ECD V-M.O.L.E. Bedienungsanleitung
QUICK REFERENCE GUIDE
1
Welcome: 2
Equipment:
Features/Functions 3
Setup:
Charging the Power Pack 5
Software Installation 6
Communications 7
Operation:
Introduction 9
Step 1: Setup Instrument 10
Step 2: Data Collection 15
Step 3: Download Data 18
CONTENTS
2
WELCOME
This Quick Reference Guide is designed to help the user to familiarize themselves with
the equipment, perform basic hardware setup/communications and operation. For
detailed information on both Hardware & Software components, please refer to the Help
system accessible in the M.O.L.E.®MAP Software.
To access the help system start the software and use any of the methods listed:
1) Select the Help Button on the Toolbar.
2) Pressing the shortcut key [F1]
3) On the Help menu, click MAP Help.
3
EQUIPMENT - FEATURES/FUNCTIONS
Activity Indicators:
Indicates state of the
M.O.L.E. Thermal Proler
OK Button:
Invokes "OK" process resulting
in a GO-NO GO decision
Thermocouple/Inputs:
Type “K”Thermocouple
sensor connection
ON/OFF Button:
Turns the Proler "ON/OFF"
Data/Charging Port:
Transfers data to/from a
computer & charges the
internal Power Pack
Record Button:
Starts/Stops recording data.
Charging LED:
Indicates when the internal
Power Pack is charging
4
EQUIPMENT - STATUS ACTIVITY LED
Activity Indicator Action LED Color
ON/OFF Indicates Proler is "ON"
and idle
Green (Solid)
Record Indicates Proler is
recording data
Green (Flashing)
OK
Indicates recorded prole
passes pre-congured criteria
Green - Pass (Solid)
Red - Fail (Solid)
Temp(erature) Indicates if internal temp is
at or above a max
Red (Solid) >40°C
Battery Indicates when the internal
Power Pack voltage is low
Red (Solid) <3.0V
Charge Indicates when the internal
Power Pack is charging
Yellow (Solid)
1
2
5
SETUP - CHARGING THE POWER PACK
1. Insert the USB computer interface cable into
a computer USB Port
2. Insert the other end into the Data/Charging
Port.
A completely discharged Power Pack
takes about 8 hours to be fully
charged. For quick charges, it can be
charged for 15 minutes allowing one
10 minute data run to be performed.
2
6
SETUP - SOFTWARE INSTALLATION
The user must have administrator permis-
sions for the computer to install the software
1. Insert the Flash Drive in a USB Port and the
AutoPlay menu appears.
2. Select Open folder to view files button on the
AutoPlay menu to launch Windows® Explorer.
Closely follow the instructions for your operating
system. For detailed information view the
Installation Help file on the Flash Drive.
1
2
3
7
1. Insert the USB computer interface cable into
a computer USB Port
2. Insert the other end into the Data/Charging
Port.
3. Start M.O.L.E.®MAP
SETUP - COMMUNICATIONS
4
5
6
8
SETUP - COMMUNICATIONS
4. On the M.O.L.E.®menu, click the
Select Instrument command.
5. Select the desired instrument from the dialog
box. If there are none displayed, click the
Scan for Instruments command button to
detect all available instruments.
6. Click the OK command button to accept.
9
OPERATION - INTRODUCTION
This operation procedure guides you through a typical process on how to set a
M.O.L.E.
®
Profiler up for performing a data run. For additional detail, consult the Help
System in the software.
The M.O.L.E.
®
Thermal Profiler depends on the MAP (Machine-Assembly-Process)
software to control how it collects and interprets data. Several kinds of data runs may
need to be performed to achieve desired information, or the same data run may be
performed repeatedly over time to monitor one process. Either way, each data run must
be set up at least once.
The MAP software includes wizards that help you get started quickly, even if you are a
beginner or infrequent user.
Inhaltsverzeichnis
Andere ECD Messgerät Handbücher
ECD
ECD H10C Bedienungsanleitung
ECD
ECD WaveRIDER Series Installationshandbuch
ECD
ECD M.O.L.E. EV20 Bedienungsanleitung
ECD
ECD TC80 Bedienungsanleitung
ECD
ECD FCA-22 Bedienungsanleitung
ECD
ECD HCA1 Bedienungsanleitung
ECD
ECD DO82 Bedienungs- und Wartungshandbuch
ECD
ECD L20 Bedienungsanleitung
ECD
ECD MOLE EV6 Bedienungsanleitung
