Interface
User can connect to receiver WIFI hotspot with PC, smart phone or tablet. The hotspot
name is the device serial number, can be found under the bottom of the device label.
Open web browser and input the IP address “192.168.10.1”. The default user name is
“admin”, password is “password”. From the website, user can manage working status,
change working mode, configurate basic settings, download raw data, update
firmware and register device.
2.1Position
View basic position information, satellite number, PDOP and time. In static mode, can
start and stop recording here.
2.2Satellites
View satellite list and satellite map, set cut-off angle.
E600 User Manual
2.3Information
View receiver information: firmware version, GNSS board, radio and network module.
2.4Working Mode
Configurate working mode: base, rover or static.
2.5Satellite Setting
Configurate the satellites to be used. “RTK Timeout” setting is for aRTK service (With
Hemisphere L-Band service, user cans still keep high accuracy for a period when
correction data loses). “Surefix” is hemisphere technology to increase the reliability
of the fixed solution. Which means it will be much more difficult to get fixed solution
in tough environment.
E600 User Manual
2.6Device Configuration
Configurate receiver settings: User can set time zone. Direct link mode is used for
debug. Sensor means e-bubble data output. Also, the 7-pin port baud rate is
changeable. Smart voice broadcast can be disabled. When TF card is insert, can select
static data prior storage. When external power is connected,can also choose to power
on receiver automatically. When network is enabled, the network module will be
activated even in radio working mode. This is helpful for fast initializing the network
module, but also increase the power consumption. When SIM card is insert and “WIFI
share network” is enabled, PC can surf the internet when connected to device hotspot
by using SIM data. “Cloud service” and “Track back” is used for uploading position
information to cloud/TCP server.
2.7NMEA Message
Configurate NMEA data output through Bluetooth or 7-pin port.
E600 User Manual
2.8View Logs
The log files can be used to diagnose issues. Click “download” to download the files.
2.9Raw Data
Download raw data or convert data to RINEX format. User can use check box, then
click “Package” to download multiple files.
2.10 Backup Data
The points collected in SurPad4.0 will be backup in receiver storage automatically to
avoid data loss. Can restore the data to SurPad software.
E600 User Manual
2.11 Management
User can update receiver and GNSS firmware as well as register device, format
internal disk, restore factory setting, restart device. To update the firmware, click
“Chose File” to import the firmware, then click “Upload File” to start updating.
3. Basic Operation
This part shows user some basic operations to start working with E600.
3.1Insert SIM and TF card
E600 supports external TF card expansion up to 32 GB for static data storage. Micro
SIM card can be used for network working mode. Open battery cover “A”and insert
TF card or SIM card.
3.2 Insert and remove battery
Insert battery and slide as the arrow in below picture to lock it. Then, lock the battery
cover. It is suggested to remove battery if the receiver is not in use for a long time.
Inhaltsverzeichnis
Andere e-survey Empfänger Handbücher
e-survey
e-survey CORS System Net 20 Plus Bedienungsanleitung
e-survey
e-survey E200 Bedienungsanleitung
e-survey
e-survey E600H Bedienungsanleitung
e-survey
e-survey E500 Bedienungsanleitung
e-survey
e-survey E800 Bedienungsanleitung
e-survey
e-survey E100 Bedienungsanleitung
e-survey
e-survey E200 Bedienungsanleitung
e-survey
e-survey E100 Bedienungsanleitung
e-survey
e-survey E500 Bedienungsanleitung
e-survey
e-survey CORS System Net 20 Plus Bedienungsanleitung
