Earth Way 2170T Bedienungsanleitung

(Qty 4 #36214)

1/4-20 X 1½”

Phillips Panhead

(Qty 4 #36300)

1/4-20 SS Locknut

36210

Qty 2

36214

Qty 4 31100

Qty 7 31120

Qty 2

*31114

Qty 1

32103

Qty 9

31106

Qty 3

32100

Qty 2

33117

Qty 1

36105

Qty 1

33108

Qty 1

33109

Qty 1

36300

Qty 6

12152

Qty 2

12148

Qty 2

*Included in Extension Kit

12 9

44249

1. Remove and identify all loose parts from carton.

2. Position hopper on side. Install frame using (4) 1/4-20 x 1½” Pan Head Phillips

machine screws and (4) 1/4-20 nylon insert locknuts. First put bolts through holes in

frame then through the holes in bottom of hopper. Secure with locknuts. TIGHTEN

THESE LOCKNUTS NOW......TIP: coat stainless steel bolts with wax or grease

before tightening to prevent them from seizing.

DO NOT TIGHTEN WITH POWER TOOLS.

7-2013 Pt# 52165 PAGE 1

2170T CommerCial Tow

BroadCasT spreader

ASSEMBLY and OPERATING INSTRUCTIONS

PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS

REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT

SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, EMAIL: TECHSUPPORT@EARTHWAY.COM

HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY

;If your spreader does not spread evenly, be sure the word “FRONT” on the gear box points toward the tow bar of the

spreader. The impeller must turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise.

Clean the impeller surface after each use. Fertilizer stuck on the impeller blades will cause uneven spreading.

;Your spreader is designed to be pulled at three miles per hour, which is a brisk walking speed. Slower or faster speeds will

change the spread patterns. Wet fertilizer will also change the spread pattern and ow rate. Clean and dry your spreader

thoroughly after each use. Coat all metal surfaces (inside & outside of chassis) with light oil or silicon spray to help

prevent corrosion. Wash between the shut-off plate and bottom of the hopper.

;Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.

OVER

3 MPH

Do not tow

faster than

3 MPH

ROCK SALT and POWDERED MATERIALS

should not be used in this spreader as it will damage

the gearbox and can void the warranty.

Use only granular materials.

IF YOUR SPREADER COMES SEMI ASSEMBLED, SKIP TO STEP #7

MADE IN THE USA

FRONT

44249

Gearbox &

Axle Assembly

Drive wheel

side

Coast wheel

side

Frame brace

1/4-20 x 1½”

Hex Head Bolt

Step 6B & 6C

1/4-20 x 2¼”

Hex Head Bolt

Step 6A

1/4-20 Locknut

Impeller

Cross Brace

Numbers

Frame

Lower Handle

Pivot Rod

Shut-Off

1/4-20 x 1½”

Pan Head Bolt

3. Install impeller onto pinion shaft. Insert 1/8”x 1¼” cotter pin through

impeller then through pinion shaft. Use hole closest to the gear box. Spread

cotter pin to prevent from falling out. Next, insert the Cross Brace into the

Gearbox Brace.

Pinion

Shaft

⅛ x 1¼”

Cotter Pin (#36105)

DRIVE WHEEL

HOLE

COAST WHEEL

HOLE

Impeller

Cross Brace

Gearbox & Axle Assembly

Gearbox Brace

Front

4. Install gear box by inserting the pinion shaft into hole in center of

hoppers bottom. The word “FRONT” on the gearbox must point to

Front of the hopper. Follow label instructions on hopper.

Axle Bearing

Flat

Side

Notch

5. Install axle bearings to both lower

handles. NOTE: Notch on bearings and

lower handles. Bearings must go through

at side of lower handle.

6. A - Install lower handles onto axle

to both sides as shown. Insert 2¼” bolt

through second hole in lower handle and

through rst hole in frame install locknut.

DO NOT TIGHTEN.

B - Now insert 1½” bolt through rst hole in lower handle. Then through frame brace. NOTE: Numbers on frame brace must be facing

toward gear box as shown. Next into threaded connector in cross brace. DO NOT TIGHTEN.

C - Next insert 1½” bolt through other end of frame brace and through second hole in frame install the second cross brace - this one has a

cross hole in the center of the tube.

PAGE 2

NOW GO BACK AND TIGHTEN ALL NUTS AND BOLTS STARTING WITH FIRST STEP. DO NOT OVER TIGHTEN.

Gearbox &

Axle Assembly

Lower

Handle

Frame

Brace

Cross Brace

Axle Bushing

11. Slide axle bushing over axle and into axle bearing to both sides as shown.

12. Install drive wheel to axle using pin hole nearest to lower handles as shown.

Insert 2” cotter pin through wheel and through axle. Bend with pliers to prevent pin

from falling out.

13. Install coast wheel to axle using outside pin hole. As shown, insert 1” cotter pin

through axle (not thru the wheel). Bend with pliers to prevent pin from falling

out.

TURN SPREADER UPRIGHT ON TO WHEELS. PAGE 3

7. Insert pivot rod into shut off plate as shown. Turn to lock in place.

8. Insert other end of pivot rod into pivot and bracket assembly as shown. Turn to lock in place.

9. Install Control Support between lower handles as shown inserting (2) 2” bolts thru the Pivot Bracket and the Lower Handles and secure

with (2) lock nuts. Next, line up the hole in the Cross Brace with the hole in the Control Support. Insert 1/4-20 X 2¼” bolt through the

Control Support and thru the hole in the Cross Brace, secure with a 1/4-20 lock nut. Now determine if you want to add the Hitch Extension

to the Control Support. If you do add the Extension, use the 1/4-20 x 1½” bolt & lock nut through the Hitch Extension tube and the Control

Support as shown above. And use the 1/4-20 X 1¾” bolt to install the Hitch Plates and secure with a 1/4-20 lock nut. If not used, secure the

Hitch Plates by using 1/4-20 x 1½” bolt and 1/4-20 lock nut through the Control Support and the Hitch Plate as shown above.

10. Attach Gauge & Lever assembly to Control Support using (2) 1/4-20 X 1½” bolts and (2) 1/4-20 lock nuts and TighTen.

1/4 X 2¼”

Hex Head Bolt

1/4 - 20

Lock Nut

1/4 - 20

Lock Nut

1/4 - 20

Lock Nut

1/4 X 1½”

Hex Head Bolt

Hitch Plates

Hitch Extension

Mounting

1/4 X 1½”

Hex Head Bolt

1/4 - 20

Lock Nut

1/4 X 1¾”

Hex Head Bolt

1/4 X 2”

Hex Head Bolt

Shut-Off

Plate

Pivot Rod

with extra bend

Rotate

Pivot

2” Cotter Pin

Drive Wheel

1” Cotter Pin

Coast Wheel

GAUGE & LEVER

ASSEMBLY

Control Rod

Tabbed Hole

Control Rod

Lever Tensioning Nut

Gauge Setting

Overlay

14. Install (1) 1/4-20 regular nut (not a locknut)

on to control rod as shown.

15. Install attened end of control rod in to lever on gauge as shown. Turn to lock in

place. Next push lever forward to setting “0”. Align control rod with hole in pivot

bracket, pull lever backward to insert control rod through hole in pivot bracket. Now

install 1/4-20 regular nut on to control rod.

16. Pull lever back to setting “30” as shown. Next push pivot & bracket forward

so that the shut off plate in the hopper is in the full open position. REMEMBER

SETTING “30” ON THE FLOW CONTROL LEVER MUST PLACE THE

SHUT-OFF PLATE IN THE FULL OPEN POSITION TO BE PROPERLY

CALIBRATED. Now tighten the nuts against the pivot bracket to prevent change in

calibration.

17. Tension on the ow control lever may be adjusted by tightening or loosening the

tension nut as shown.

¼-20

Hex Nuts

Pivot

Bracket Control

Rod

Pivot

Rod

18. Insert agitator to pinion shaft on inside of hopper.

Note: the position of at side of the agitator. This pin

should be installed as shown.

PAGE 4

1/4-20 x 1”

Hex Head Bolt

Stainless

1/4-20 Lock Nut

Stainless

19. Install debris screen into hopper, then insert 1/4-20 x 1”

Stainless Steel Hex Bolt thru the hole in the side wall of the

hopper. Secure with Stainless Steel lock nut - TIGHTEN

WITH HAND TOOLS ONLY

PAGE 5

The settings furnished on the Rate Setting Matrix are intended as a guide only. Variations in physical characteristics of

material applied, towing speed, and roughness of ground surface may require slightly different spreader settings. Due to the

above conditions, the manufacturer makes no warranty as to the uniformity of coverage actually obtained from the settings

listed.

5-YEAR LIMITED WARRANTY

Earthway Products, Inc. warrants this product free of defects in original workmanship and materials for a period of 5-Years to the end user

with the original purchase receipt. If a manufacturing non-conformance is found, Earthway Products, Inc. at its discretion will repair or

replace the part(s) or product at no charge provided the failure is not the result of incorrect installation, mishandling, misuse, tampering,

or normal wear and tear as determined by Earthway. Earthway at its discretion may require that the part(s) or product be returned along

with the original purchase receipt at owners’ expense for examination and compliance with the terms of this warranty. Do not return any

product without rst receiving authorization from Earthway Products, Inc. To seek remedy under this warranty, contact Earthway Products,

Inc. at 574-848-7491, techsupport@earthway.com or write to Earthway Products, Inc. P.O. Box 547 Bristol, Indiana 46507 and describe

the nature of the manufacturing defect. SPECIFIC LIMITATIONS: This warranty covers only the part(s) or product; any labor charges

associated with repair or replacement of non-conformances are specically excluded. Due to the corrosive nature of most fertilizers and ice

melt products, Earthway Products, Inc. makes no warranty against and specically excludes part(s) or product degradation or failure due to

corrosion or its effects. Clean and dry your spreader thoroughly after each use, as a preventative measure, coat all metal parts (inside and

outside of the steel tubing) with a light oil or silicon spray.

HOW TO ORDER SPARE PARTS

All spare parts listed herein may be ordered direct from the

manufacturer. Be sure to give the following information when

ordering.

;Model Number

;Part Number

;Part Description

Call (574) 848-7491, 800-294-0671, or order online at

www.earthway.com/parts

OPERATING INSTRUCTIONS

Before lling hopper, become familiar with the operation of this

spreader.

1. Obtain proper setting for material to be used from the RATE

SETTING CHART included with this spreader.

2. Move stop bolt on rate gauge assembly to the proper setting.

3. While pushing spreader forward, pull control lever back to

stop bolt.

4. To stop, push lever forward to close ow holes before you stop

moving.

5. When nished, empty any remaining material from hopper.

6. Thoroughly wash spreader and allow to dry before storing.

Light oiling can prevent corrosion.

Full Rate Path Half Rate Path

Start

Finish

Start

Finish

44249

16 15

228

77002

OPTIONAL

Heavy-Duty Rain Cover

60060R

OPTIONAL

Heavy-Duty

Rain Cover

Side Deflector Kit

2170T Broadcast Tow Spreader ~ Parts List

Key # Part # Description Key # Part # Description

1 70138 PNEUMATIC DRIVE WHEEL STUD 22 42263 CONTROL ROD

2 33109 3/16" X 2" COTTER PIN ZINC 23 31138 #8 X 3/8" PMT #8 HD COARSE BLACK

3 33117 AGITATOR 24 36208 #6 X 3/8" TYPE 25 PHPS S.S.

4 33108 3/16" X 1" COTTER PIN ZINC 25 32100 1/4-20 HEX NUT ZINC

5 12317 SHUT OFF PLATE 26 12148 AXLE BEARING

6 44251 PIVOT ROD 27 12152 AXLE BUSHING

7 60300 PIVOT & BRACKET ASSEMBLY 28 60309 GEAR BOX & AXLE ASSEMBLY

8 31120 1/4-20 X 2" HHCS ZINC 29 19113 1.0" OD HOLE PLUG BLACK

9 25207 LOWER HANDLE 30 44215 HITCH PLATE (PULL)

10 22601 UPPER CROSS BRACE 31 40003 SQUARE SCREEN

11 32103 1/4-20 NYLON INS LOCKNUT ZINC 32 60335 HOPPER ASSEMBLY

12 25108 FRAME 33 12209 HOPPER BUSHING

13 25603 CONTROL SUPPORT 34 36214 1/4-20 X 1 1/2" PHPMS S.S.

14 25228 CROSS BRACE 11.25” 35 36300 1/4-20 NYLON INSERT LOCKNUT S.S.

15 44249 FRAME BRACE (2150/2170) 36 36210 1/4-20 X 1" HHMS S.S.

16 31100 1/4-20 X 1 1/2 HHMS ZINC 37 77051 HITCH EXTENSION KIT includes (1 each) #41, 11, and 25703

17 31106 1/4-20 X 2 1/4" HHCS ZINC 38 60027 WING NUT ASSEMBLY BLACK

18 12109 IMPELLER (9" DIA) 39 37100 1/4-20 X 1" CARRIAGE BOLT ZINC

19 36105 1/8" X 1 1/4" COTTER PIN S.S. 40 12147 SPACER (PIVOT LINK)

20 11927 SHUTOFF SUPPORT- LARGE 41 31114 1/4-20 X 1 3/4" HHCS ZINC

21 60298 GAUGE & LEVER ASSEMBLY

Earthway Products, Inc.

P.O. Box 547

Bristol, IN 46507

Phone: 800-294-0671

www.earthway.com

You can nd replacement nuts & bolts at your local hardware store.

60166R

OPTIONAL

3-Side Salt

Deflector Kit

Standard Settings Gauge Overlay #12196 and

OPTIONAL Lesco Settings Gauge Overlay #12195

Bolt Identifier

1-1/2”

1-3/4”

1”

2”

2-1/4”

Inhaltsverzeichnis

Andere Earth Way Streuer Handbücher

Earth Way

Earth Way 2170 Bedienungsanleitung

Earth Way

Earth Way EV-N-SPRED M30 Bedienungsanleitung

Earth Way

Earth Way 2050TP Bedienungsanleitung

Earth Way

Earth Way 2130 High-Output Bedienungsanleitung

Earth Way

Earth Way Ev-N-Spred 2050 Bedienungsanleitung

Earth Way

Earth Way Hand Crank Spreader Betriebsanleitung

Earth Way

Earth Way POLAR TECH 90365 Bedienungsanleitung

Earth Way

Earth Way FLEX-SELECT F80PSD Bedienungsanleitung

Earth Way

Earth Way EV-N-SPRED M20 Bedienungsanleitung

Earth Way

Earth Way 2130 Bedienungsanleitung

Earth Way

Earth Way EV-N-SPRED 2150 Bedienungsanleitung

Earth Way

Earth Way M30 Bedienungsanleitung

Earth Way

Earth Way 2050TP Bedienungsanleitung

Earth Way

Earth Way EV-N-SPRED Bedienungsanleitung

Earth Way

Earth Way M80 Bedienungsanleitung

Earth Way

Earth Way 2100P Estate Bedienungsanleitung

Earth Way

Earth Way PolarTech 90399 Montageanleitung

Earth Way

Earth Way EV-N-SPRED C22HD Bedienungsanleitung

Earth Way

Earth Way EV-N-SPRED C24HD Bedienungsanleitung

Earth Way

Earth Way Ev-N-SprEd 2030 Series Bedienungsanleitung

Earth Way

Earth Way 2170 Bedienungsanleitung

Earth Way

Earth Way 2030 Bedienungsanleitung

Earth Way

Earth Way Ev-N-Spred M24SSD Series Bedienungsanleitung

Earth Way

Earth Way EV-N-SPRED C24HD Bedienungsanleitung

Beliebte Streuer Handbücher anderer Marken

PEQUEA

PEQUEA GT-100 Bedienungsanleitung

Herculano

Herculano H2RS9 Bedienungsanleitung

Epoke

Epoke SKE8 Bedienungsanleitung

GEA

GEA EL44 Technisches Datenblatt

Boss Snowplow

Boss Snowplow TGS 800 Bedienungsanleitung

Fisher

Fisher EMERSON 168 Series Bedienungsanleitung

Fisher

Fisher POLY-CASTER 78601 Bedienungsanleitung

TurfEx

TurfEx RS7200 Betriebsanleitung

Ferris

Ferris Pathfinder Series Bedienungsanleitung

Fayat Group

Fayat Group DYNAPAC S100 Fehlerbehebungshandbuch

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Installations- und Betriebshandbuch

EASTMAN

EASTMAN CR 500 Bedienungsanleitung

Nogueira

Nogueira RoyalFlow-600 Bedienungsanleitung

Buyers

Buyers TGS05B Bedienungsanleitung

Magnum

Magnum V-BOX PV Series Beilage

Meyer's

Meyer's VB280 Bedienungsanleitung

SnowEx

SnowEx VX-4210 Bedienungsanleitung

Kramer

Kramer VM-400HDCP Bedienungsanleitung