Eaton 9E10000i Bedienungsanleitung

Page 1

powerquality.eaton.com

Eaton 9E

6-20kVA

Page 2

Contents

1. INTRODUCTION 3

1.1 SAFETY INSTRUCTION 3

1.2 CERTIFICATION STANDARDS 4

1.3 SPECIAL SYMBOLS 4

2.PRESENTATION 5

2.1 MODEL LIST 5

2.2 ELECTRICAL STRUCTURE 5

2.2 UPS VIEWS 6

3.INSTALLATION 9

3.1 UNPACKING 9

3.2 PACKAGE CONTENT 9

3.3 CONNECTION 10

4.OPERATION 16

4.1DISPLAY AND BUTTONS 16

4.2 OPERATING UPS 18

4.3 CONFIGURATION 19

4.4 TROUBLE SHOOTING 20

4.5 ALARM CODES 21

5.TECHNICAL DATA 22

Page 3

1. Introduction

1.1 Safety instruction

•The UPS must be installed and maintained exclusively by quailified staff. See installation and operation

instructions before connecting to the supply.

•The UPS must be installed with an earth connection. It has a high leakage current. The first wire to be

connected is the earth wire, which must be connected to the terminal marked PE (yellow/green).

•The UPS generates a leakage current of over 3.5 mA. The leakage current of the load should be added to that

of the UPS on the protective earth wire.

•The UPS needs a neutral connection to work properly. Operation without Neutral may damage the unit.

•A readily accessible disconnect device shall be incorporated in the building installation wiring for permanently

connected equipment.

•The UPS generates hazardous electric voltages inside it even when the input and/or battery switches are

open. The inside of the UPS is protected by safety guards that are not to be removed by non-qualified staff. All

installation and maintenance or other operations that entail gaining access to the inside of the UPS require the

use of tools and are to be performed exclusively by qualified staff.

•The UPS contains an energy source: the batteries. All terminals and sockets may be powered even when the

UPS is not connected to the mains.

•The total battery voltage is potentially hazardous: it may cause an electric shock. The compartment containing

the batteries is protected by safety guards, which are not to be removed by non-qualified staff. All battery

installation and maintenance operations entail gaining access to the inside of the UPS and require the use of

tools: these operations are to be performed exclusively by qualified staff.

•The batteries replaced are to be considered as toxic waste and treated accordingly. Dispose of used batteries

according to the instructions. Do not throw the batteries into fire: they could explode. Do not attempt to open

the battery casing: no maintenance work can be done on them. In addition, the electrolyte is hazardous for the

skin and eyes and may be toxic.

•Risk of explosion if battery is replaced by an incorrect type.

•Do not turn on the UPS if you see any leaks of liquid or a white powder residue.

•Make sure that no water, liquid in general and/or other foreign matter gets inside the UPS.

•Under hazardous conditions, turn off the UPS at the “1/0” main power switch and open all the isolators present

(see the user manual to locate the “1/0” main power switch and the isolators).

•Do not open the battery fuse holders while the UPS is powering the load from the batteries. An interruption of

the battery DC voltage may cause an electric arc and result in breakage of the equipment and/or fire.

•The energy required to power the load is provided by the batteries in the event of a power failure. if the battery

protection were open, the load would be powered off.

•Fuses have to be replaced with the same type if necessary.

•To connect external battery cabinets, use the expansion cable suggested by the manufacturer in this manual.

Page 4

1.2 Certification Standards

1.3 Special Symbols

The following are examples of symbols used on the UPS or accessories to show you the important information:

Safety

IEC 62040-1:2008

IEC 60950-1:2005 (Modified)

EMC

Conducted Emission: IEC 62040-2. Category C3

Radiated Emission: IEC 62040-2. Category C3

ESD:IEC 61000-4-2. Contact: Level 2, Air discharge: Level 3

RS:IEC 61000-4-3. Level 3

EFT:IEC/EN 61000-4-4. Level 4

Surge:IEC/EN 61000-4-5. Level 4

CS:IEC/EN 61000-4-6. Level 3

MS:IEC/EN 61000-4-8. Level 3

Voltage Dips, short interruptions and voltage variations:IEC/EN 61000-4-11

Warning: This is a product for commercial and industrial application, in other environment

installation restrictions or additional measures may be needed to prevent disturbances. Additional

curbs may be needed while output wiring length is more than 10m or communication wiring length

is more than 3m.

Page 5

2.Presentation

9E series UPS uses ON-LINE double conversion technology, resulting in the highest levels of reliability and maximum

protection for critical loads.

2.1 Model List

Model

Power Ratings

Voltage (Output)

9E6Ki

6kVA/4.8kW

0.8

230V (220/240)

9E10Ki

10kVA/8kW Combo

0.8

230V (220/240)

9E10KiXL

10kVA/8kW Combo

0.8

230V (220/240)

9E15Ki

15kVA/12kW Combo

0.8

230V (220/240)

9E20Ki

20kVA/16kW Combo

0.8

230V (220/240)

9E20KiXL

20kVA/16kW Combo

0.8

230V (220/240)

9EEBM180

For 9E6Ki

180V

9EEBM240

For 9E10Ki, 9E10KiXL

240V

“XL” Model: Model with internal supercharger, and without internal batteries. Other models with internal

batteries

2.2 Electrical structure

9E6Ki

INPUT

OUTPUT

Input

filter AC/DC—DC/AC Output

filter

Internal

power

Charger

Battery

Input

Switch

Bypass

Maintain Switch

Output

Switch

Main power wiring

9E10Ki, 9E10KiXL

INPUT

OUTPUT

Input

filter AC/DC—DC/AC Output

filter

Internal

power

Charger

Battery

Input

Switch

Bypass

Maintain Switch

Output

Switch

Main power wiring

9E15Ki, 9E20Ki, 9E20KiXL

Page 6

INPUT

OUTPUT

Input

filter AC-DC DC-AC Output

filter

Internal

power Charger

Battery

Input

Switch

Bypass

Maintain Switch

Output

Switch

Main power wiring

2.2 UPS views

2.2.1 UPS FRONT VIEW

①

Display

②

Multipurpose buttons

③

Wheels (front wheels swivel and can be locked, fixed rear wheels)

Page 7

2.2.2 UPS REAR VIEW

9E6Ki

With backpanel cover

9E6Ki

Without backpanel cover

9E10Ki/9E10KiXL

With backpanel cover

9E10Ki/9E10KiXL

Without backpanel cover

④

USB communication port

⑩

Input switch

⑤

RS232 communication port and contacts

⑪

Cover for terminals

⑥

Slot for optional communication card

⑫

Fuse

⑦

Cooling fan(s)

⑬

Terminals for I/O cable connection

(refer to related

section)

⑧

Output switch

⑭

Earthing screws

⑨

Manual bypass for maintenance

⑮

Tie wrap hold-down

Page 8

UPS REAR VIEW

9E15Ki/9E15KiXL/9E20Ki/9E20KiXL

With backpanel cover

9E15Ki/9E15KiXL/9E20Ki/9E20KiXL

Without backpanel cover

④

RS232 communication port and contacts

⑩

Input switch

⑤

USB communication port

⑪

Cover for terminals

⑥

Slot for optional communication card

⑫

Terminals for I/O cable connection (refer to related section)

⑦

Cooling fans

⑬

Earthing screws

⑧

Output switch

⑭

Fuse

⑨

Manual bypass for maintenance

⑮

Tie wrap hold-down

2.2.3 EBM REAR VIEW

①

Fuse

②

Cover for terminals

③

Tie wrap hold-down

④

Wheels (front wheels swivel and can be locked, fixed rear

wheels)

⑤

Terminals for I/O cable connection (refer to related section)

⑥

Earthing screws

Page 9

3.Installation

3.1 Unpacking

1. Cut the straps and carefully remove the cardboard

box by sliding it upwards.

2. Remove the accessory box, the wooden slide and the

top polystyrene foam corner pieces.

3. Remove the bottom polyethylene corner pieces by

rotating them as shown in the figure.

4. Open the protective bag and pull it all the way down.

5. Put the previously removed slide on the back part of the

pallet (see figure). Make sure that the slide rests firmly

against the pallet so it remains in place during unloading

operations. Pull the UPS from the front with caution when

sliding it off the pallet.

NOTE: All parts of the packaging should be kept for future

use.

3.2 Package content

After opening the packaging, it is first necessary to check the contents.

The package must contain:

UPS USB cable RS232 cable

Jumper

(15/20kVA models only)

User manual Software CD

Page 10

3.3 Connection

3.3.1INSTALLATION REQUIREMENTS

Warning:

Installation must be performed by qualified personnel. The first connection to perform is the protective conductor (earth

cable), which must be connected to the screw marketed .

The UPS, when inserted in an installation, does not alter the existing neutral (system earthing) arrangements.

A differential switch upstream will also be triggered for a fault occurring downstream of the UPS. In calculating reactivity of this

switch, account must be taken of the leakage current of the UPS (approx. 8 mA) plus that of the load which come together on the

UPS’s earth conductor.

UPS input Differential switch

Single-phase Type B or Type A

Three-phase Type B

The neutral arrangements are altered only if there is an isolating transformer or when the UPS operates with a neutral that is

disconnected upstream.

In any case avoid connecting the output neutral with the input neutral or to the earth as this could damage the UPS.

Reminder : The UPS needs a neutral connection to work properly. Operation without Neutral may damage the unit.

For installation with change in system earthing arrangement or galvanic isolation see below schematic

Fig.3-1 Change in SEA or Galvanic isolation

Notice: It is required to install an external isolating device against current backfeed between Mains input and UPS. After the device

is installed, it must add a warning label with the following wording or the equivalent on the external AC contactor: RISK OF

VOLTAGE BACKFEED. Isolate the UPS before operating on this circuit, then check for hazardous voltage between all terminals.

The current rating of T - AC contactor should be more than 1.3 times of UPS capacity

Fig.3-2 Typical external isolating device installation

Single phase input Three phase input

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Eaton UPS Handbücher

Eaton

Eaton 5E 500 Bedienungsanleitung

Eaton

Eaton PowerRite XT PRXT-0400A Bedienungsanleitung

Eaton

Eaton 9PX2000RT-L Montageanleitung

Eaton

Eaton 5E Montageanleitung

Eaton

Eaton Ellipse ECO 500 Montageanleitung

Eaton

Eaton DIN500AC Montageanleitung

Eaton

Eaton 5S 700VA Bedienungsanleitung

Eaton

Eaton 5P 1550G RL Bedienungsanleitung

Eaton

Eaton Protection Station 650 Bedienungsanleitung

Eaton

Eaton Powerware 5125 Bedienungsanleitung

Eaton

Eaton 9395-275 Handbuch

Eaton

Eaton Nova AVR 500 Bedienungsanleitung

Eaton

Eaton 93PM IBC-L Bedienungsanleitung

Eaton

Eaton Powerware 9170+ Bedienungsanleitung

Eaton

Eaton Power Xpert 9395 550 Bedienungsanleitung

Eaton

Eaton Ellipse MAX 600 Bedienungsanleitung

Eaton

Eaton 91PS UPS 8-40 kW Handbuch

Eaton

Eaton 9PX1000IRT2U-L Montageanleitung

Eaton

Eaton EX 2200 RT 2U Bedienungsanleitung

Eaton

Eaton 9E Bedienungsanleitung

Eaton

Eaton Powerware 9355 Bedienungsanleitung

Eaton

Eaton 9EHD Series Bedienungsanleitung

Eaton

Eaton 9E20K-TH Bedienungsanleitung

Eaton

Eaton 5E Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung