Eaton ESWA4500C Bedienungsanleitung

ESWA4500C Multi-Source Volume Control Module

Installation Manual

Control functions [1] [2] [3]

System ON - The EATON A-BUS system will activate if any function button is pressed.

Input Selection [1] - The system will restart on the last source selected. One of the four input

LEDs [5] will indicate which input has been selected. The input can be changed by pressing

left or right buttons [1].

Volume Level [2] - If the system has been switched off the Volume Control will restart at low

volume level. If the system has remained active the Volume Control will return to the

previously selected volume level. The level may be adjusted by pressing the Up/Down

buttons [2]. While the level is being adjusted, the input LEDs [5] will ripple left or right.

Remote Control [4] - The Volume Control may be operated by remote control. The IR remote

must have clear line-of-site to the IR Receiver. The Volume Control can also relay IR remote

control commands to the hub and connected source components. It will repeat standard 38

kHz commands and 56 kHz commands which are often used in satellite receivers. You may

experience difficulty with some remote control commands on some components. The

operating range can be affected by sunlight and some lighting systems.

Off and All Off [3] - A Volume Control can be switched off individually by pressing the off

button, this will turn off the backlighting to the volume control [2] and input selection buttons

[1]. The backlighting of the off [3] and input indicator will [5] remain on. If there are other

Volume Control’s connected to the same zone their status will not be affected. If the off button

[3] is pressed for more than three seconds the whole A-BUS system will turn off. When the

system is off the infrared relay system will remain active.

Backlight adjustment [6] - The backlighting level of the function buttons [1] [2] [3] can be

adjusted to individual requirements.

This Keypad Volume Control Module has been

designed to work with intelligent EATON A-BUS

Multi-Source Hubs using standard A-BUS commands.

It will operate with other single source and multi-source

hubs, however, some functionality such as source

selection maybe not be available.

These functions can be accessed with a remote control

handset containing the correct codes.

Note: For comprehensive instructions please also refer

to the instructions supplied with your EATON A-BUS

multi-source hub.

A-BUS is a registered trademark of LeisureTech Electronics Pty Ltd.

All features and specifications are subject to change without notice.

All trademarks property of their respective owners.

Installation

It is recommended that your EATON Volume Control is installed by a qualified installer to ensure

that the installation is carried out correctly and it complies with all relevant installation regula-

tions. The Volume Control should not be installed next to or in the same box as high voltage

devices. The Volume Control is connected to the hub via a single category 5 cable, it is recom-

mended that it should not be run parallel or close to high voltage cables or data cables, etc.

The EATON Volume Control is designed to fit into a single Gang bracket. The category 5 cable

from the hub should be properly connected to either the 110 punchdown [7], using a proper

installation tool. It is recommended that the category 5 cable length be no longer than 100ft.

(30M), longer runs may induce noise and reduce sound quality. The speaker cable terminal [8]

will accept up to 14 gauge cable.

Set-up [9] - The A-BUS installation should be completed with all power modules connected but

not installed into the walls. Follow these steps to give you maximum control flexibility over the

volume of your A-BUS system. On the back of the power modules there are trim pots (Left &

Right) [9] that fine-tune the output level to compensate for the length of the cable run, the

efficiency of the speakers and the size of the room. There are also situations where you may

want to limit the output level in a particular room. With the trim pots adjusted to minimum, the

main volume control should be adjusted to maximum level, then with popular music playing the

trim pots should be brought up to a point just below the amplifier’s clipping level. (Clipping is the

point where the sound starts to distort). When the trim pots are all set to the desired level the

installation may be completed.

Mini Remote Control Handset ESWA100CR

The mini remote control handset supplied contains basic A-BUS remote control commands,

volume Up/Down [10] up to 4 individual input selections [11] Off [12] andAll Off (Global) [13]. In

good conditions this handset should have an operating range of up to 70ft. (20M), in poor

conditions such as bright sunlight it maybe less than 15ft. (5M).

42mm

BACKESWA100CR REMOTE CONTROL

SUPPLIED

PUNCHDOWN VERSION SHOWN

FRONT

70.25mm

106mm

42.75mm

71mm

L- L+

R+ R-

SPEAKER OUT

BR BRW BL BLW GR GRW OR ORW

LEVEL ADJUST

L CH R CH

ESWA100CR

Inhaltsverzeichnis

Andere Eaton Controller Handbücher

Eaton

Eaton CSAU-01 Handbuch

Eaton

Eaton CEAG CG-Controller Bedienungsanleitung

Eaton

Eaton SVX9000 Series Bedienungsanleitung

Eaton

Eaton Cutler-Hammer S801TR Bedienungsanleitung

Eaton

Eaton SC100 Bedienungsanleitung

Eaton

Eaton Cutler-Hammer FD100 Bedienungsanleitung

Eaton

Eaton xComfort CSAU-01/03 Bedienungsanleitung

Eaton

Eaton Freedom 2100 Handbuch

Eaton

Eaton ELC-CODNET Bedienungsanleitung

Eaton

Eaton S811+N37 series Bedienungsanleitung

Eaton

Eaton DILM12-XPBC Handbuch

Eaton

Eaton C441 Series Bedienungsanleitung

Eaton

Eaton xComfort Bridge Stücklistenhandbuch

Eaton

Eaton ELCM Series Bedienungsanleitung

Eaton

Eaton CGLine+ Bedienungs- und Wartungsanleitung

Eaton

Eaton ATC-600 Programmierhandbuch

Eaton

Eaton xComfort CJAU-01 Series Bedienungsanleitung

Eaton

Eaton WaveLinx series Bedienungsanleitung

Eaton

Eaton SVCH0203 SPX Advanced Gebrauchsanweisung

Eaton

Eaton ELC Series Bedienungsanleitung

Eaton

Eaton ELC-PC12NNDR Bedienungsanleitung

Eaton

Eaton Cutler-Hammer ATC-300 Bedienungsanleitung

Eaton

Eaton Ampgard 400 Bedienungsanleitung

Eaton

Eaton XC-CPU101 Series Handbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch