Eaton Powerware 9170+ Bedienungsanleitung

Powerware 9170+Rail Kit

9- and 12-Slot Cabinets

Installation Guide

Powerware is a registered trademark of Eaton Power Quality Corporation.

Torx is a registered trademark of Textron, Inc.

reproduced in any way without the express written approval of Eaton Corporation.

EATON Powerware®9170+Rail Kit (9- and 12-Slot Cabinets) Installation Guide S164201420 Rev B

www.powerware.com

Rack-Mount Installation

To install a 9- or 12-slot uninterruptible power system (UPS) cabinet into

a rack, you must order a cabinet specifically designed for rack-mounting.

Nine- and 12-slot battery cabinets ASY-0749 and ASY-0750 are also

available for rack-mounting. These models can be installed in an

EIA-standard 48.3 cm (19”) equipment rack and include a rack-mounting

kit with the brackets and required hardware.

To install the UPS or battery cabinet in the equipment rack:

NOTE The 9- and 12-slot cabinets are heavy [9-slot: 72 kg (158 lb); 12-slot: 89 kg (196 lb)].

This procedure requires two people to lift and position the cabinet into the equipment rack.

Install the cabinet in the rack before installing power and battery modules and before making

connections to the intended power source.

1. Remove the four screws (two on either side) securing the top cover

of the cabinet. Carefully lift the cover straight up and off to avoid

stressing the front panel display. Set the cover aside.

2. Remove the cabinet side covers by lifting the top edge. No other

hardware must be detached. Store or discard the side covers.

3. Carefully replace the cabinet top cover and secure with the four

screws removed in Step 1. Position the cover lip to fit behind the

front panel display.

RACK-MOUNT INSTALLATION

EATON Powerware®9170+Rail Kit (9- and 12-Slot Cabinets) Installation Guide S164201420 Rev B

www.powerware.com

4. Install six metal clip nuts (nine clip nuts for 12-slot cabinets) onto

each side flange along the front of the cabinet (see Figure 1).

NOTE DO NOT install metal clip nuts in the bottom cabinet section.

Tab Slots

Metal Clip Nuts

Tab Slots

Metal Clip Nuts

Figure 1. Metal Clip Nut and Tab Slot Locations

RACK-MOUNT INSTALLATION

EATON Powerware®9170+Rail Kit (9- and 12-Slot Cabinets) Installation Guide S164201420 Rev B

www.powerware.com

5. Install two rack-mount ears (three for 12-slot cabinets) on each side

of the cabinet (see Figure 2).

Insert the two offset tabs on the rear edge of the ear into the

matching tab slots on the cabinet side frame (see Figure 1). Pivot

the ear forward until it is flush against the cabinet side frame.

Secure each ear with three 1/4-20×1/2”Phillips-head bolts; screw

the bolts into the metal clip nuts installed in Step 4.

NOTE DO NOT install rack-mount ears in the bottom cabinet section.

Rack-Mount Ear

Figure 2. Rack-Mount Ears Installed

RACK-MOUNT INSTALLATION

EATON Powerware®9170+Rail Kit (9- and 12-Slot Cabinets) Installation Guide S164201420 Rev B

www.powerware.com

6. Select the proper holes in the rail that position the cabinet at the

desired location in the rack.

7. Install one equipment rail on each side of the rack using four

10-32×1/2”flat-head screws per rail.

8. With one person lifting each side of the cabinet, position the cabinet

onto the two equipment rails (see Figure 3).

Carefully slide the cabinet into the equipment rack until the

rack-mount ears of the cabinet are flush with the front vertical rails

of the rack. Verify that the holes in the ears align with the holes in

the rack.

Equipment Rail

Figure 3. Rails Holding UPS Cabinet

RACK-MOUNT INSTALLATION

EATON Powerware®9170+Rail Kit (9- and 12-Slot Cabinets) Installation Guide S164201420 Rev B

www.powerware.com

9. Secure the cabinet in the rack using 10-32×1/2”Torx®screws or

other appropriate customer-specified screws.

10. Follow the instructions in the UPS user’s guide to install the power

and battery modules.

Service and Support

If you have any questions or problems with the UPS, call your Local

Distributor or the Help Desk at one of the following telephone numbers

and ask for a UPS technical representative.

United States: 1-800-356-5737 or 1-919-870-3149

Canada: 1-800-461-9166 ext 260

All other countries: Call your local service representative

Please have the following information ready when you call the Help

Desk:

SModel number

SSerial number

SVersion number (if available)

SDate of failure or problem

SSymptoms of failure or problem

SCustomer return address and contact information

If repair is required, you will be given a Returned Material Authorization

(RMA) Number. This number must appear on the outside of the package

and on the Bill Of Lading (if applicable). Use the original packaging or

request packaging from the Help Desk or distributor. Units damaged in

shipment as a result of improper packaging are not covered under

warranty. A replacement or repair unit will be shipped, freight prepaid for

all warrantied units.

NOTE For critical applications, immediate replacement may be available. Call the Help

Desk for the dealer or distributor nearest you.

*164201420B*

164201420 B

Andere Handbücher für Powerware 9170+

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Eaton UPS Handbücher

Eaton

Eaton Pulsar EX RT 5000 Bedienungsanleitung

Eaton

Eaton 1000L Bedienungsanleitung

Eaton

Eaton 93PM IBC-L Bedienungsanleitung

Eaton

Eaton Powerware 9130 Bedienungsanleitung

Eaton

Eaton Power Xpert Plus 1 Bedienungsanleitung

Eaton

Eaton MBP6Ki Bedienungsanleitung

Eaton

Eaton 9315 Bedienungsanleitung

Eaton

Eaton Powerware 9125 Bedienungsanleitung

Eaton

Eaton Powerware 9390 Bedienungsanleitung

Eaton

Eaton Powerware 9x55 series Handbuch

Eaton

Eaton 93E UPS Bedienungsanleitung

Eaton

Eaton 93PM 150 kW SIAC-B Three-Wire Bedienungsanleitung

Eaton

Eaton BladeUPS Series Bedienungsanleitung

Eaton

Eaton Pulsar Series Bedienungsanleitung

Eaton

Eaton 20000i Bedienungsanleitung

Eaton

Eaton Ellipse MAX 600 Bedienungsanleitung

Eaton

Eaton POWERWARE Plus 18 Bedienungsanleitung

Eaton

Eaton Power Xpert 9395 Bedienungsanleitung

Eaton

Eaton Powerware BladeUPS Bar Bedienungsanleitung

Eaton

Eaton Power Xpert 9395P Bedienungsanleitung

Eaton

Eaton 9SX Series Bedienungsanleitung

Eaton

Eaton 93PM IBC-L Bedienungsanleitung

Eaton

Eaton 9E 10000i Bedienungsanleitung

Eaton

Eaton Ellipse PRO 650 FR Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung