Eaton Powerware 9125 Bedienungsanleitung
Powerware 9125 (9910-E64) UPS
Installation Guide for IBM Applications
®
®
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
RISK OF ELECTRIC SHOCK - Indicates that a risk of electric shock is present and the
associated warning should be observed.
CAUTION: REFER TO OPERATOR’S MANUAL - Refer to your operator’s manual for
additional information, such as important operating and maintenance
instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries
in the trash. This product contains sealed, lead-acid batteries and must be
disposed of properly. For more information, contact your local recycling/reuse or
hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic
equipment (WEEE) in the trash. For proper disposal, contact your local
recycling/reuse or hazardous waste center.
IBM, pSeries, AIX, xSeries, AS/400, OS/400, and RS/6000 are registered trademarks and iSeries, OpenPower, and
i5/OS are trademarks of International Business Machines Corp.
Eaton, Powerware, X-Slot, LanSafe are registered trademarks and ConnectUPS is a trademark of Eaton Corporation
or its subsidiaries and affiliates.
Burndy is a registered trademark of Framatone Connectors International.
ECopyright 2007 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Eaton Corporation.
EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1 i
Table of Contents
1 Installation 1.........................................................
Parts List 1..........................................................................
Setup and Installation 4.................................................................
Tools Required 4....................................................................
Rack-Mount Setup 5.................................................................
Installing the Internal Batteries 12........................................................
Tower Setup 13.....................................................................
EBM Installation 17.....................................................................
PDM Installation 18.....................................................................
PDM Rear Panels 20....................................................................
UPS Installation 21.....................................................................
Remote Emergency Power-off Installation 22...................................................
Power Connections and Startup 23..........................................................
Typical Power Connections 28..............................................................
2 Operation 37..........................................................
Turning the UPS On 37...................................................................
Starting the UPS on Battery 37.............................................................
Turning the UPS Off 38...................................................................
Initiating the Battery Test 38...............................................................
Transferring the UPS to Bypass Mode 39......................................................
Operating Modes 39....................................................................
Normal Mode 40....................................................................
Battery Mode 41....................................................................
Bypass Mode 42.....................................................................
Standby Mode 42....................................................................
3 Communication Options 43..............................................
i5, iSeries, or AS/400 and Serial Server Interface Overview 44.......................................
Serial (TTY) Interface Overview 47...........................................................
p5 or pSeries with Logical Partitions Interface Overview 48.........................................
4 Service and Support 49.................................................
TABLE OF CONTENTS
EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1
ii
This page intentionally left blank.
EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1 1
Chapter 1 Installation
Parts List
IBM part numbers are subject to change without notice.
Table 1. E64 Base Configuration (42R8073)
Quantity IBM MN IBM FC IBM PN Eaton®PN Description
1
11
E64 –42R8073 103003635-3992 UPS 6000 VA, 4200W (in shipping carton or factory-installed in
rack)*
11
103006314 (1) Left Rail Assembly*
103006315 (1) Right Rail Assembly*
157606083-003 (2) Mounting Brackets*
180500167-203 (4) Mounting Bracket Screws (#6-32×3/8”)*
1 – – 42R8074 103003946-3992 E64 Accessory Kit
2 – – 42R4316 103003217-3991 Battery Trays
* If the UPS is factory-installed in an IBM rack, these items are pre-assembled.
Table 2. E64 Application Matrix
IBM
MN
IBM
FC
IBM
PN Eaton PN Description
i5/
iSeriest
Tower
IEC
i5/
iSeries
Tower
NEMA
p5/
pSeries®
Tower
IEC
p5/
pSeries
Tower
NEMA
p5/
pSeries
Rack
WW
i5/
iSeries
Rack
WW
–6571 42R4318 103003918-3991 NEMA
PowerPass®
Distribution
Module (PDM)
– 1 – 1 – –
–6572 42R4319 103003919-3991 IEC PDM 1 – 1 – – –
–2939* 42R4332 103004741-5591 Relay-Serial
Card and Cable
Kit (DB-9,
1.8m/6 ft; DB-25,
9.1m/30 ft)
1 1 – – – 1
* Maximum: One FC 2934 or 2939 per E64 UPS.
NOTE IEC: IEC Countries (e.g., UK, Italy, etc.); NEMA: NEMA Countries (e.g. U.S. and Canada); WW: Worldwide
INSTALLATION
EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1
2
Table 3. E64 Options Matrix
IBM
MN
IBM
FC
IBM
PN
Eaton
PN Description
i5/
iSeries
Tower
IEC
i5/
iSeries
Tower
NEMA
p5/
pSeries
Tower
IEC
p5/
pSeries
Tower
NEMA
p5/
pSeries
Rack
WW
i5/
iSeries
Rack
WW
–2934* 39J4824 116750221-001 ConnectUPSt-X
Web/SNMP Card
– – Min: 0, Max: 1 –
–6645 42R8075 103003387-3992 Extended Battery
Module (EBM)
Min: 0, Max: 4
– – 42R8076 103003947-3992 EBM Accessory
Kit
1 per FC 6645
* Maximum: One FC 2934 or 2939 per E64 UPS.
NOTE IEC: IEC Countries (e.g., UK, Italy, etc.); NEMA: NEMA Countries (e.g. U.S. and Canada); WW: Worldwide
Table 4. E64 Accessory Kit (42R8074)
Quantity Eaton PN Description
1164201513 Powerware 9125 Two-in-One UPS (5000/6000 VA) User’s Guide
1164201697 Powerware 9125 (9910-E64) Installation Guide for IBM Applications
1103004870 Software Suite CD
1157604790-002 UPS Lower Front Cover
1116750226-001 Serial Cable (RJ-45 to DB-9, 1.8m/6 ft)
1124102044-001 Serial Cable (DB-9 to DB-9, 1.8m/6 ft)
1157606088-001 Battery Retaining Bracket
2180500222-022 Battery Retaining Bracket Screws (M4×10 mm)
405147635-3 Pedestals
4180500136-202 Pedestal Mounting Screws (M4×8 mm)
1103002843-3992 Rail Hardware Kit (metric):
S(8) M5×12 Pan-Head Screws
S(8) M5×10 Flat-Head Screws
S(4) M5×16 Hex-Head Screws
S(4) M5 Clip Nuts
S(2) Square-Hole Adapter Plates
INSTALLATION
EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1 3
Table 5. E64 6645 EBM Components (42R8075)
Quantity IBM MN IBM FC IBM PN Eaton PN Description
1 — 6645 42R8075 103003387-3992 E64 6645 EBM 3U High (in shipping carton or
factory-installed in rack)*
103006308 Accessory Kit*:
S(1) EBM Front Cover (157604790-002)
S(1) Left Rail Assembly (103006173)
S(1) Right Rail Assembly (103006172)
1 — — 42R8076 103003947-3992 EBM Accessory Kit
* If the EBM is factory-installed in an IBM rack, these items are pre-assembled.
Table 6. EBM Accessory Kit (42R8076)
Quantity Eaton PN Description
1164201518 Powerware 240V Extended Battery Module (EBM 240) User’s Guide
1103002843-3992 Rail Hardware Kit (metric):
S(8) M5×12 Pan-Head Screws
S(8) M5×10 Flat-Head Screws
S(4) M5×16 Hex-Head Screws
S(4) M5 Clip Nuts
S(2) Square-Hole Adapter Plates
2157605902-003 Joining Brackets
4180500153-306 Joining Bracket Screws (M4×10 mm)
Table 7. FC 6571 PDM (42R4318)
Quantity Eaton PN Description
1103003918-3991 FC 6571 PDM
1103005205 Accessory Kit
S(1) Front Cover (157604790-002)
S(1) Powerware 9125 Two-in-One PDM (5000/6000 VA) User’s Guide (164201519)
S(2) Joining Bracket (157605902-003)
S(4) Joining Bracket Screws (M4×10 mm) (180500153-306)
INSTALLATION
EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1
4
Table 8. FC 6572 PDM (42R4319)
Quantity Eaton PN Description
1103003919-3991 FC 6572 PDM
1164201519 Powerware 9125 Two-in-One PDM (5000/6000 VA) User’s Guide
1103006383 Accessory Kit
S(1) Front Cover (157604790-002)
S(2) Joining Bracket (157605902-003)
S(4) Joining Bracket Screws (M4×10 mm) (180500153-306)
2152601971-001 IEC 320-C19 to IEC 320-C20, 16A Equipment Power Cords (4.4m/14 ft)
4152601942-001 IEC 320-C13 to C14, 10A Equipment Power Cords (1.8m/6 ft)
Setup and Installation
The Powerware 9125 E64 UPS is designed for flexible configurations
and can be installed in a rack, as a standalone cabinet, or in a tower
configuration.
NOTE For UPS rack installations: If the UPS is pre-installed in an IBM rack, continue
to “Installing the Internal Batteries” on page 12. If you are installing the UPS in an IBM
iSeries (0550, 0551, 0554, or 0555 types) or pSeries (7014 type) rack, continue to the
following section, “Tools Required.” If you have another type of rack, contact your service
representative (see page 49).
NOTE For UPS standalone cabinet or tower installations: Continue to “Installing
the Internal Batteries” on page 12 to begin the UPS setup.
Tools Required
To assemble the components, the following tools may be needed:
SMedium flat-bladed screwdriver
S#2 Phillips screwdriver
S8mmwrenchorsocket
INSTALLATION
EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1 5
Rack-Mount Setup
The rail kit can be mounted in 48-cm (19-inch) panel racks from 61 to
76 cm (24 to 30 inches) deep.
NOTE Mounting rails are required for each individual cabinet and are located in the UPS
and EBM cartons. The UPS requires 5U and each EBM requires 3U of rack height. All
hardware is supplied.
NOTE The UPS and any optional cabinets MUST be installed at the bottom of the rack. If
placed in a rack with existing equipment, the rack must be reconfigured to allow the UPS
installation at the bottom of the rack.
Each rail kit requires one (1) of each item in the following list:
SLeft adjustable rail assembly (located in the UPS and EBM cartons)
SRight adjustable rail assembly (located in the UPS and EBM cartons)
SRail hardware kit (located in the E64 UPS and EBM accessory kits)
To install the rail kit(s):
1. Loosen the assembly wing nuts on both rail assemblies and adjust
the rail size for the depth of your rack (see Figure 1).
Rear
Front Rail Assembly
Assembly Wing Nuts
Figure 1. Adjusting the Rail Depth
2. Select the proper holes in the rail for positioning the UPS and any
optional cabinets in the rack.
Place the first rail at the bottom, using positions 1 and 6 for the
front pan-head screws. If you are installing additional rails, place the
next rail 4 holes above the last installed screw (see Figure 2).
INSTALLATION
EATON Powerware®9125 (9910-E64) UPS Installation Guide for IBM®Applications S164201697 Rev 1
6
Position 1
Position 6
Position 10
Position 15
First Rail
Second Rail
Figure 2. Front Rack Screw Positions
3. Secure the rail to the front of the rack with two pan-head screws
and one adapter plate. Insert the screws through positions 3 and 4
oftherail(seeFigure3).
NOTE Do not tighten the screws until the UPS or EBM is installed.
Andere Handbücher für Powerware 9125
9
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Eaton UPS Handbücher
Eaton
Eaton Powerware 9135 Bedienungsanleitung
Eaton
Eaton Power Xpert 9395P-600/600 Bedienungsanleitung
Eaton
Eaton Powerware 9170+ Bedienungsanleitung
Eaton
Eaton 93PM IBC-L Bedienungsanleitung
Eaton
Eaton Powerware 9355 Bedienungsanleitung
Eaton
Eaton 5P 1150VA RM Bedienungsanleitung
Eaton
Eaton Powerware 9390 Bedienungsanleitung
Eaton
Eaton MX 4000 RT Gebrauchs- und Pflegehandbuch
Eaton
Eaton 9E10000i Bedienungsanleitung
Eaton
Eaton Powerware 9125 Bedienungsanleitung
Eaton
Eaton ModularEasy 9PXMEZ6Ki Bedienungsanleitung
Eaton
Eaton Eaton 5PX Bedienungsanleitung
Eaton
Eaton 5S 550 Bedienungsanleitung
Eaton
Eaton PW9340-80I-N Betriebsanleitung
Eaton
Eaton 1000L Bedienungsanleitung
Eaton
Eaton 9SX Series Bedienungsanleitung
Eaton
Eaton 5P 650 AU Bedienungsanleitung
Eaton
Eaton Powerware 9390-160/100 Bedienungsanleitung
Eaton
Eaton 93PM-150(400) Bedienungsanleitung
Eaton
Eaton 93E 30IAC-D Bedienungsanleitung
Beliebte UPS Handbücher anderer Marken
Pylontech
Pylontech Victron & Pylontech US5000 Bedienungsanleitung
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung
Mecer
Mecer ME-1000-WTU Bedienungsanleitung
Mustek
Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch
Emerson
Emerson Liebert NXL series Bedienungsanleitung
MAKELSAN
MAKELSAN BOXER SERIES Bedienungsanleitung
Block
Block PC-0524-400-0 Bedienungsanleitung
CyberPower
CyberPower CP585LCD Bedienungsanleitung
CyberPower
CyberPower Office Tower Series UPS 1000 Bedienungsanleitung
CyberPower
CyberPower BM100 Bedienungsanleitung
Best Power
Best Power 610 Bedienungsanleitung
Best Power
Best Power Unity/I UT3K Bedienungsanleitung
