EemaX EX360T12 Bedienungsanleitung

EemaX

THREE PHASE THERMOSTATIC

ELECTRIC INSTANTANEOUS WATER HEATER

MODELS: EX360T12, EX480T12, EX720T12, EX960T12

(208 volts only)

INSTALLATION GUIDE AND OWNERS MANUAL

WARNING

BEFOREATTEMPTING INSTALLATION OF THIS UNIT OR MAKING ANY ADJUSTMENTS

TO THE UNITALWAYS BE SURE MAIN CIRCUIT BREAKER IS OFF TO PREVENT DANGER

OF SERIOUS ELECTRIC SHOCK.

MODEL :

SERIAL NO :

INSTALLATION DATE :

ELEMENT RESISTANCE: OHMS

SWITCHON FLOW RATE: GPM

OPERATING TEMPERATURE

MIN: MAX:

Eemax Inc., 353 ChristianStreet, Oxford, CT 06478

INSTALLER/ CONSUMER RESPONSIBILITIES

PLEASE TAKE THE TIME TO READ NOT ONLY THIS MANUAL BUT ALSO THE

WARRANTYCARD ENCLOSED. WARRANTYOF THIS HEATER WILLDEPEND ON PROPER

INSTALLATION, OPERATION, AND REQUIRED MAINTENANCE. THE WARRANTY SHALL BE

VOID IF THE DESIGN ORSTRUCTURE OF THE WATER HEATER HAS BEEN ALTERED IN

ANY WAYWHATSOEVER. THE MANUFACTURER OF THIS WATER HEATER WILLNOT BE

LIABLE FOR ANY DAMAGES BECAUSE OF FAILURE TO COMPLY WITH THE INSTALLATION

AND OPERATING INSTRUCTIONS OUTLINED ON THE FOLLOWING PAGES.

IF YOU REQUIRE ANY HELP OR HAVE ANY QUESTIONS RELATING TO THE

INSTALLATION OR PERFORMANCE OF THIS HEATER, PLEASE CALL OUR TECHNICAL

SERVICE DEPARTMENT TOLL-FREE: 1-800-543-6163

HAVE THE INFORMATION LISTED BELOW BEFORE BEFORE CALLING.

GENERAL

The Eemax “Three Phase Thermostatic” water heater is specificallydesignedto take in

cold or pre-heated water and heat it to temperatures suitablefor commercial washing,

sluicing or processing up to a maximum temperature of 180 F (82 deg. C). To obtain

optimum performance and energy savings, the unit should be located as near as possible

to the point of use. The unit must only be installedin a vertical position with the inlet

and outlet at the bottom. The power is activated by individualelectronicflow switches located

in each of the twelve heating modules. These will be damaged by excessive heat, do not solder

any pipes that are in contact with the heater.

Also ensure pipes are clear of installationdebris before fitting the heater, otherwise the flow

switches could jam in the “on” position.The unit must be connected to its own individualelectric

circuit protected by a suitably rated three pole breaker. The maximum voltage which can be

appliedacross any heating module is 208 volts.

WARNING

Improper installation,adjustment, alteration, service or maintenance can cause DEATH,

SERIOUS BODILY INJURY OR PROPERTY DAMAGE. Refer to this manual for

assistance or consult the local electric utility for further information.

The unit is suppliedwith 1-1/4” NPT pipe connections. Under no circumstances use a blow

torch on pipe which is connected to the heater (serious damage to the electronic flow

switch will result). Carefully use Teflon tape, ensuring no debris enter the heater. Do not

use pipe dope.

WARNING

Failureto ground the system may result in death or serious injury.

MOUNTING THE UNIT

1) The unit should be mounted as close to the point of use as possible.

2) This unit must only be mounted in the vertical positionwith the water fittings located at the

bottom of the unit. Mounting other than in the vertical position WILLcause element burn out.

3) The cold water inlet is on the right hand side and the hot water outlet is on the left hand side.

Under NO circumstances can these be reversed.

4) Leave a minimum of 8” above the unit for easy replacement of the elements.

5) The heater should be fixed to the wall using all six mounting holes of the backplate. Unit

weight is approximately 70 lbs. Use an appropriatefastener for this weight. For the unit to be

mounted against hollow walls, suggest using steel wall anchors, with the correct grip range

and #6-32 screw size minimum.

6) The unit should be installedin the plumbing system in such a way that there is no tendency

for the unit to be starved of water: for example: by an excessive draw-off of cold water just

before the unit.Also do not fit an unrestricted hot water draw-off point below the heater as

this will tend to empty the heater by siphoning.

NOTE

ALL MOUNTING AND PLUMBING MUST BE COMPLETE BEFORE YOU PROCEED

WITH ELECTRICAL HOOK-UP. TEST THE INSTALLATION

FOR LEAKS BEFORE CONNECTING THE ELECTRICAL SUPPLY.

Hazardous Locations - Nonincendive Type Installation

1) The unit is mounted in an approved NEMA4 Enclosure.

2) Non-incindivefor Class I, Division 2, GroupsA, B, C&D. Temperature class: T5 (212 °F)

3)As to installation,refer to the National Electrical Code and NFPA 70. For locationsC1, Div.2

refer to section 501-4 (wiring methods) and 501-10 (utilizationequipment) respectively.

Note: If ignitionatmosphere is <T5 class, or if other classifications are required, another method of

compliance would be “Purged and Pressurized”. This is the process of supplying anenclosure

with a protective gas at a sufficient flow and positivepressure to reduce the concentration of

any flammable gas or vapor initiallypresent to an acceptable level. For further information, see

ANSI/NFPA 496-1998, Purged and Pressurized Enclosures for Electrical Equipment.

1) The unit is suppliedwith NPTfittings., USE THESE; DO NOT USE PIPE DOPE AND DO

NOT SOLDER PIPE TO THE INLET OR OUTLET.

2) Take care to ensure that the pipes are correctly aligned with the inlet and outlet bosses in

order to avoid excessive stress on the heater manifold.

NOTE: When solderingpipe joints remove heater from the wall. Serious damage can occur

if any solderingis done while pipes are connected to the heater.

Run water through the supply pipe to remove all debris from the pipe before connectingthe

heater. Failure to do so could cause damage to the flow switch.

3) Install isolating valves (full flow ball valve type) on both inlet and outlet pipes. This allows

unit to be isolatedfor maintenance purposes. (see Fig. 1)

4) When all plumbing is complete, fully check the system for water leaks at all plumbing

connections. If leak is present take corrective action. Fully open both inlet and outlet

ball valves. Run all hot water outlets fed by this heater one at a time for a minute or two

until the water flow is continuous, free from ”gulping”and from all visibleair pockets.

PLUMBING HOOK-

NOTE

ALL MOUNTING AND PLUMBING MUST BE COMPLETE BEFORE YOU PROCEED

WITH ELECTRICAL HOOK-UP.

TEST THE INSTALLATION FOR LEAKS BEFORE CONNECTING THE

ELECTRICAL SUPPLY.

7 “

Hot outlet

1-1/4” NPT

fitting

DO NOT

SOLDER

Cold inlet

1-1/4” NPT

fitting

DO NOT

SOLDER

ELECTRICAL HOOK-UP

WARNING

HAZARD OF ELECTRICAL SHOCK! BEFORE BEGINNING ANY WORK ON THE

INSTALLATION, MAKE SURE THE ELECTRICAL SUPPLY TO THE HEATER IS TURNED

“OFF”. FAILURE TO DO THIS COULD RESULT IN DEATH, SERIOUS BODILY INJURY,

OR PROPERTY DAMAGE.

WARNING

WATER HEATERS EQUIPPED FOR ONE VOLTAGE ONLY: CHECK THE RATING PLATE

ON THE FRONT OF THE UNIT. DO NOT USE THIS WATER HEATER WITHANY VOLTAGE

OTHER THAN THE ONE SHOWN ON THE MODEL RATING PLATE. FAILURE TO DO SO

CAN RESULT IN DEATH, SERIOUS BODILY INJURY, OR PROPERTY DAMAGE. IF YOU

HAVE ANY QUESTIONS OR DOUBTS CONSULT YOUR ELECTRIC COMPANY.

This heater must have its own independent circuit using four wires; three live and one ground,

of the appropriaterating protected by the correctly rated three pole breaker

WARNING

FAILURE TO GROUND THE SYSTEM MAY RESULT IN DEATH OR SERIOUS INJURY

IMPORTANT

BEFORE SWITCHING “ON” THE POWERAT THE MAIN CIRCUIT BREAKER PANEL MAKE

SURE THAT THE HOT WATER CIRCUIT IS FREE OF AIR POCKETS OR PREMATURE

FAILURE OF THE ELEMENT WILLOCCUR. TO DO THIS OPEN ALL HOT WATER OUTLETS

ONE AT A TIME FOR A MINUTE OR TWO UNTIL THE WATER FLOW IS CONTINUOUSAND

FREE FROM “GULPING” AND FROM VISIBLE AIR POCKETS.

RATINGS OF “EX” THREE PHASE MODELS

MODEL MAX. OUTPUT CURRENT TEMPERATURE RISE (F)

@ 208V PER PHASE 7.5gpm 10gpm 12.5gpm 15gpm 17.5gpm 20gpm

EX 960 96 KW 267 87 66 52 44 37 33

EX 720 72 KW 200 66 49 39 33 28 25

EX 480 48 KW 133 44 33 26 22 19 16

EX 360 36 KW 100 33 25 20 16 14 12

THIS UNIT MUST NOT BE CONNECTED IN STAR CONFIGURATION

COMMISSIONING YOUR HEATER

IMPORTANT

Before switching “on” the power at the main circuit breaker panel make sure that the hot

water circuit is free of air pockets or premature failureof the heating element will occur.

To do this open all hot water faucets one at a time for a minute or two until the water flow

is continuous and free from “gulping”and from visibleair pockets.

1) Withinlet and outlet BALL VALVES fully open, turn on a hot water outlet.

2) Run for 1 minute.

3) Switch on electric supply at circuit breaker panel.

4) The power indicatorlights should now come on (see Fig. 1), pulsingat first.Allow 40

seconds for the lights to stay full on, the heater is now operating at full power.

NOTE: At this point water temperature may not be hot.

5) Using the OUTLET BALL VALVE slowly reduce water flow until desired temperature is

achieved at hot water outlet.

NOTE: The water temperature is regulated by the flow through the heater. The lower the

flow the higher the temperature and vice versa.

MINIMUM SETTING MAXIMUM SETTING

THE TEMPERATURE CONTROLLING

POTENTIOMETER IS A PRECISION

COMPONENT. ADJUST GENTLY AND

DO NOT TURN BEYOND THE MIN.

AND MAX. STOP POINTS

6) Now turn the temperature adjustment screw on the first module counter clockwise about

1/8 of a turn, wait for 10-15 seconds and see if the indicator light begins to pulse. If it does

not, turn another 1/8 of a turn, wait and again see if the lamp begins to pulse. Repeat until

the light is pulsing regularlywhich indicatesthat the temperature has stabilizedat the set

temperature. Repeat with remaining modules. Check that the outlet temperature is at

the desired temperature and that all twelve elements are pulsingequally.The thermostats

are now set and the water temperature will always be the same when the lights are pulsing.

7) Check performance of flow switch by opening and closing the faucet of the outlet valve a

few times.

THE POWER INDICATOR LIGHT SHOULD ONLY BE ON WHENWATER IS FLOWING

THROUGH THE UNIT. For expected temperature rise at various rates of flow see chart

8) It is possible that drawing off cold water at comparatively high rates of flow elsewhere in

the buildingat the same time that the heater is working, could cause premature element

failure. Care should be taken not to starve the unit of cold water. To prevent this from

happening, open fully the main valve on the cold supply to the buildingand throttle back

the control valves to the other cold water outlets.

9) Do not operate heater if there is a possibilitythat the water in the heater is frozen. Element

module housing failure could occur.

TROUBLESHOOTING

SYMPTOM: NO HEAT INDICATOR LIGHT OFF

1)ELECTRIC SUPPLY IS OFF

Turn on the main circuit breaker.

2)NO OR LOW WATER FLOW

Ensure that the minimum flow rate to switch on your heater is met,

for this figure refer to the front cover of this manual.

Also check that the inlet filter screen is clear from any debris.

3)WATER CONNECTIONS ARE REVERSED

Cold water inlet = right side, hot water outlet = left side.

4)ELEMENT BURNED OUT

TURN OFF THE MAIN BREAKER!

Using an ohmmeter test the resistance of the heating element

across the two threaded termination rods on top of the element.

See the front cover of this manual for the correct value.

If the resistance is much greater than the correct value, call

your supplierfor a replacement element.

SYMPTOM: NO HEAT OR LOW TEMPERATURE WITH

INDICATOR LIGHT ON

1)WATER FLOW TOO HIGH

Reduce the water flow by using an outlet ball valve. See page 5

for temperature rise at various flow rates.

2)INCORRECT POWER SUPPLY

Make sure that the unit is connected to the voltage supply specified

on the rating label on the the front cover of the unit and no other.

3)ELEMENT BURNED OUT

TURN OFF THE MAIN BREAKER!

Repeat the steps from paragraph 4 above.

4)THERMOSTATADJUSTMENT SCREW NOT TURNED UP

Turn the thermostat adjustment screw clockwise in small

increments until the indicator light remains on. Take care not to

force the screw past it’s stop position.

REQUIRED MAINTENANCE PROCEDURE

To Be Performed by Qualified Personnel

MONTHLY CHECKS

M1) Ensure main circuit breaker is on.

M2) Open outlet valve(s) to run water thru unit. Ensure that the

minimum flow rate to switch on your heater is met, for this

figure refer to the front cover of this manual.

M3) Check outlet temperature for desired setting.

QUATERLY CHECKS

Q1) Turn off main circuit breaker.

Q2) Remove front cover from heater.

Q3) Inspection of heater bodies and distributionmanifold for

water leaks.

Q4) Inspection of fuses (50 amp each)

Q5) Inspection of 12 heater elements (see page 10 for element ohms)

Q5) Inspection of coarse inlet filter screen is clear from any debris.

Q6) Turn on main circuit breaker (note: unit has live electrical)

Q7) Carefully perform steps M1 thru M3 with cover removed, observe

each module for an indicator light.

Q8) Turn off circuit breaker

Q9) Install front cover, then turn on main circuit breaker.

REPLACEMENT PARTS DIAGRAM

HEATER CORE ASSEMBLY (PLEASE SPECIFY 208 VOLTS ON ANY ORDERS)

FOR EX360 T12 PART# EX1440 14.4 Ohms

FOR EX480 T12 PART# EX1080 10.8 Ohms

FOR EX720 T12 PART# EX720 7.2 Ohms

FOR EX960 T12 PART# EX540 5.4 Ohms

THERMOSTATIC

PCB

PART#EX100F/cont

TRIAC

PART#EX18

Contactor part # EX256

(208 volts)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere EemaX Boiler Handbücher

EemaX

EemaX EX3512 Bedienungsanleitung

EemaX

EemaX EX190 TC Bedienungsanleitung

EemaX

EemaX EX320TDI Bedienungsanleitung

EemaX

EemaX Series THREE Montageanleitung

EemaX

EemaX EX320T3 Bedienungsanleitung

EemaX

EemaX EEM24008 Service-Handbuch

EemaX

EemaX AUTOBOOSTER Service-Handbuch

EemaX

EemaX SP2412 Bedienungsanleitung

EemaX

EemaX HA008240 Service-Handbuch

EemaX

EemaX EX190 P2 Bedienungsanleitung

EemaX

EemaX EMT1 Beilage

EemaX

EemaX EX230T2T Bedienungsanleitung

EemaX

EemaX LavAdvantage SPEX1812T Bedienungsanleitung

EemaX

EemaX HA018240 Bedienungsanleitung

EemaX

EemaX EX280T2T Bedienungsanleitung

EemaX

EemaX EX1080T12 Bedienungsanleitung

EemaX

EemaX EX35 Bedienungsanleitung

EemaX

EemaX 208 VAC Bedienungsanleitung

EemaX

EemaX LavAdvantage Bedienungsanleitung

EemaX

EemaX PA014240 Bedienungsanleitung

EemaX

EemaX FlowCo SPEX1812 Bedienungsanleitung

EemaX

EemaX LavAdvantage SPEX1812T Bedienungsanleitung

EemaX

EemaX EX120 T Bedienungsanleitung

EemaX

EemaX HotMAx HM013240 Service-Handbuch

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

Applimo

Applimo Edel AIR Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung