Ecom J2KNpro Tech Bedienungsanleitung

Operating Instructions

WE PRODUCE QUALITY OF LIFE!

Page 2 ecom-J2KN

pro

Index Page

Important hints 3

Important hints for using IR bench 4

1. Instrument design

1.1. Basic module 5

1.2. Control module 6

2. Gas cooler (option) 7

3. Power supply 8

4. Radio communication basic/control module 9

5. Data record 10

6. Instrument switch on 11

7. Input or selection of combustion plants 13

8. Flue gas analysis

8.1. Gas analysis 16

8.2. CO measurement (gas channel check) 19

8.3. O

check 20

8.4. Flow measurement (option) 20

8.5. Draught measurement 21

8.6. Soot dot...Oil trace 22

8.7. Measurement record and printout 24

8.8. Printout ecom-J2KN

pro

9. Mean Value Measurement 26

10. Adjustments 28

11. Control 33

12. Data processing

12.1 Communication 34

12.2. Automatic Measurement (option) 35

12.3. Data logger 36

12.4. Data logging with DASNT2 37

12.5. Data processing with DAS5 37

12.6. Data processing with Remote Display App 38

13. Diagnostics

13.1. Fault diagnostic 39

13.2. dT-measrurement 41

13.3. Heating check (option) 41

14. Maintenance tips 45

15. Technical data 48

16. FAQ 49

ecom-J2KN

pro

Page 3

Important hints

The ecom

J2KN

pro

meets

the requirements of

DIN EN 50379 part of 2.

The

ecom

J2KN

pro

may

not be used for

continuous emission control!

Following minimum times must be kept, in order

to receive correct measured values:

-1 min. to calibrate the sensors at fresh air

-2 min. for stable measured values

The following substances impair the working of

the instrument:

-Cleaning agents

-Degreasers

-Wax polishes

-Adhesives

-Formaldehyde

Adjustments at burners and boilers

should be made

only by specialists, who are familiar with

this installations!

1. Charge the accumulator regularly (Charge not

used instrument min. once a month)!

2. Never store the instrument with unloaded

battery!

Page 4 ecom-J2KN

pro

Important hints for using IR bench

Please start every 15 min. a fresh air calibration by

using the infrared bench (especially with methane) to

get accurate measurements

(Adjustments / Re-Calibration)!

Please switch on the instrument 15 min. before star

ing the fresh air calibration, in order to bring the in-

frared bench on operating temperature!

ecom-J2KN

pro

Page 5

1. Instrument design

1.1. Basic module

Connection

air

temperature

Connection

gas tem-

perature

Condensate

trap with fine

dust filter

Connection

gas hose

Connection

draught

Connection

pressure

Con

nection

condensate

evacuation

Integral

printer

Filter for

IR bench

Control

module

(see next page)

Connection mains

power plug

with fuse

(630 mA / 250 V)

Info display

(see chap-

ter 11.)

Basic

ON / OFF

Analogue

inputs

(Option)

Connection

heatet probe

(Option)

Connection

AUX

SO2/NOx-

filter for

CO sensor

Connections

pitot tube

(Option)

Cable socket

by wire transfer

basic / control

modules

Page 6 ecom-J2KN

pro

1.2. Control module

ESC key

(quit/

escape menu)

In the input mode,

the keys are used

for numerical inputs

OK key

(confirm selec-

tion)

Cursor keys

(Up/Down/Right/

Left/Scroll)

Measurement

values record-

ing

Print key

(access to

printing menu)

Switch ON/OFF

control module

Display

backlit

ON/OFF

Function keys

(function shown on display)

Slot for Multi-

Media-Card

Graphics

display

Connection

USB

Connection

keyboard

Socket for connection

cable by wire

transfer basic

Keyboard control module

Connection air

temperature

ecom-J2KN

pro

Page 7

2. Gas cooler (option)

Exhaust gas with a temperature over the steam dew point (35 to

65 °C) is flown spiral via a long gas path thru a surface coated metal

body with good thermal conductivity. The gas radiates its heat to this

metal body. A PELTIER element (semiconductor cooling element)

flown by a continuous current is thermally connected with this body

and with a second metal body with cooling ribs and ventilation slots.

The flow thru the PELTIER element creates a heat transfer from

WARM to COLD, drains the heat of the metal body flown by gas and

conveys it to the outer cooling body. This heat is conveyed thru a

vertical forced ventilation to the surrounding air.

The condensation issued by the heat loss of the gas drops in a re-

ceptacle and is pumped out on request (either by the user or due to

the level monitoring) by a periodically working hose pump.

The sucking capacity of the gas conveying pump avoids a sufficient

dwell time of the gas with the condensate, so that wash out reactions

(NO

O > H

) do not take place.

At the cooler outlet the gas has a temperature of ca. 5 °C with a rela-

tive saturation of nearly 100 % relative humidity (corresponds to a

water steam content < 7 g/m

Fan

Peltier

element

Gas

outlet

Gas

inlet

Level control

Condensate

evacuation

In case of

battery operation the power is reduced

(output temperature 8 – 10 °C)!

COLD

Page 8 ecom-J2KN

pro

3. Power supply

The basic module of the ecom-J2KN

pro

is delivered with internal

loading unit. The instrument can be operated upon a longer time

period with the internal accumulator (6 V; 7,2 Ah). Connecting the

internal charging unit to mains power is only compulsory to recharge

the accumulators and to operate the heated probe system.

The accumulators should be recharged when the instrument shows a

corresponding message (acoustical warning and display infor-

mation). The accumulators loading stand can be checked, looking at

the voltage information on the display (menu "Control"). The battery

warning is activated when the value „ACC.B“ is smaller than 6 V.

By 5,8 V the power operation via battery is no more possible. The

instrument must be further powered via internal charging unit.

The control module of the ecom-J2KN

pro

is powered by 3 nickel-

metal-hydride accumulators (type AA). In case of need, the accumu-

lators can be recharged by docking the control module to the basic

module.

Hereby 2 functions can be selected („Adjustments / „Internal“ /

„Reloading function“ / <OK>):

1. Recharging function ON (<F1> = YES):

- batteries slowly and carefully recharged

- recommended adjustment by frequent use

2. Recharging function OFF (<F4> = NO):

- batteries quickly recharged

- recommended adjustment by occasional use

Used accumulators c

an be returned to us or brought

to recycling stations of public waste disposal compa-

nies respectively accumulators selling stores!

Never use batteries, to operate the control

module of the J2KN

pro

ecom-J2KN

pro

Page 9

4. Radio communication basic / control module

Thanks to the detachable control mod-

ule the basic module can be monitored

wireless. The basic module can be un-

locked as follows:

1. Press to unlock.

2. Tip control module forwards

3. Release control module from basic

module

The information exchange between

control and basic module is performed

via radio transmission (868 MHz) with a

coverage of approx. 50 m (by free

sight). The quality of the radio transmis-

sion is documented by a bar indication

in the main menu of the instrument

(long bar = good radio communication).

By interruption of the radio

communication, an error message is

displayed. By persisting disturbances of

the radio communication, a cable

(option) can take over the transfer

(connection betwen socket DATA on

control unit and socket DATA on basic

module).

If the basic module is switched off and

the control module not, so the display

will show an error message inviting to

fix the control module in its docking

station (helps also not to forget the con-

trol module). Observe this order, quit

with <ESC> and finally switch off the

control module.

Gas analysis

Pressure

Soot..Oil trace

Data processing

Adjustments

Control

Diagnostics

Unlocking

Bar indication

radio quality

ECOM

J2 N

Radio connection

interrupted!

Use cable or

switch on basic

module!

Quit with:

-- ECOM-J2 N --

Place J2 N in

basic mod.!

Quit with:

Page 10 ecom-J2KN

pro

5. Data record

The multi-media card enables the storage of both punctual meas-

urements and data logger records.

The values of punctual measurements are written in a text file

(J2KDV.txt). Those of data logger records in a csv file (J2KDL-xx.csv

/ xx = records numbered consecutively).

Both file types have the same structure and can be imported respec-

tively opened in Excel. See chapter „Technical Data“ for data format

information. The files can be transferred on the PC using a card

reader. The following conditions must be fulfilled for using a multi-

media card:

- ecom-J2KN

pro

- min. card volume 32 MB - max.32 GB (UHC)

- card formatted on 16 bit FAT or FAT32

- SD cards from SanDisk recommended

- PC with card reader

Insert the multi-media card as shown.

Take care that the card does not stand

out and hooks on.

Never pull out cards during

data record

data loss

and damaging of the data carrier possible!

Andere Handbücher für J2KNpro Tech

Inhaltsverzeichnis

Andere Ecom Messgerät Handbücher

Ecom

Ecom DP Bedienungsanleitung

Ecom

Ecom ECOM-D Bedienungsanleitung

Ecom

Ecom J2KN Bedienungsanleitung

Ecom

Ecom i.roc Ci70 -Ex Montageanleitung

Ecom

Ecom EN3 Bedienungsanleitung

Ecom

Ecom EN2-F Bedienungsanleitung

Ecom

Ecom ecom-DP Bedienungsanleitung

Ecom

Ecom EN2 Bedienungsanleitung

Ecom

Ecom Ecom-B Bedienungsanleitung

Ecom

Ecom B Bedienungsanleitung

Ecom

Ecom LSG Bedienungsanleitung

Ecom

Ecom EN3 Bedienungsanleitung

Ecom

Ecom EN2 Bedienungsanleitung

Ecom

Ecom J2KNpro Tech Bedienungsanleitung

Ecom

Ecom Quad Dock Ethernet Bedienungsanleitung

Ecom

Ecom Ex-MX2 Montageanleitung

Ecom

Ecom ECOM-D Bedienungsanleitung

Ecom

Ecom ecom-AK Bedienungsanleitung

Ecom

Ecom J2KNpro Tech Bedienungsanleitung

Ecom

Ecom ST Bedienungsanleitung

Ecom

Ecom DP Bedienungsanleitung

Ecom

Ecom Ex-Tacho 10 Bedienungsanleitung

Ecom

Ecom ecom-LSG Bedienungsanleitung

Ecom

Ecom Ex-MP4 a Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung