Edwards STP Series Bedienungsanleitung
MT-50E-101-A
Model name Voltage
STP-F2203 series 200 - 240 Va.c.
STP Series Turbomolecular Pumps
STP-F2203 Series
Pump Specific Information
Instruction Manual (B)
STP pump consists of the three-volumed Instruction Manuals.
Instruction Manual (A): STP pump generic Instruction Manual
Supplied with STP pump
Instruction Manual (B):
(This Instruction Manual)
STP pump specific information
Supplied with STP pump
Instruction Manual (C): STP control unit Instruction Manual
Supplied with STP control unit
Copyright 2008 Edwards Japan Limited. All rights reserved. Printed in Japan.
This page intentionally blank
The description of this product consists of the three-volumed Instruction Manuals. Read through each
Instruction Manual before operation.
The separate volume contents of each description are as follows:
Instruction Manual (A)
STP pump generic Instruction Manual:
•Introduction
•Installation of the STP pump
•Installation of the STP control unit
•Operation
•Safety functions
•Maintenance and inspection
•Storage and disposal
•Service, Spares and accessories
Instruction Manual (B)
STP Pump specific information:
•Technical data
•How to Secure the STP pump
•Temperature Management System （TMS）
Instruction Manual (C)
STP control unit Instruction Manual:
•Introduction
•Technical data
•Installation
•Operation
•Serial communication protocol
•STP-Link (except for SCU-750)
•Maintenance
•Storage, transportation and disposal
•Service, spares, and accessories
Keep the manuals in an easily accessible location.
STP-F2203 Series Turbomolecular Pump
July 08 i Issue 1-a
PAGE
i
CONTENTS
Section Title Page
1 TECHNICAL DATA 1
1.1 Applicable pump specifications 1
1.1.1 STP pump specifications 2
1.1.2 Condition for the water-cooling unit 3
1.2 External appearance of the STP pump 3
1.3 Label affixing positions 6
1.4 Accessories 7
2 HOW TO SECURE THE STP PUMP 9
2.1 When securing the inlet port with bolts 9
3 TEMPERATURE MANAGEMENT SYSTEM (TMS) 13
3.1 Configuration of the STP pump with the TMS 13
3.2 TMS Connection cable 14
3.3 TMS heater 15
3.4 TMS valve 15
3.5 TMS sensor cable 15
3.6 Installation of the TMS unit 16
3.6.1 Connecting the TMS connection cable to the STP control unit 16
3.6.2 Connecting the pump and cables 16
3.6.3 Connecting TMS connection cable to STP pump 16
3.7 Condition for the TMS unit 17
3.8 Accessories 17
STP-F2203 Series Turbomolecular Pump
July 08 ii Issue 1-a
PAGE
ii ILLUSTRATIONS
Figure Title Page
1 STP-F2203 series: VG250/ISO250F 4
2 STP-F2203 series (with TMS unit): VG250/ISO250F 5
3 Label affixing positions for the STP pump 6
4 Example of securing the STP pump
(when securing the inlet port with bolts) 10
5 Shape of reduced diameter shank bolts 11
6 Bolt position for securing the flange (ISO250F) 12
7 Configuration of the STP pump with the TMS 13
8 External view of TMS connection cable 14
9 TMS sensor cable 15
TABLES
Table Title Page
1 Tightening torque of bolt 9
2 Maximum torque predicted and recommended securing bolt
for inlet port flange 10
3 Shape of reduced diameter shank bolts 11
STP-F2203 Series Turbomolecular Pump
July 08 1 Issue 1-a
TECHNICAL DATA
1
1 TECHNICAL DATA
1.1 Applicable pump specifications
Model Name Specification Applicable Control unit*1
STP-F2203 series High-flow type SCU-1500/SCU-1400
*1 Applicable control unit: There are different performance specifications between SCU-1500 and SCU-1400.
Refer to Section 1.1.1, "STP pump specifications" for the differences.
Naming convention:
•"C" following a pump model name indicates a corrosion resistant*2 type (e.g. STP-F2203C).
•"CV" indicates an enhanced corrosion resistant type with TMS*3 (e.g. STP-F2203CV).
*2 Corrosion resistant: STP pump with anti-corrosive treatment.
*3 Temperature Management System: TMS unit (optional accessory) maintains the temperature at the base of the
turbomolecular pump by monitoring the temperature with the temperature sensor in the
base of the turbomolecular pump, and performing the TMS valve and base heater
ON/OFF control.
STP-F2203 Series Turbomolecular Pump
July 08 2 Issue 1-a
TECHNICAL DATA
PAG
E
2
1
1.1.1 STP pump specifications
The values shown below are typical. They are not guaranteed.
Item F2203 series
Inlet port flange VG250/ISO250FFlange size
Outlet port flange KF40
N2L/s 2200Pumping speed
H2L/s 1200
N2>108Compression ratio
H2>103
Ultimate pressure Pa (Torr) 10-6 (10-8) order [after baking]
Allowable backing pressure*1 Pa (Torr) 500 (4): Water cooling/TMS unit used
Flow rate of purge gas <N2> Pa·m3/s (SCCM) 3.4×10-2 to 8.4×10-2 (20 to 50)
Rated speed rpm 27,000
Backup rotational speed*2 rpm Approximately 6,000
Starting time*3 min 7: with SCU-1500
8: with SCU-1400
Stopping time*3 min 8: with SCU-1500
10: with SCU-1400
Noise dB <50 (at 27,000r pm)
Temperature Management System (TMS) Available
Baking temperature °C <120
Lubricating oil Not necessary
Installation position Free
Cooling method Water cooling
Recommended backing-pump L/min >1,300
Mass*4 kg 61
Ambient temperature range °C 0 to 40
Storage temperature range °C -25 to 55
Applicable Control unit SCU-1500/SCU-1400
*1 The pressure is applicable under conditions that N2or other similar gas is vacuumed and the backing-pump (pumping
speed: 1,300 L/min) is used. When the gas is exhausted intermittently, the gas more than the maximum gas flow-rate can be
exhausted. Consult Edwards about conditions.
*2 A backup rotational speed is the lowest rotational speed to which the magnetic bearing can be backed up at a power failure.
*3 Time varies depending on the control unit used.
STP-F2203 Series Turbomolecular Pump
July 08 3 Issue 1-a
TECHNICAL DATA
1
*4 Mass is a value of state that the only standard accessory was installed (except the optional accessory).
Maximum gas flow-rate *5
Condition Maximum gas flow-rate *5
TMS SCU-1500 SCU-1400
Gas
Yes/No Set point
Cooling water Purge gas N2
gas flow rate Pa･m3/s
(SCCM)
Pa･m3/s
(SCCM)
No - 10 (6000) 8.5 (5000)
N2
Yes 75°C 4.6 (2700) 4.6 (2700)
No - 4.7 (2800) 4.7 (2800)
Ar
Yes 75°C
Temperature:
5 to 25 °C
Flow rate:
2 L/min
3.4×10-2 to
8.4×10-2
(20 to 50)
1.4 (800) 1.4 (800)
*5 The maximum gas flow-rate is applicable under conditions that N2or Ar gas is vacuumed continuously and the backing
backing-pump (pumping speed: 6,500 L/min) is used. It is changed depending on condition. For example, when the gas is
exhausted intermittently, the gas more than the maximum gas flow-rate can be exhausted. In this case, contact Edwards.
1.1.2 Condition for the water-cooling unit
Item Specification
Port type Rc 1/4 (Female) *1
Flow rate L/min 2
Water temperature °C 5 to 25
Water pressure MPa (kgf/cm2) 0.3 (3)
*1 Standard type
1.2 External appearance of the STP pump
See the next page.
STP-F2203 Series Turbomolecular Pump
July 08 4 Issue 1-a
TECHNICAL DATA
PAG
E
4
1
φ207
φA
φ289
φ296
φ341
G
(3) I
F
Ａ
(8)
φ235
(4)
(6)
(7)
(5)
22.5ﾟ
C
154
(2)
(1)
E
D
90ﾟ
B
H
176
20
20ﾟ
20ﾟ
45ﾟ
45ﾟ
Figure 1 - STP-F2203 series: VG250/ISO250F
No. Item Description
1 Screw hole for legs 4-M16 depth 30
2 Screw hole of legs 4-M16 depth 32
3 Height of the purge port
4 Cooling water port 2-Rc*11/4
5 STP cable connector
6 Outlet port flange KF40
7 Purge port KF10
8 Viewed from arrow A
Inlet
port
flange
VG250 ISO250F
φA 350 335
B 18 20
C 431 457
D 414 440
E 406 432
F 372 398
G 138 164
H 295 321
I 376 402
*1 ISO
Andere Handbücher für STP Series
14
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Edwards Wasserpumpe Handbücher
Edwards
Edwards HT10 Bedienungsanleitung
Edwards
Edwards nEXT240 Bedienungsanleitung
Edwards
Edwards nXR60i Bedienungsanleitung
Edwards
Edwards STP-301 Series Bedienungsanleitung
Edwards
Edwards XDS35iCE Bedienungsanleitung
Edwards
Edwards E2M28 Bedienungsanleitung
Edwards
Edwards nEXT200200 Bedienungsanleitung
Edwards
Edwards EXS Series Bedienungsanleitung
Edwards
Edwards 10 Bedienungsanleitung
Edwards
Edwards nRVi Bedienungsanleitung
Edwards
Edwards RV3 Bedienungsanleitung
Edwards
Edwards GXS 160 Bedienungsanleitung
Edwards
Edwards STP Series Bedienungsanleitung
Edwards
Edwards STP Series Bedienungsanleitung
Edwards
Edwards nXL110i Bedienungsanleitung
Edwards
Edwards E2M175 Bedienungsanleitung
Edwards
Edwards Cryo-Cooled Diffstak CR63/150 Bedienungsanleitung
Edwards
Edwards XDS35iR Bedienungsanleitung
Edwards
Edwards STP Series Bedienungsanleitung
Edwards
Edwards XDS 5 Bedienungsanleitung
Beliebte Wasserpumpe Handbücher anderer Marken
Sykes AmeriPumps
Sykes AmeriPumps GP100M Fehlerbehebungshandbuch
DUROMAX
DUROMAX XP WX Series Bedienungsanleitung
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Bedienungsanleitung
Franklin Electric
Franklin Electric IPS Bedienungsanleitung
Xylem
Xylem e-1532 Series Bedienungsanleitung
Milton Roy
Milton Roy PRIMEROYAL Bedienungsanleitung