Edelbrock 5253 Bedienungsanleitung

Rev. 9/07 - DA/mc

Catalog #5253

Brochure #63-0456

Page 1 of 2

Edelbrock Adjustable Trailing Arm

for 2005-2008 Ford Mustang

Catalog #5253

Installation Instructions

Please study these instructions carefully before installing your new Adjustable Trailing Arm. If you have any questions,

contact our Technical Hotline at: 1-800-416-8628, 7 am to 5 pm, Monday-Friday, Pacific Standard Time or

e-mail us at [email protected].

Tools and Supplies Required:

❑ Floorjack ❑18mm socket, combination wrench, and torque wrench

❑Jackstands ❑Blue Loctite™

❑Tire chocks ❑Grease gun

❑Lug wrench

REMOVAL OF STOCK TRAILING ARMS

1. Place car on level surface and place tire chocks in front of and behind front tires.

2. Support rear of the car on jackstands and remove the rear wheels.

3. Place a floorjack under the differential and lift up slightly to remove tension from the trailing arm bolts - make sure

not to lift the car off the jackstands

(Figure 1).

KEEP FLOORJACK UNDER CAR DURING THE COMPLETE REMOVAL AND INSTALLATION PROCEDURE.

4. Remove bolts retaining trailing arm support bracket.

NOTE: Two bolts can be reached from the undercar, the

third bolt is accessed under rear seat. Rear seat lower

cushion is retained by two clips at the front of the cushion.

5. Unbolt front trailing arm bolt from support bracket.

6. Clean frame at trailing arm pivot area with a wire brush.

Fig. 1

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may

result in poor performance and engine or vehicle damage.

Rev. 9/07 - DA/mc

Catalog #5253

Brochure #63-0456

Page 2 of 2

Edelbrock Adjustable Trailing Arm is fully assembled, greased, and ready to install.

1. Install Edelbrock adjustable trailing arm into trailing arm support bracket using supplied spacers. Spacers have a lip

on them that goes into heim joint. Install OEM bolt in the same direction as the factory. Use blue Loctite™ and torque

bolt to 90 ft./lb.

2. Re-install trailing arm support bracket and trailing arm in vehicle. Use blue Loctite™ on threads and torque to

70 ft. /lb.

3. The trailing arm should then pivot smoothly.

4. Pivot trailing arm into position over OE bushing. Install rear bolt in same direction as original.

5. Place one drop of blue Loctite™ on clean threads and torque the nut to 90 ft./lbs.

6. Although Edelbrock Trailing Arm is pre-lubed, you may want to finish your installation by lubing the front bushings with

a greasegun. Be sure to replace the dust caps on the Zerk fittings to prevent dirt and corrosion from damaging the

fitting.

Check all nut and bolt tightness after first 10 miles.

NOTES:

1. Edelbrock Adjustable Trailing arms come pre-adjusted to stock length. Pinion angle can be adjusted by loosening the

jam nuts on the arms and turning the aluminum adjuster sleeve in the center of the arm. Both arms should be

adjusted evenly. A properly installed and adjusted trailing arm will have the spherical ball straight and parallel with

the ball housing. If the ball is twisted in its housing when installed, the arm could fail during suspension articulation.

After adjustment has been made, use a drop of Loctite™ on threads at jam nuts.

2. Jam nuts should be checked periodically for tightness.

3. To further enhance the handling and performance of your Mustang, check our catalog to find out more about Edelbrock

Suspension components such as coil springs, lower trailing arms, strut tower brace, panhard rod, and sub-frame

connectors. To order our catalog, call 1-800-FUN-TEAM.

Edelbrock Corporation, 2700 California St., Torrance, CA 90503

Tech Line: 1-800-416-8628

E-Mail: [email protected]

INSTALLATION INSTRUCTIONS

Inhaltsverzeichnis

Andere Edelbrock Automobilteil Handbücher

Edelbrock

Edelbrock Russell R08364 Bedienungsanleitung

Edelbrock

Edelbrock 73802 Bedienungsanleitung

Edelbrock

Edelbrock 5291 Bedienungsanleitung

Edelbrock

Edelbrock 67082 Bedienungsanleitung

Edelbrock

Edelbrock Predator Carburetor Betriebsanleitung

Edelbrock

Edelbrock 5260 Bedienungsanleitung

Edelbrock

Edelbrock 72230 Bedienungsanleitung

Edelbrock

Edelbrock 6607 Bedienungsanleitung

Edelbrock

Edelbrock 1483 Bedienungsanleitung

Edelbrock

Edelbrock 7122 Bedienungsanleitung

Edelbrock

Edelbrock Performer 1403 Bedienungsanleitung

Edelbrock

Edelbrock Performer RPM 7167 Bedienungsanleitung

Edelbrock

Edelbrock 4794 Bedienungsanleitung

Edelbrock

Edelbrock 63-0144 Bedienungsanleitung

Edelbrock

Edelbrock 29085 Bedienungsanleitung

Edelbrock

Edelbrock 70050 Bedienungsanleitung

Edelbrock

Edelbrock Honda TRX450R Betriebsanleitung

Edelbrock

Edelbrock Quiet-Flo 1791 Bedienungsanleitung

Edelbrock

Edelbrock 71852 Bedienungsanleitung

Edelbrock

Edelbrock 5420 Bedienungsanleitung

Edelbrock

Edelbrock 5769 Bedienungsanleitung

Edelbrock

Edelbrock 1500-6500 Bedienungsanleitung

Edelbrock

Edelbrock 65012 Bedienungsanleitung

Edelbrock

Edelbrock 70003 Bedienungsanleitung

Beliebte Automobilteil Handbücher anderer Marken

Dakota Digital

Dakota Digital 650277 Bedienungsanleitung

bosal

bosal 037031 Bedienungsanleitung

Vintage Air

Vintage Air 571063 Bedienungsanleitung

GFB

GFB EX38 Bedienungsanleitung

bosal

bosal 028091 Bedienungsanleitung

Dodge

Dodge 8W-43 Kurzanleitung

ICI

ICI Magnum FBM10DGN Bedienungsanleitung

Volant Perfomance

Volant Perfomance 19435 Bedienungsanleitung

BENDIX

BENDIX GEN 4 GEN 5 ABS Bedienungsanleitung

Vintage Air

Vintage Air 571065 Bedienungsanleitung

Rugged Ridge

Rugged Ridge 11503.13 Bedienungsanleitung

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Bedienungsanleitung

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Leitfaden

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Bedienungsanleitung

Toshiba

Toshiba 48-1250 A Bedienungsanleitung

aldes

aldes EHT2 Bedienungsanleitung

Go Rhino

Go Rhino 24371T Bedienungsanleitung

BBK

BBK 18950 Bedienungsanleitung