Edwards SIGA-CC2 Montageanleitung

SIGA-CC2 Dual Input Signal Module

Installation Sheet

Description

The SIGA-CC2 Dual Input Signal Module is an addressable

device that connects one of two risers to a Class B supervised

output circuit.

When activated, the module connects the output circuit to the

Riser 1 or Riser 2 input. The input can be either 24 VDC (to

operate polarized audible and visible signal notification

appliances), or 25 or 70 VRMS (to operate audio evacuation

speakers). Typically, the Riser 1 input connects to the ALERT

channel and the Riser 2 input connects to the EVAC channel.

The module does not provide signal synchronization. To meet

UL 864 requirements for horn and strobe signal

synchronization, you must install a Genesis Signal Master

module. This module does not provide supervision of the riser;

the fire alarm panel provides this function.

The SIGA-CC2 module requires two addresses on the

signaling line circuit (SLC). Addresses are assigned

electronically. There are no address switches.

Diagnostic LEDs provide visible indication of the state of the

module through the cover plate:

•Normal: Green LED flashes

•Alarm/active: Red LED flashes

Personality codes

Use the personality codes described below to configure the

SIGA-CC2 module. See Table 1 for listing information.

Table 1: Personality codes

Code

Description

UL 864

CAN/ULC-

S527

EN 54-18

Riser selector -

supervised output

(Class B)



Personality code 7: Riser selector - supervised output

(Class B). Configures the SIGA-CC2 module as a

one - or two - input, signal power (24 VDC) or audio evacuation

(25 or 70 VRMS) riser selector. The output circuit is monitored

for open or shorted wiring. If a short exists, the control panel

inhibits the activation of the signal circuit, so the riser is not

connected to the wiring fault.

Installation

Install this device in accordance with applicable national and

local codes, ordinances, and regulations.

Notes

•The module is shipped from the factory as an assembled

unit; it contains no user-serviceable parts and should not

be disassembled.

•This module does not operate without electrical power. As

fires frequently cause power interruption, discuss further

safeguards with the local fire protection specialist.

To install the module:

1. Write the address assigned to the module on the label

provided, and then apply the label to the module. Remove

the serial number label from the module, and then attach it

to the project documentation.

2. Wire in accordance with “Wiring” on page 2.

3. Using the self-tapping screw provided, attach the wall

plate to the module. See Figure 1.

4. Using the four machine screws, attach the wall plate and

module to the electrical box.

2 / 5 P/N 387040P-EN • REV 013 • ISS 20SEP17

Figure 1: Installing the SIGA-CC2 module

(1) Compatible electrical box

(3) SIGA-CC2 module

(3) Wall plate

(5) #6-32 × 5/8 machine screw

(4X)

(6) #4 × 1/2 self-tapping screw

Protection from transient spikes

For installations in which the output circuit connects to

electromechanical bells or horns, install a bipolar transient

protector (P/N 235196P) to protect the module from transient

spikes caused by switching inductive loads. Locate bells and

horns at least 6 ft. (1.8 m) from the module.

To install a bipolar transient protector:

1. Install the transient protector across the output circuit

inside the electrical box with the module. See Figure 2.

Figure 2: Bell circuit showing bipolar transient protector

placement

(1) Normal state

(2) Active state

Wiring

Wire this device in accordance with applicable national and

local codes, ordinances, and regulations.

General wiring notes

•Refer to the Signature loop controller installation sheet for

SLC wiring specifications.

•Each terminal on the module is limited to a single

conductor.

•Test resistors are supplied with the SIGA-CC2 to prevent

trouble signals on unused circuits during installation.

When connecting field wires, remove the test resistors and

install a UL/ULC Listed 47 kΩEOLR at the end of the

circuit.

•The module does not support conventional smoke

detectors.

Riser wiring notes

•For maximum line impedance, refer to the installation

manual for the fire alarm panel. Maximum circuit

capacitance is 0.1 µF.

•If the riser is used for more than one notification zone,

install in accordance with the survivability from attack by

fire requirements in NFPA 72 National Fire Alarm and

Signaling Code.

•The SIGA-CC2 module does not supervise the riser; the

fire alarm control panel provides this function.

To wire the module:

1. Verify that all field wiring is free of opens, shorts, and

ground faults.

2. Strip 1/4 in. (about 6 mm) from the ends of all wires that

connect to the terminal block of the module.

When stripping wire ends, exposing more wire may cause

a ground fault; exposing less wire may result in a faulty

connection.

3. Connect the field wires. See Figure 3 and Figure 4.

(1)

(2) (3)

(4)

(5)

10 9

(1) (2)

P/N 387040P-EN • REV 013 • ISS 20SEP17 3 / 5

Figure 3: Wiring diagram for NAC

(1) Signal polarity is shown when the circuit is in supervisory state.

Polarity reverses when the circuit is active.

(2) Supervised.

(3) Power-limited unless connected to a nonpower-limited source. If

the source is nonpower-limited, eliminate the power-limited mark

and maintain a minimum of 0.25 in. (6.4 mm) space from power-

limited wiring. For other mounting methods, see enclosure and

bracket installation sheets to maintain separation of power-

limited and nonpower-limited wiring. The wire size must be

capable of handling fault current from nonpower-limited source.

—or —

Use type FPL, FPLR, FPLP, or permitted substitute cables,

provided these power-limited cable conductors extending beyond

the jacket are separated by a minimum of 0.25 in. (6.4 mm)

space or by a nonconductive sleeve or nonconductive barrier

from all other conductors. Refer to the NFPA 70 National

Electrical Code for more details.

(4) If using a G1-P Genesis series horn while connected to a

compatible fire alarm control panel, a CDR-3 Bell Coder must

be used to comply with NFPA 72 standard alarm evacuation

signal.

(5) 47 kΩ EOLR (P/N EOL-47).

(6) Signaling line circuit (SLC) to next device.

(7) Channel 1 (ALERT) AUX riser to next module or riser

supervisory device.

(8) Power-limited regulated, power supply UL/ULC Listed for fire

protective signaling systems.

(9) Channel 1 (ALERT) AUX riser from previous device.

(10) Signaling line circuit (SLC) from previous device. Supervised

and power-limited.

(11) Channel 2 (EVAC) AUX riser from previous device.

(12) Channel 2 (EVAC) AUX riser to next module or riser

supervisory device.

(5)

(1)(2)(3)(4)

(6)

(7)

(9)

(10)

(11) +(12)

4 / 5 P/N 387040P-EN • REV 013 • ISS 20SEP17

Figure 4: Wiring diagram for audio

(1) Signal polarity is shown when the circuit is in supervisory state.

Polarity reverses when the circuit is active.

(2) Supervised.

(3) Power-limited unless connected to a nonpower-limited source. If

the source is nonpower-limited, eliminate the power-limited mark

and maintain a minimum of 0.25 in. (6.4 mm) space from power-

limited wiring. For other mounting methods, see enclosure and

bracket installation sheets to maintain separation of power-

limited and nonpower-limited wiring. The wire size must be

capable of handling fault current from nonpower-limited source.

—or —

Use type FPL, FPLR, FPLP, or permitted substitute cables,

provided these power-limited cable conductors extending beyond

the jacket are separated by a minimum of 0.25 in. (6.4 mm)

space or by a nonconductive sleeve or nonconductive barrier

from all other conductors. Refer to the NFPA 70 National

Electrical Code for more details.

(4) Unshielded twisted pair.

(5) 47 kΩ EOLR (P/N EOL-47).

(6) Signaling line circuit (SLC) to next device.

(7) Channel 1 (ALERT) audio riser to next module or supervisory

end of line device.

(8) Unshielded twisted pair. Use shielded twisted pair when

installed in the same conduit as with a telephone riser.

(9) Channel 1 (ALERT) audio riser from previous device.

(10) Signaling line circuit (SLC) from previous device. Supervised

and power-limited.

(11) Channel 2 (EVAC) audio riser from previous device.

(12) Channel 2 (EVAC) audio riser to next module or supervisory

end of line device.

(5)

(1)(2)(3)(4)

(6)

(7)

(9)

(10)

(11) +(12)

P/N 387040P-EN • REV 013 • ISS 20SEP17 5 / 5

Specifications

Operating voltage range

15.20 to 19.95 VDC

Current

Standby

Activated

310 µA

135 µA

Maximum line impedance

Refer to the control panel installation

manual

Ground fault impedance

10 kΩ

Output ratings

(special applications)

24 VDC

25 VRMS audio

70 VRMS audio

EOL resistor value

Circuit resistance

Circuit capacitance

2 A

50 W

35 W

47 kΩ, UL/ULC Listed

Refer to the control panel installation

manual

0.1 µF max.

UL/ULC Listed EOLR

47 kΩ (P/N EOL-47)

Circuit designation

Signaling line circuits

Notification line circuits

Class A, Style 6 or Class B, Style 4

Class B, Style Y

LPCB/CPR electrical box

Requirements

Minimum size W × H × D

Plastic box with cover plate, no gaps

or unused holes

3.5 × 3.5 × 1.5 in. (85 × 85 × 38 mm)

Compatible electrical boxes

2-1/2 in. (64 mm) deep dual-gang box;

4 in. square box

1-1/2 in. (38 mm) deep box with a

dual-gang cover

Wire size

12 to 18 AWG (1.0 to 4.0 mm²)

Operating environment

Temperature

Relative humidity

32 to 120°F (0 to 49°C)

0 to 93%, noncondensing

Storage temperature range

−4 to 140°F (−20 to 60°C)

Regulatory information

FCC compliance

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired operation.

North American

standards

CAN/ULC-S527, UL 864

EN 54

EN 54-18: 2005 Input/output devices

EU compliance

CPR certificates

0832-CPR-F0329

2002/96/EC (WEEE directive): Products marked

with this symbol cannot be disposed of as

unsorted municipal waste in the European Union.

For proper recycling, return this product to your

local supplier upon the purchase of equivalent

new equipment, or dispose of it at designated

collection points. For more information, see:

www.recyclethis.info.

Contact information

For contact information, see www.edwardsfiresafety.com.

Inhaltsverzeichnis

Andere Edwards Steuereinheit Handbücher

Edwards

Edwards SCU-350 Series Bedienungsanleitung

Edwards

Edwards SCU-750 Bedienungsanleitung

Edwards

Edwards D-397-54-000 Bedienungsanleitung

Edwards

Edwards GV Series Bedienungsanleitung

Edwards

Edwards QSB63 Bedienungsanleitung

Edwards

Edwards IPVA10EK Bedienungsanleitung

Edwards

Edwards LCPVEK Series Bedienungsanleitung

Edwards

Edwards GXS Bedienungsanleitung

Edwards

Edwards QSB63 Bedienungsanleitung

Edwards

Edwards SIGA-IM2 Montageanleitung

Edwards

Edwards Speedivalve SP5 Bedienungsanleitung

Edwards

Edwards PV16EKA Bedienungsanleitung

Edwards

Edwards CTM Montageanleitung

Edwards

Edwards D397-52-000 Bedienungsanleitung

Edwards

Edwards SCU-1601 Bedienungsanleitung

Edwards

Edwards LCPV16EKA Bedienungsanleitung

Edwards

Edwards 3-24R Montageanleitung

Edwards

Edwards IBV16MKS Bedienungsanleitung

Edwards

Edwards SIGA-CC2A Bedienungsanleitung

Edwards

Edwards PV10/16EK Bedienungsanleitung

Edwards

Edwards SCU-800 Bedienungsanleitung

Edwards

Edwards GSA-CC1 Montageanleitung

Edwards

Edwards PVEK Series Bedienungsanleitung

Edwards

Edwards IPVA10EK Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung