Eaton Tripp Lite SmartPro Series Montageanleitung

p/n: 614-40194

Revision 01

SMART2200RM2U

SMART2200RM2UN

SMART3000RM2U

SMART3000RM2UN

SMART750RMXL2U

SMART750RMXL2UN

SMART1000RMXL2U

SMART1000RMX2UN

SMART1500RMXL2U

SMART1500RMXLN

SMART2200RMXL2U

SMART2200RMXLN

SMART3000RMXL2U

SMART3000RMXLN

BP48VRM2U BP72VRM2U

Advanced User Guide

Eaton®Tripp Lite Series SmartPro

Eaton reserves the right to change specifications without prior notice. Eaton is a registered trade ark of Eaton. All other trade arks are

property of their respective co panies.

express written approval of Eaton.

SSaaffeettyy IInnssttrruuccttiioonnss

SAVE THESE INSTRUCTIONS. This manual contains important instructions that should be

followed durin installation and maintenance of the UPS and batteries.

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense

This is a category C2 UPS product In a residential environment, this product may cause radio

interference, in which case the user may be required to take additional measures

Supplier's Declaration of Conformity of Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules Operation is subject to the following two

conditions:

1 this device may not cause harmful interference, and

2 this device must accept any interference received, including interference that may cause

undesired operation

For questions regarding this FCC SDoC declaration, contact Eaton Corporation by telephone or

through the Internet

Eaton Corporation 8609 Six Forks Road,

Raleigh, NC 27615, USA

Telephone: 800-356-5794

SSppeecciiaall SSyymmbboollss

The following are examples of symbols used on the product to alert you to important information:

RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of

electric shock sy bol.

CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's

anual for additional infor ation, such as i portant operating and aintenance

instructions.

Infor ation, advice, help.

Read the docu entation provided.

Disconnect input plug.

Before aintenance, first shut down the UPS then disconnect the AC power

source, internal and external batteries then discharge capacitors by pressing the

ON button and wait 5 inutes.

This equip ent should only be used in a dry indoor environ ent.

Operating range of te perature.

Operating range of hu idity.

The UPS and their batteries ust be kept in a ventilated place.

SSaaffeettyy ooff PPeerrssoonnss

• The system has its own power source (the battery) Consequently, the power outlets may be

energized ven if the systems is disconnected from the AC power source Dangerous voltage

levels are resent within the system It should be opened exclusively by qualified service

personnel

• The system must be properly grounded at all times

• The battery supplied with the system contains small amounts of toxic materials To avoid

accidents, the directives listed below must be observed:

–Servicing of batteries should be performed or supervised by personnel knowledgeable about

batteries and the required precautions

–When replacing batteries, replace with the same type and number of batteries or battery

packs

–Do not dispose of batteries in a fire The batteries may explode

–Batteries constitute a danger (electrical shock, burns) The short-circuit current may be very

high

• Precautions must be taken for all handling:

–Wear rubber gloves and boots

–Do not lay tools or metal parts on top of batteries

–Disconnect charging source prior to connecting or disconnecting battery terminals

–Determine if battery is inadvertently grounded If inadvertently grounded, remove source

from ground Contact with any part of a grounded battery can result in electrical shock The

likelihood of such shock can be reduced if such grounds are removed during installation and

maintenance (applicable to equipment and remote battery supplies not having a grounded

supply circuit)

PPrroodduucctt SSaaffeettyy

• To connect the UPS, instructions and operation described in the manual must be followed in the

indicated order

• CAUTION - To reduce the risk of fire, the unit connects only to a circuit provided with 20 or 30

amperes maximum branch circuit overcurrent protection in accordance with the National Electric

Code, ANSI/NFPA 70 (US installations only)

• Check that the indications on the rating plate correspond to your AC powered system and to the

actual electrical consumption of all the equipment to be connected to the system

• For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall

be easily accessible

• Never install the system near liquids or in an excessively damp environment

• Never let a foreign body penetrate inside the system

• Never block the ventilation grates of the system

• Never expose the system to direct sunlight or source of heat

• If the system must be stored prior to installation, storage must be in a dry place

• The admissible storage temperature range is -25ºC to +55ºC without batteries, 0°C to 40°C with

batteries

• The system is not for use in a computer room AS DEFINED IN the standard for the Protection of

Information Technology Equipment, ANSI/NFPA 75 (US installations only)

SSppeecciiaall PPrreeccaauuttiioonnss

• The unit is heavy: wear safety shoes and use vacuum lifter preferentially for handling operations

• All handling operations will require at least two people (unpacking, lifting, installation in rack

system)

• Before and after the installation, if the UPS remains de-energized for a long period, the UPS must

be energized for a period of 24 hours, at least once every 6 months (for a normal storage

temperature less than 25°C) This charges the battery, thus avoiding possible irreversible

damage

• During the replacement of the Battery Module, it is imperative to use the same type and number

of element as the original Battery Module provided with the UPS to maintain an identical level of

performance and safety If there are any questions, don’t hesitate to contact your local Eaton

representative

• All repairs and service should be performed by AUTHORIZED SERVICE PERSONNEL ONLY

There are NO USER SERVICEABLE PARTS inside the UPS

• For potential safety issue on defective UPS : DISCONNECT INTERNAL BATTERY for storage and

transportation

Tripp Lite by Eaton S artPro Advanced User Guide 614-40194—Rev 01 vii

TTaabbllee ooff CCoonntteennttss

11 IInnttrroodduuccttiioonn....................................................................................................................................................................................................................................................................................................11

1 1 Environmental protection 2

1 2 Benefits 3

1 3 Special Precautions 3

22 PPrreesseennttaattiioonn ..................................................................................................................................................................................................................................................................................................55

2 1 Standard installation 5

2 2 Rear panel 6

2 3 Optional accessories 7

33 IInnssttaallllaattiioonn ......................................................................................................................................................................................................................................................................................................99

3 1 Inspecting the equipment 9

3 2 Recommended Positions 10

3 3 Connecting the Internal Battery 13

3 4 EBM Connection 13

3 5 UPS connection 15

3 6 Connection with a FlexPDU (Power Distribution Unit) optional module 16

3 7 Connection with a HotSwap MBP (Maintenance ByPass) optional module 16

3 7 1 UPS Start-Up with the HotSwap MBP Module 17

3 7 2 HotSwap MBP module test 17

44 IInntteerrffaacceess aanndd CCoommmmuunniiccaattiioonn .......................................................................................................................................................................................................................................... 1199

4 1 Control panel 19

4 2 LCD Description 19

4 3 Display functions 22

4 4 User settings 24

4 5 Communication ports 26

4 6 UPS Remote Control Functions 27

4 7 Power Alert Software 30

4 8 Cybersecurity 30

55 OOppeerraattiioonn........................................................................................................................................................................................................................................................................................................ 3311

5 1 Start-up and normal operation 31

5 2 Starting the UPS on battery 31

5 3 UPS shutdown 31

5 4 Operating modes 32

5 5 Return of AC input power 32

5 6 Configuring Battery Settings 32

5 7 Retrieving the event and fault log 33

66 PPSS MMaaiinntteennaannccee................................................................................................................................................................................................................................................................................ 3355

6 1 Equipment Care 35

viii Tripp Lite by Eaton S artPro Advanced User Guide 614-40194—Rev 01

6 2 Storing the Equipment 35

6 3 When to Replace Batteries 35

6 4 Replacing Batteries 35

6 5 Replacing the UPS Equipped with a HotSwap MBP 37

6 6 Recycling the Used Equipment 38

77 TTrroouubblleesshhoooottiinngg .................................................................................................................................................................................................................................................................................. 3399

7 1 Typical Alarms and Faults 39

7 2 Detail Alarm or Fault Code 40

7 3 Silencing the Alarm 41

7 4 Service and Support 41

88 SSppeecciiffiiccaattiioonn aanndd TTeecchhnniiccaall CChhaarraacctteerriissttiiccss.................................................................................................................................................................................................... 4433

8 1 UPS Model List 43

8 2 Extended Battery Module Model List 44

8 3 Weights and Dimensions 44

8 4 Electrical Input 45

8 5 Electrical Input Connections 45

8 6 Electrical Output 46

8 7 Electrical Output Connection 46

8 8 Battery 48

8 9 Environmental and Safety 48

99 GGlloossssaarryy .......................................................................................................................................................................................................................................................................................................... 4499

Table of Contents

Tripp Lite by Eaton S artPro Advanced User Guide 614-40194—Rev 01 ix

LLiisstt ooff FFiigguurreess

Figure 1 Rack Installation Steps 10

Figure 2 Tower Installation Steps 12

Figure 3 LCD Screen — Example 20

Figure 4 Network Card 27

Figure 5 Relay Output Details 30

Figure 6 SmartPro 750 / 1000 / 1500 models 43

Figure 7 SmartPro 2200/3000 models 43

x Tripp Lite by Eaton S artPro Advanced User Guide 614-40194—Rev 01

List of Figures

Andere Handbücher für Tripp Lite SmartPro Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Eaton UPS Handbücher

Eaton

Eaton 9PX 1000i RT2U Bedienungsanleitung

Eaton

Eaton 3S Bedienungsanleitung

Eaton

Eaton 5E 100i USB Bedienungsanleitung

Eaton

Eaton 5PX 1500i RT2U Bedienungsanleitung

Eaton

Eaton Ellipse ECO 500 Bedienungsanleitung

Eaton

Eaton 5S Bedienungsanleitung

Eaton

Eaton 9PX6KIRTN-L Bedienungsanleitung

Eaton

Eaton Powerware BladeUPS Bedienungsanleitung

Eaton

Eaton BladeUPS none Bedienungsanleitung

Eaton

Eaton Powerware 9x55 series Handbuch

Eaton

Eaton Ellipse PRO 650 Bedienungsanleitung

Eaton

Eaton 93PM G2 Series Handbuch

Eaton

Eaton Powerware 9390-160/100 Bedienungsanleitung

Eaton

Eaton 5S 550 Bedienungsanleitung

Eaton

Eaton Powerware 9155 Bedienungsanleitung

Eaton

Eaton 1000H(XL) Bedienungsanleitung

Eaton

Eaton Powerware 5125 Bedienungsanleitung

Eaton

Eaton Eaton 5PX Montageanleitung

Eaton

Eaton Power Xpert 9395 550/275 Bedienungsanleitung

Eaton

Eaton EX 700 Bedienungsanleitung

Eaton

Eaton 93P Handbuch

Eaton

Eaton Powerware 9155 Bedienungsanleitung

Eaton

Eaton Ellipse ECO 500 Bedienungsanleitung

Eaton

Eaton 5E Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung