Edwards Signaling XTRA-BRITE 48XBRMA240 Bedienungsanleitung

Description

The Catalog Series 48XBRM Visual Indicator is a UL and cUL

Listed signaling appliance rated for NEMA 4X applications.

The signals are suitable for indoor or outdoor (weatherproof)

installation and are available in AC and DC models as listed

above.

The 48XBRM Series XBR (XTRA-BRITETM) LED Dual-Mode

signals are well suited in high ambient noise level areas,

especially where ear protection must be worn. These LED

beacons are also ideal for high-vibration applications and

areas where long lamp life is advantageous. 48XBRM LED

beacons ship from the factory in steady-on mode and can

be readily transformed by changing the dipswitch setting to

65 FPM ashing mode.

The 48XBRM series signals can be mounted on 1/2" (13mm)

NPT conduit (indoor or outdoor) or direct surface mounted

(indoor only). For outdoor (weatherproof) installation, the

signals must be mounted with their lens dome facing directly

up. When installing indoors, these signals can be mounted

in any position.

Electrical Specications

Installation Instructions for 48XBRM Series

XBR (XTRA-BRITETM) LED DUAL-MODE Visual

Indicator

Installation

To prevent electrical shock, ensure that power

is disconnected before installing the signals.

Install in accordance with the latest edition of the National

Electrical Code and local regulations. Install the signals

using one of the following applicable mounting procedures.

Conduit Mounting (Indoor or Outdoor) - Figure 1

WARNING

To prevent leakage and a potential shock

hazard, when mounting outdoors the signal

must be installed with the lens or dome facing

directly up.

WARNING

1. Insert a small at blade screwdriver between the locking

mechanism and the lens. Gently push down and then

pry up, unseating the lens. Pull the lens up and off of

the signal mounting base, being careful not to damage

the internal circuit.

2. Setting the Flash Pattern: The 48XBRM Series Visual

Indicator is a dual-mode device supplied with a default

setting of steady-on. If ashing (65 fpm) mode is desired,

set dipswitch as shown in Figure 4. Refer to Figure 3 for

dipswitch location.

3. After setting the ash pattern, carefully place the lens

back on the unit and snap in place.

4. Route the signal's wire leads through 1/2" NPT conduit

(not supplied) and thread the conduit into the signal

mounting base.

5. Connect the eld wiring to the signal wire leads as

described in the Wiring Section.

P/N 3101569 ISSUE 3

Catalog Number Electrical Specs Color

48XBRMA24D 24V DC, 0.215A Amber

48XBRMA120A 120V AC*, 0.108A Amber

48XBRMB24D 24V DC, 0.215A Blue

48XBRMB120A 120V AC*, 0.108A Blue

48XBRMG24D 24V DC, 0.215A Green

48XBRMG120A 120V AC*, 0.108A Green

48XBRMR24D 24V DC, 0.215A Red

48XBRMR120A 120V AC*, 0.108A Red

48XBRMW24D 24V DC, 0.215A White

48XBRMW120A 120V AC*, 0.108A White

*120V AC 50/60 Hz

Mechanical Specications

Outdoor Locations

Temperature Ratings ........... -31F to +150F (-35C to +66C)

PLC Compatibility

Signaling devices may be directly connected to PLC output

cards that meet the electrical input load specications listed

in Table 1. When signaling device ash rates are to be con-

trolled via PLC, dip switch settings should be left in "steady-

on" mode as originally shipped from the factory.

P/N 3101569 ISSUE 3

Figure 2. Direct Surface Mounting of the

48XBRM Series Signals

NOTE: Enclose wiring within an approved

raceway interconnecting the appliance

and junction box in accordance with

governing codes, standards and

regulations.

Direct Surface Mounting (Indoor Only) - Figure 2

NOTE: The installer should use suitable hardware

appropriate for the installation.

1. Insert a small at blade screwdriver between the locking

mechanism and the lens. Gently push down and then

pry up, unseating the lens. Pull the lens up and off of

the signal mounting base, being careful not to damage

the internal circuit.

2. Setting the Flash Pattern: The 48XBRM Series Visual

Indicator is supplied with a default setting of steady-on.

If ashing (65 fpm) is desired, set dipswitch as shown in

Figure 4.

3. Remove the two knockouts for mounting screws from

the signal base. Place the 3-3/4" (95mm) mounting

gasket provided in the direct surface mounting kit on

the mounting surface and mark the center of the three

holes in the gasket on the mounting surface. Remove

the gasket and drill a 3/8" (10mm) hole at each of the

marked positions.

4. Install the two rubber expansion plugs provided in the

hardware kit into the two outer holes in the mounting

surface.

5. Route the wire leads from the signal base through the

center hole in both the mounting gasket and surface. The

wiring should be run through an approved raceway or

conduit connected between the bottom of the signal base

and an approved junction box (not supplied). Bring wire

leads into the junction box. Refer to the signal's label for

voltage rating.

6. Align the outer holes in the mounting gasket with the

holes in the surface. Insert two screws with lockwashers

through the two outer holes in the signal base and align

the screws with the rubber expansion plugs as shown

in Figure 2. Press the signal base rmly against the

mounting surface and tighten the screws.

7. Carefully place the lens back on the unit and snap in

place.

8. Connect the eld wiring to the signal wire leads as

described in the Wiring Section.

Wiring

1. For AC models, use wire nuts (not supplied) and connect

the signal's black and white wire leads to the power

source wires. Polarity is not important.

2. For DC models, connect the signal's red wire to the

positive power source wire and connect the signal's black

wire to the negative power source using appropriate

connectors (not supplied). Polarity must be observed.

Mounting base

and support plate

Top view of

mounting base

One of two

knockouts for

direct surface

mounting

Enclose in

raceway

To field

wiring

Mounting surface

(2) Mounting

screws (supplied

with DC models)

(2) Lockwashers

(supplied with

DC models))

Mounting gasket

(supplied with

DC models)

(2) Rubber expansion

plugs (supplied with

DC models)

Figure 1. Conduit Mounting

Lens

Mounting and

lamp support plate

1/2” (13 mm) NPT

conduit

(not supplied)

Locking

Mechanism

18” Wire Leads

DC units; Red Positive (+),

AC units; Black Hot

DC units; Black Negative (-),

AC units; White Neutral

Power source

Wires

P/N 3101569 ISSUE 3

Replacement Parts

Component Catalog Number

Lens* - 48XBRM Series 96-L(*)

*Specify color of lens by adding one of the following letters to the catalog number: A-amber,

B-blue, G-green, or R-red, C - clear (used with white LEDs). Example: A red lens for the 48XBR

series signal is 96-LR.

Maintenance

Cleaning

Periodically clean the lens surface with a soft cloth or sponge

and water or a mild detergent solution to maintain optimum

light visibility. Ensure that the lens is completely dry before

assembling the signal.

To prevent damage to the lens, do not use

abrasive materials or cleaners.

CAUTION

Figure 4. Flash Pattern Dipswitch Settings

STEADY

(FACTORY

DEFAULT)

OFF

STEADY

65 FPM

Table 1. PLC Compatibility

Operating Maximum off state Continuous on Surge (inrush/duration)

Cat. No. voltage* leakage current (mA) current (mA) (A/µs**)

48XBRM( )24D 24V DC 5 215 34.5/52

48XBRM( )120A 120V AC 5 108 37.5/164

*All AC volts at 50/60 Hz

**Amps/microseconds

LED Light

Source

Flash Pattern

Dipswitch

Base

Figure 3. Dipswitch Location

Dieses Handbuch passt für folgende Modelle

Andere Edwards Signaling Messgerät Handbücher

Edwards Signaling

Edwards Signaling FSRZI-A Montageanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung