Eaton MBP6Ki Bedienungsanleitung

ENGLISH

HotSwap MBP

Maintenance Bypass

MBP6Ki

MBP11Ki

MBP11Ki31

Installation

and user manual

Service and support:

Call your local service representative

SK-90510-Y4_EN

Page 2 SK-90510-Y4_EN

Special symbols

The following are examples of symbols used on the HotSwap MBP to alert you to important

information:

RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol.

Important instructions that must always be followed.

This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE)

in the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.

Information, advice, help.

Refer to the user manual of UPS.

SAVE THESE INSTRUCTIONS. This manual contains important instructions

that should be followed during installation and maintenance of the MBP and UPS.

The HotSwap MBP models that are covered in this manual are intended for installation in an environment

within 0 to 40°C, free of conductive contaminant.

This equipment has been tested and found to comply with Class A UPS,pursuant to Part 15 of the FCC

Rules.These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment.This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to correct the interference at his own

expense.

Certication standards (in use with UPS)

• Safety: IEC/EN 62040-1 / Ed.1: 2008.

• EMC: IEC 62040-2 / Ed.2: 2005

EN 62040-2 / Ed.2: 2006.

• Performance: IEC/EN 62040-3 / Ed.2.0: 2011.

• IEC 61000-4-2 (ESD): level 3.

• IEC61000-4-3(Radiatedeld):level3.

• IEC 61000-4-4 (EFT): level 4.

• IEC 61000-4-5 (Fast transients): level 4.

• IEC61000-4-6(Electromagneticeld):level3.

• IEC61000-4-8(Conductedmagneticeld):level4.

SAFETY INSTRUCTIONS

Page 3

SK-90510-Y4_EN

ENGLISH

Safety of persons

• The system has its own power source when connected to the UPS (UPS battery). Consequently,

the power outlets may be energized even if the system is disconnected from the AC power source.

Dangerous voltage levels are present within the system.

Itshouldbeopenedexclusivelybyqualiedservicepersonnel.

• Theproductmustbeproperlygrounded,alwaysconnecttheearthwirerst

Product safety

• The MBP connection instructions and operation described in the manual must be followed

in the indicated order. Disconnection and overcurrent protection devices shall be provided by others

for AC in/out circuits.

• CAUTION-Toreducetheriskofre,theunitconnectsonlytoacircuitprovidedwithbranchcircuit

overcurrent protection (please refer to the UPS User Manual for current rating).

The upstream circuit breaker must be easily accessible.

The unit can be disconnected from AC power source by opening this circuit breaker, and if still

connected to UPS, by previously shutting down the UPS (refer to the UPS User Manual)

• Check that the indications on the rating plate correspond to your AC powered system and to the

actual electrical consumption of all the equipment to be connected to the system.

• Never install the system near liquids or in an excessively damp environment.

• Never let a foreign body penetrate inside the system.

• Never expose the system to direct sunlight or source of heat.

• If the system must be stored prior to installation, storage must be in a dry place.

• The admissible storage temperature range is -15ºC to +60ºC.

Special precautions

• The HotSwap MBP is designed to work with approved EATON UPS (contact your Eaton reseller for

more information)

• All repairs and service should be performed by AUTHORIZED SERVICE PERSONNEL ONLY.

There are NO USER SERVICEABLE PARTS inside the MBP.

SAFETY INSTRUCTIONS

Page 4 SK-90510-Y4_EN

1. Introduction....................................................................................... 5

1.1 Environmental protection...................................................................................................5

2. Presentation ...................................................................................... 6

2.1 Standard positions .............................................................................................................6

2.2 Description / Panels...........................................................................................................8

3. Installation ........................................................................................ 9

3.1 Inspecting the equipment..................................................................................................9

3.2 Unpacking the MBP...........................................................................................................9

3.3 Checking the accessory kit................................................................................................9

3.4 Mechanical Mounting ...................................................................................................... 10

3.5 Installation requirements ................................................................................................. 10

4. Power cables connection ................................................................11

4.1 MBP6Ki............................................................................................................................ 11

4.2 MBP11Ki / MBP11ki31 – with common Normal and Bypass AC source ......................... 12

4.3 MBP11Ki / MBP11Ki31 – with separate Normal and Bypass AC source ......................... 13

5. Operations....................................................................................... 15

5.1 UPS start-up with HotSwap MBP.................................................................................... 15

5.2 UPS replacement with HotSwap MBP ............................................................................ 16

5.3 UPS maintenance with HotSwap MBP ...........................................................................18

6. Specications.................................................................................. 19

Contents

Page 5

SK-90510-Y4_EN

ENGLISH

1. Introduction

Thank you for selecting an EATON product to protect your electrical equipment.

The HotSwap MBP range has been designed with the utmost care.

We recommend that you take the time to read this manual to take full advantage of the many features

of your MBP (Maintenance Bypass).

BeforeinstallingyourHotSwapMBPwithyourUPS,pleasereadrstthesafetyinstructions.

Then follow the indications in this manual, which completes the UPS Installation and User Manual.

To discover the entire range of EATON products, we invite you to visit our web site at www.eaton.com/

powerquality or contact your EATON representative.

1.1 Environmental protection

EATON has implemented an environmental-protection policy.

Products are developed according to an eco-design approach.

Substances

This product does not contain CFCs, HCFCs or asbestos.

Packing

To improve waste treatment and facilitate recycling, separate the various packing components.

• The cardboard we use comprises over 50% of recycled cardboard.

• Sacks and bags are made of polyethylene.

• Packingmaterialsarerecyclableandbeartheappropriateidenticationsymbol 01

PET

Materials Abbreviations Number in 01

PET

the symbols

Polyethylene terephthalat PET 01

High-density polyethylene HDPE 02

Polyvinyl chloride PVC 03

Low-density polyethylene LDPE 04

Polypropylene PP 05

Polystyrene PS 06

Follow all local regulations for the disposal of packing materials.

End of life

EATON will process products at the end of their service life in compliance with local regulations. EATON

works with companies in charge of collecting and eliminating our products at the end of their service life.

Product

The product is made up of recyclable materials.

Dismantling and destruction must take place in compliance with all local regulations concerning waste.

At the end of its service life, the product must be transported to a processing center for electrical and

electronic waste.

Page 6 SK-90510-Y4_EN

2. Presentation

The Eaton® HotSwap MBP module makes it possible to service or even replace the UPS without affecting

the connected loads (HotSwap function).

You can safely eliminate the effects of UPS maintenance and guard the integrity of your equipment.

Providingoutstandingreliability,theEatonHotSwapMBPuniquebenetsinclude:

• Easy and fast connection to UPS due to Input/Output and signal "all in one" patented connector

(Hotswap MBP 5/6kVA range)

• "make before break" feature to allow full servicing (electrical power continuity) when switching from

UPS position to Bypass (and vice versa)

• Communication feature with UPS*: detection of MBP connection and switch position (Normal or Bypass)

(* works only with some approved EATON UPS - contact your Eaton reseller for more information)

• Load connection by both terminal blocks and IEC outlets (10A C13 and/or 16A C19 following MBP ver-

sions)

• Adjustable 19’’ Rack kit and multiple positionsTower installation kit provided

• Backed by worldwide agency approvals.

2.1 Standard positions

MBP6Ki

Tower installation

Rack installation Wall mounting

Page 7

SK-90510-Y4_EN

ENGLISH

2. Presentation

MBP11Ki / MBP11Ki31

Tower installation

Rack installation Wall mounting

Description Weight

(lb/kg)

Dimensions (inch/mm)

D x W x H

MBP6Ki 5.5 / 2.5 4.3 x 7.0 x 5.1 / 110 x 177 x 130

MBP11Ki 12.1 / 5.5 5.2 x 13.2 x 5.1 / 132 x 336 x 130

MBP11Ki31 12.1 / 5.5 5.2 x 13.2 x 5.1 / 132 x 336 x 130

Page 8 SK-90510-Y4_EN

2. Presentation

2.2 Description / Panels

The HotSwap MBP has a manual Bypass rotary switch with two positions:

• UPS the load is supplied by the UPS

• Bypass the load is supplied directly by the AC power source

On MBP11Ki and MBP11Ki31, it is possible to Bypass the load on a separate Bypass AC source

(see 4.3 for more details)

2 lights indicate the HotSwap MBP power status:

• "UPS supply" green light: when active, the UPS output is available, the Bypass switch can be safely

turned to UPS position

• "Bypass mode" red light: when active, indicates that the HotSwap MBP is on “Bypass mode” (Bypass

switch turned to Bypass position)

Normal AC source switch / Bypass AC source switch (following MBP versions):

Allow to safely switch off the AC source of the UPS, for UPS maintenance / replacing

MBP status detection:

A signal cable, with RJ11 connector to plug to the UPS, allows the communication to the UPS to manage

the MBP status, and the indication on UPS display panel of both following status:

• MBP connection to UPS

• Bypass switch position

Check the UPS user manual to check the compatibility of this feature, or contact Eaton reseller for more

information

MBP6Ki

MBP11Ki / MBP11Ki31

(1) Input/Output terminal blocks

(2) Normal AC source switch

(3) Input/Output/MBP-Detection

connector to the UPS

(4) Manual Bypass switch

(5) (2) 16A outlets

(6) (3) 10A outlets

(7) UPS supply green light

(8) "Bypass" mode red light

(1) Input/Output terminal blocks

(2) Input/Output cables for

connection to the UPS

(3) Bypass terminal blocks for

connection to the UPS

(4) Normal AC source switch

(5) Bypass AC source switch

(6) Signal cable for MBP detection to

the UPS

(7) Manual Bypass switch

(8) (4) 16A outlets

(9) UPS supply green light

(10) "Bypass" mode red light

5 34

1 26

8109 2 6

3 517

Page 9

SK-90510-Y4_EN

ENGLISH

3. Installation

3.1 Inspecting the equipment

If any equipment has been damaged during shipment, keep the shipping cartons and packing materials

forthecarrierorplaceofpurchaseandleaclaimforshippingdamage.Ifyoudiscoverdamageafter

acceptance,leaclaimforconcealeddamage.

Toleaclaimforshippingdamageorconcealeddamage:

1) File with the carrier within 15 days of receipt of the equipment;

2) Send a copy of the damage claim within 15 days to your service representative.

3.2 Unpacking the MBP

Unpack the equipment and remove all the packing materials and shipping carton.

Discard or recycle the packaging in a responsible manner, or store it for future use.

Placethecabinetinaprotectedareathathasadequateairowandisfreeofhumidity,ammablegas,

and corrosion.

Packing materials must be disposed of in compliance with all local regulations concerning waste.

Recycling symbols are printed on the packing materials to facilitate sorting.

3.3 Checking the accessory kit

• Verify that the following additional items are included with the MBP:

MBP6Ki

(1) Input/Output UPS cord Set

(2) Rack kit for 19-inch enclosures

(3) Fixation kit for Rack mounting

(including square nuts and

screws)

(4) Tower and Wall mounting kit

(including 2 ears and screws)

(5) Installation and User manual

MBP11Ki/ MBP11Ki31

(1) (2) cable glands for UPS Input

Bypass connection (option)

(2) Rack kit for 19-inch enclosures

(3) Fixation kit for Rack mounting

(including square nuts and

screws)

(4) Tower and Wall mounting kit

(including 2 ears and screws)

(5) Installation and User manual

Page 10 SK-90510-Y4_EN

3.4 Mechanical Mounting

• Mount the MBP (on the UPS, on the EBM, in the rack or on the wall), see 2.1.

3.5 Installation requirements

Recommended protective devices and cable cross-sections

1. Recommended upstream protection

Refer to the UPS User Manual for circuit breaker current rating.

The circuit breaker has to be installed upstream the MBP Normal AC source.

2. Recommended cable cross-sections

3. Installation

Terminal

position

Wire

function

Terminal wire

size rating

Minimum input wire

size rating

Tightening

torque

MBP6ki

L1 Phase

0.5-10 mm2

(20-8 AWG)

6 mm2(10 AWG) 105°C

10 mm2(8 AWG) 75°C

1 Nm

(10 lb in)

N (L2) Neutral

(Phase)

Ground

MBP11ki

L1 Phase

4-25 mm2

(12-4 AWG)

10 mm2(8 AWG) 105°C

16 mm2(6 AWG) 90°C

2 Nm

(18 lb in)

N (L2) Neutral

(Phase)

Ground

MBP11ki31

L1 Phase

4-25 mm2

(12-4 AWG)

10 mm2(8 AWG) 105°C

16 mm2(6 AWG) 90°C

2 Nm

(18 lb in)

L2 Phase

L3 Phase

N Neutral

Ground

Copper wire, solid or stranded.

Andere Handbücher für MBP6Ki

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Eaton UPS Handbücher

Eaton

Eaton 500 Bedienungsanleitung

Eaton

Eaton Ellipse MAX 600 Bedienungsanleitung

Eaton

Eaton Protection Station 650 Bedienungsanleitung

Eaton

Eaton Powerware 9125 Bedienungsanleitung

Eaton

Eaton Powerware 9390 Bedienungsanleitung

Eaton

Eaton 3S 550 Bedienungsanleitung

Eaton

Eaton 93PM IBC-LW Bedienungsanleitung

Eaton

Eaton 3C3-EX Series Bedienungsanleitung

Eaton

Eaton 93E 30ITC Bedienungsanleitung

Eaton

Eaton Powerware 3105 UPS Bedienungsanleitung

Eaton

Eaton 3SMini Bedienungsanleitung

Eaton

Eaton Power Xpert 9395P-1100/1100 Bedienungsanleitung

Eaton

Eaton 9910-E16 Bedienungsanleitung

Eaton

Eaton 93PM IBC-L Bedienungsanleitung

Eaton

Eaton 5SC 1500G Bedienungsanleitung

Eaton

Eaton Eaton 5PX Montageanleitung

Eaton

Eaton 93E Bedienungsanleitung

Eaton

Eaton 9E 10000i Bedienungsanleitung

Eaton

Eaton Ellipse ECO 500 Bedienungsanleitung

Eaton

Eaton CA22106060000R6 Bedienungsanleitung

Eaton

Eaton 9PXM Bedienungsanleitung

Eaton

Eaton Power Xpert 9395 Bedienungsanleitung

Eaton

Eaton Power Xpert 9395 Bedienungsanleitung

Eaton

Eaton 5S 1000VA Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung