Eddyfi Technologies M2M MANTIS Leitfaden
1
© 2020 Eddyfi Technologies
TECHNICAL DOCUMENTATION |
M2M MANTIS
Revision C.3
Redacted by Thierry COUTURIER
Approved by Fabien DURAND
Date : 25/07/2020
2
SUMMARY
1. MECHANICAL DRAWING
2. PHASED ARRAY CONNECTOR
3. UT CONNECTOR
4. ENCODER CONNECTOR
5. POWER CONNECTOR
6. BATTERY SLOT
7. FRONT PANEL
8. I/O CONNECTORS
9. ACCESSORIES
10. GLOBAL WARNING
11. BATTERY WARNING
12. CLEANING
13. TECHNICAL SPECIFICATIONS
3
1. MECHANICAL DRAWING
4
IPEX Connector Location
• For Phased-array probe with IPEX connector
• For probe splitters or probe adaptors
• Compatible with IPEX easy-latch adaptor frame:
• IMP_0061-EASYLATCH-ADAPT
Connector Utility
Connector Information
Supplier: I-PEX
Reference: 30046-160T-F
Matching Connector
Supplier: I-PEX
References:
- straight: 30056-160T-F
- right angle: 30047-160T-04F
For electric safety reasons, only accessories approved
by Eddyfi Technologies can be used. Before purchasing
any probe, please contact us.
2. PHASED ARRAY CONNECTOR
5
Connector Mapping
Signal Name Description User matching signal
ER1 to ER64 Phased-array channel
number 1 to 64 Phased-array probe channel 1 to 64
GND Ground pin
For better ultrasound result, all GND
pin have to be connected to probe
ground.
Connector Signal Description
2. PHASED ARRAY CONNECTOR
6
Connectors Location Connector Utility
Connector MappingConnector Information
Supplier: LEMO
Reference: ERN.00.250.CTL
Matching Connector
• UT connector is NimCAMAC standard.
• Supplier: LEMO
• Reference: FGG.00.302.CLAD35
3. UT CONNECTORS
For electric safety reasons, only accessories approved by EDDYFI can be used. Before purchasing
any probe, please contact us.
On MANTIS, there is one UT channel that can be used:
• in Pitch/Catch mode.
• P/R: Pulser
• R: Receiver
• in Pulse/Echo mode.
• P/R: Pulser / Receiver
• R: not connected
7
Connector Location
4. ENCODER CONNECTOR
Connector Information
Supplier: Connector type LEMO EGG
Reference: EGG.1K.316.CLL
Matching Cable
Supplier: LEMO (Connector Male 16 Pin)
Reference: FGG.1K.316.CLAC65Z
CONNECT UP TO 3 DIFFERENT ENCODERS
- +5V TTL inputs
- quadrature mode or clock/dir mode
Number of available encoders : 2 or 3 depending on
software setup and option.
•INPUTS/OUTPUTS :
- 2 TTL inputs
Connector Utility
8
Connector Mapping
4. ENCODER CONNECTOR
5V
Encoder
input
Buffer
470Ω
Operation Encoder
Front View of the Connector
Signal Name Description User matching signal
Encoder Phase A/B TTL 5V -Absolute Max current -50 mA
-Max frequency = 4 MHz
9
Connector Signal Description 2/3
4. ENCODER CONNECTOR
Signal Name Description User matching signal
Synchro1
Synchro1 Input/Output
TTL 5V
-If configured as OUTPUT (see in Capture software as below,
Type ≠ “1-axis encoder +increment”)
-TTL 5V
-= PRF = 5V/100ns pulse generated with each Pulser signal (IPEX
connector).
-Signal can be used to synchronize an external system
-Jitter = 10ns.
-Absolute Max output current +/-50 mA
-If configured as INPUT (see in Capture software as below,
Type = “1-axis encoder +increment”)
-TTL 5V, active on High level
-Max Input current 50µA
-When connected to Phased Array Wheel probe, Synchro1 is used as
« Index Increment » (short press) and « Scan Encoder Reset » (long
press > 2sec).
100 KΩ
10
Connector Signal Description 3/3
4. ENCODER CONNECTOR
Signal Name Description User matching signal
Synchro2
Synchro2 Input/Output
TTL 5V
-If configured as OUTPUT (see in Capture software as below,
Type ≠ “1-axis encoder +increment”)
-TTL 5V
-= PRF = 5V/100ns pulse generated with each Pulser signal (IPEX
connector).
-Signal can be used to synchronize an external system
-Jitter = 10ns.
-Absolute Max output current +/-50 mA
-If configured as INPUT (see in Capture software as below,
Type = “1-axis encoder +increment”)
-TTL 5V, active on High level
-Max Input current 50µA
-When connected to Phased Array Wheel probe, Synchro2 is used as
« Pause/Resume » to toggle Pause/Resume.
100 KΩ
Andere Handbücher für M2M MANTIS
2
Inhaltsverzeichnis
Andere Eddyfi Technologies Messgerät Handbücher
