ECS L7SOM Bedienungsanleitung

Preface

This publication, including all photographs, illustrations and software, is protected un-

of the material contained herein, may be reproduced without writtenconsent ofthe au-

thor.

Version 3.0

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any par-

ticular purpose. The manufacturer reserves the right to revise this publication and to

make changes from time to time in the content hereof without obligation of the manu-

facturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective owners

and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digi-

tal device, pursuant to Part 15 of the FCC Rules. These limitsare designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not oc-

cur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

−Reorient or relocate the receiving antenna.

−Increase the separation between the equipment and the receiver.

−Connect the equipment onto an outlet on a circuit different from that to which

the receiver is connected.

−Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system's manu-

facturer could void the user's authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing conditions:

−This device may not cause harmful interference, and

−This device must accept any interference received, including interference

that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Mainboard Describes features of the mainboard,

and provides a shipping checklist.

Go to ⇒page 1

Chapter 2

Installing the Mainboard Describes installation of mainboard

components.

Go to ⇒page 7

Chapter 3

Using BIOS Provides information on using the BIOS

Setup Utility.

Go to ⇒page 25

Chapter 4

Using the Mainboard Software Describes the mainboard software.

Go to ⇒page 48

iii

Preface i

Features and Packing List Translations 錯誤!尚未定義書籤。

CHAPTER 1 1

Introducing the Mainboard 1

Introduction............................................................................................................1

Checklist.................................................................................................................1

Standard Items ...................................................................................................1

Features..................................................................................................................2

Choosing a Computer Case................................................................................4

Mainboard Components.......................................................................................5

CHAPTER 2 7

Installing the Mainboard 7

Safety Precautions................................................................................................7

Quick Guide...........................................................................................................7

Installing the Mainboard in a Case.....................................................................8

Checking Jumper Settings...................................................................................8

Setting Jumpers .................................................................................................8

Checking Jumper Settings.................................................................................9

Jumper Settings.................................................................................................9

Connecting Case Components.........................................................................11

The Panel Connectors......................................................................................12

Installing Hardware.............................................................................................12

Installing the Processor...................................................................................12

InstallingMemoryModules............................................................................15

Installing a Hard Disk Drive/CD-ROM ..........................................................16

Installing a Floppy Diskette Drive ..................................................................17

InstallingAdd-on Cards..................................................................................18

Connecting Optional Devices..........................................................................20

ConnectingI/ODevices.....................................................................................23

External Connector Color Coding...................................................................24

CHAPTER 3 25

Using BIOS 25

About the Setup Utility........................................................................................25

The Standard Configuration............................................................................25

Entering the Setup Utility................................................................................26

Updating the BIOS..........................................................................................26

Using BIOS..........................................................................................................27

Standard CMOS Features................................................................................28

Advanced BIOS Setup Option........................................................................30

Advanced Chipset Features Option.................................................................33

IntegratedPeripheralsOption..........................................................................35

Power Management Setup Option...................................................................40

PNP/PCI Configuration Option.......................................................................43

PC Health Status Option..................................................................................44

Frequency/Voltage Control..............................................................................45

LoadFail-Safe Defaults Option......................................................................46

Load Optimized Defaults Option....................................................................46

Set Supervisor and User Passwords Options...................................................46

Save & Exit Setup Option...............................................................................47

Exit Without Saving........................................................................................47

CHAPTER 4 48

Using the Mainboard Software 48

About the Software CD-ROM............................................................................48

Auto-installing under Windows 98....................................................................48

Running Setup.................................................................................................49

Manual Installation..............................................................................................51

Utility Software Reference.................................................................................51

Award Flash Memory Utility...........................................................................51

PC-CILLIN......................................................................................................51

MediaRing Talk –Telephony Software...........................................................52

Super Voice –Fax/Modem Software...............................................................52

WinFlash Utility..............................................................................................52

CD Ghost.........................................................................................................52

Recovery Genius.............................................................................................52

Language Genius.............................................................................................52

PageABC.........................................................................................................52

Introducing the Mainboard

Congratulations on purchasing the L7SOM mainboard. The L7SOM main-

board is an Micro ATX mainboard that uses a 4-layer printed circuit board and

measures 244 mm x 244 mm. The mainboard features a Socket 462 that ac-

commodates AMD Athlon processors supporting frontside bus (FSB) speeds

up to 266 MHz.

The L7SOM incorporates the SiS740 Northbridge and SiS961 (or SiS961B

/SIS962) Southbridge chipsets which combine support for the new high-

bandwidth Double Data Rate (DDR) 266 SDRAM, and the AC 97 audio codec.

Note: SDRAM provides 800 MBps or 1 GBps data transfer depending on

whether the bus is 100 MHz or 133 MHz. Double Data Rate SDRAM

(DDR SDRAM) doubles the rate to 1.6 GBps or 2.1 GBps by transferring

data on both the rising and falling edges of the clock. DDR SDRAM uses

additional power and ground lines and requires 184-pin DIMM modules

rather than the 168-pin DIMMs used by SDRAM.

Compare the mainboard’s package contents with the following checklist:

Standard Items

•One mainboard

•One diskette drive ribbon cable

•One IDE drive ribbon cable

•One auto-install software support CD

•One 1394 bracket (optional)

•This user’s manual

Processor The mainboard uses an AMD 462-pin Socket A that has the

following features:

•Supports 200/266 MHz frontside bus (FSB)

•Accommodates AMD Athlon Duron, Athlon, and Athlon XP

processors.

The SiS740 Northbridge and SiS961 Southbridge chipsets are

based on an innovative and scalable architecture with proven

reliability and performance. A few of the chipset’s advanced

features are:

•Integrated DRAM controller supports memory bus up to

266 MHz

•A 16-bit bi-directional data bus provides high I/O throughput

•Integrated 2D/3D accelerator providing high graphics

performance

•A low 2.5-volt DDR266 SDRAM power consumption

which makes it an excellent solution for notebooks and

desktops with a small footprint

•Built in GDI+ accelerator

•An ATA 100 interface on the chipset, which helps boost

system performance by providing a high-speed connec-

tion to ATA 100 Hard Disk Drives, delivering maximum

sustained data transfer rates of 100 MB/sec

Additional key features include support for six USB ports, an

AC 97 link for audio and modem, hardware monitoring, and

ACPI/OnNow power management.

Chipset

This mainboard may support either one of the three

Southbridge chipset. Refer below for details:

•SiS961 Southbridge –supports ATA100 interface and

six USB ports.

•SiS961B Southbridge –supports ATA133 interface and

six USB ports.

•SiS962 Southbridge –supports ATA133 interface and

six USB ports including onboard USB 2.0 and IEEE

1394A controller.

USB USB 1.1

The SiS961 or SiS961B Southbridge chipset features the USB

1.1 specification which can support for six USB ports.

However, if the mainboard comes with SiS962 Southbridge

chipset, then the mainboard supports the USB 2.0 specifica-

tion.

USB 2.0 (optional)

The USB 2.0 Controller is compliant with Universal Serial Bus

Specification Revision 2.0.

The USB 2.0 supports data transfer rates up to 480MB/sec for

high-speed devices and specifies a microframe that will be

1/8th of a 1msec frame. This allows the USB 2.0 devices to

have small buffers even at high data rates.

The USB 1.1 connectors and other full speed cables can sup-

port the higher speed of USB 2.0 without any changes.

The chipset has the following advanced USB features:

•Compliant with Enhanced Host Controller Interface

(EHCI) Specification Revision 0.95 and Universal Host

Controller Interface (UHCI) Specification Revision 1.1

•PCI multi-function device consists of two UHCI Host Control-

lers for full/low-speed signaling and one EHCI Host

•Controller core for high-speed signaling

•Supports PCI-Bus Power Management Interface Specifi-

cation release 1.1

•Legacy support for all downstream facing ports

IEEE 1394A Con-

troller Interface

(optional)

•Fully supports provisions of IEEE 1394-1995 and P1394A

for high performance serial bus

•Provides two fully compliant cable ports at 100/200/400

Mbits and operates in one, two or three port mode

•Single 24.576 MHZ crystal provide transmit/receive data

at 100/200/400 Mbits/s and LLC clock at 49.152 M

•Separate cable bias (TPBIAS) and driver termination

voltage supply for each port

•Support power-down feature to conserve energy in bat-

tery powered applications

Memory The mainboard accommodates DDR200/266 DDR SDRAM (Dou-

ble Data Rate Synchronous DRAM) up to 2 GB using two 2.5V

unbuffered DIMM modules.

AC 97 Audio

Codec The AC 97 Audio codec is compliant with the AC 97 2.2 speci-

fication, and supports 18-bit ADC (Analog Digital Converter)

and DAC (Digital Analog Converter) resolution as well as 18-bit

stereo full-duplex codec with independent and variable sam-

pling rates. Further features include support for six analogline-

level stereo inputs.

Expansion

Options The mainboard comes with the following expansion options:

•Three 32-bit PCI slots

•A Communications Network Riser (CNR) slot

•Two IDE connectors which support four IDE channels and

a floppy disk drive interface

The L7SOM supports Ultra DMA bus mastering with transfer

rates of 33/66/100 MB/sec.

Note: If the mainboard incorporates the SiS961B or

SiS962 Southbridge chipset, the Ultra DMA bus

mastering can support up to 133 MB/sec transfer

rate. For SiS961 Southbridge chipset, the transfer

rate can support up to 100MB/sec only.

Integrated I/O The mainboard has a full set of I/O ports and connectors:

•Two PS/2 ports for mouse and keyboard

•One serial port

•One VGA port

•One parallel port

•One MIDI/game port

•One LAN port

•Two USB ports

•Audio jacks for microphone, line-in and line-out

Onboard LAN

(optional) The Realtek RTL8100 LAN chip is incorporated in the chipset

providing the mainboard with integrated Ethernet PCI LAN

capabilities.

VGA The mainboard has a built-in high performance, quality 2D/3D

graphics accelerator. The graphics system supports the Ultra-

AGP II ™ with 2GB/s bandwidth architecture and uses a

shared memory scheme that allows up to 64MB of system

memory to be used as video memory.

BIOS

Firmware This mainboard uses Award BIOS that enables users to con-

figure many system features including the following:

•Power management

•Wake-up alarms

•CPU parameters

•CPU and memory timing

The firmware can also be used to set parameters for different

processor clock speeds.

There are many types of computer cases on the market. The mainboard com-

plies with the specifications for the Micro ATX system case. Some features on

the mainboard are implemented by cabling connectors on the mainboard to

indicators and switches on the system case. Ensure that your case supports

all the features required. The mainboard can support one or two floppy disk-

ette drives and four enhanced IDE drives. Ensure that your case has sufficient

power and space for all the drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that

the I/O template in the case matches the I/O ports installed on the rear edge

of the mainboard.

This mainboard has a Micro ATX form factor of244 mm x 244 mm. Choose a

case that accommodates this form factor.

Table of Mainboard Components

Label Component

ATX1 Power connector

AUDIO1 Front-oriented microphone/line-out port header

BT1 Three volt realtime clock battery

CASEFAN1 Auxiliary case cooling fan

CDIN1 Primary CD-in connector

CDIN2 Secondary CD-in connector

CNR1 Communications Networking Riser slot

CPU1 Socket A for AMD Athlon processor

CPUFAN1 Cooling fan for CPU

DIMM1 ~ DIMM2 Two 184-pin DIMM sockets

FDD1 Floppy disk drive connector

FIDJP1 CPU ratio selector

IDE 1 Primary IDE channel

IDE 2 Secondary IDE channel

J3* Serial IRQ header

J5 IEEE 1394A header

J6 IEEE 1394A header

JP1 Clear CMOS jumper

JP3 BIOS protection jumper

LED11Memory module LED

PANEL1 Connector for case front panel switches and LED indica-

tors

PCI1 ~ PCI3 Three 32-bit add-in card slots

SIR1 Serial infrared cable header

SJ1Single-color LED header

SPDIF1* SPDIF out header

SPKR1 Speaker connector

USB2/3 Front panel USB headers

WOL1 Wake On LAN wakeup connector

WOM1 Wake On Modem wakeup connector

* Reserved for OEM use only

This concludes Chapter 1. The next chapter explains how to install the main-

board.

1The red indicator LED1 turns on if your system is still powered, at which time

memory modules cannot be installed or uninstalled.

Inhaltsverzeichnis

Andere ECS Hauptplatine Handbücher

ECS

ECS A880GM-M7 Bedienungsanleitung

ECS

ECS H61H-G11 Bedienungsanleitung

ECS

ECS 865GV-M3 Series Bedienungsanleitung

ECS

ECS P4VMM2 Bedienungsanleitung

ECS

ECS B85H3-M9 Bedienungsanleitung

ECS

ECS L7VMM2 Bedienungsanleitung

ECS

ECS 649-M2 Bedienungsanleitung

ECS

ECS B75H2-M3 Bedienungsanleitung

ECS

ECS H110T-SI01 Bedienungsanleitung

ECS

ECS Photon Extreme KN3 SLI2 Bedienungsanleitung

ECS

ECS A740GM-M Bedienungsanleitung

ECS

ECS GF7100PVT-M3 Bedienungsanleitung

ECS

ECS 848P-A7 Bedienungsanleitung

ECS

ECS A75F2-M2 Bedienungsanleitung

ECS

ECS Motherboard Bedienungsanleitung

ECS

ECS Z270-LIGHTSABER Bedienungsanleitung

ECS

ECS A75F2-A2 V1.0 Bedienungsanleitung

ECS

ECS H61H2-M9 Bedienungsanleitung

ECS

ECS 945GCT-M/1333 Bedienungsanleitung

ECS

ECS A780LM-M Bedienungsanleitung

ECS

ECS H67H2-M Bedienungsanleitung

ECS

ECS 946GZT-M2 Bedienungsanleitung

ECS

ECS P4VXMS Bedienungsanleitung

ECS

ECS P4M890T-M2 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung