EINHELL GC-DP 1340 G Bedienungsanleitung

GC-DP 1340 G

Art.-Nr.: 41.707.42 I.-Nr.: 11029

DOriginalbetriebsanleitung

Schmutzwasserpumpe

GB Original operating instructions

Dirty Water Pump

FInstructions d’origine

Pompe eaux usées

IIstruzioni per l’uso originali

Pompa per acque reue

NL Originele handleiding

Vuilwaterpomp

EManual de instrucciones original

Bomba de agua sucia

PManual de instruções original

Bomba de água suja

HR/ Originalne upute za uporabu

BIH Pumpa za prljavu vodu

RS Originalna uputstva za upotrebu

Pumpa za prljavu vodu

GR Πρωτότυπες Οδηγίες χρήσης

Αντλια ακαθαρτου νερου

TR Orijinal Kullanma Talimat

Pis su pompasi

Anl_GC_DP_1340_G_SPK7.indb 1 21.08.2019 15:13:53

- 2 -

Anl_GC_DP_1340_G_SPK7.indb 2 21.08.2019 15:14:15

- 13 -

Danger! - Read the operating instructions to reduce the risk of inquiry

This equipment can be used by children of 8 years and older and by

people with limited physical, sensory or mental capacities or those

with no experience and knowledge if they are supervised or have re-

ceived instruction in how to use the equipment safely and understand

the dangers which result from such use. Children are not allowed to

play with the equipment. Unless supervised, children are not allowed

to clean the equipment and carry out user-level maintenance work.

Anl_GC_DP_1340_G_SPK7.indb 13 21.08.2019 15:14:22

- 14 -

Danger!

When using the equipment, a few safety pre-

cautions must be observed to avoid injuries and

damage. Please read the complete operating

instructions and safety regulations with due care.

Keep this manual in a safe place, so that the in-

formation is available at all times. If you give the

equipment to any other person, hand over these

operating instructions and safety regulations as

well. We cannot accept any liability for damage

or accidents which arise due to a failure to follow

these instructions and the safety instructions.

1. Safety regulations

Danger!

Read all safety regulations and instructions.

Any errors made in following the safety regula-

tions and instructions may result in an electric

shock, re and/or serious injury.

Keep all safety regulations and instructions

in a safe place for future use.

Danger!

The pump must be powered via an earth-

leakage circuit breaker (RCD) with a rated

fault current of no more than 30 mA (accor-

ding to VDE 0100 Part 702 and 738).

The equipment is not designed for use in

swimming pools and paddling pools of any

kind or other bodies of water in which people

or animals may be present during operation.

It is prohibited to operate the equipment if a

person or animal is in the danger area. Ask

your electrician!

Danger!

• Before you put the equipment into opera-

tion, arrange for a specialist to check that

the earthing, protective multiple earthing or

residual-current operated circuit-breaker cir-

cuit comply with the safety regulations of the

power supply company and work correctly.

• The electrical plug-in connections must be

protected from wet conditions.

• If there is a risk of flooding, place the plug-in

connections in an area which is safe from

flooding.

• Strictly avoid pumping aggressive liquids and

abrasive substances.

• Protect the equipment from frost.

• Protect the equipment from dry running.

• Take suitable measures to keep the equip-

ment out of the reach of children.

2. Layout and items supplied

2.1 Layout (Fig. 1)

1. Handle

2. Floating switch

3. Hose connection approx. 50.8 mm (2”)

4. Intake cage

5. Rope

2.2 Items supplied

Please check that the article is complete as

specied in the scope of delivery. If parts are

missing, please contact our service center or the

sales outlet where you made your purchase at

the latest within 5 working days after purchasing

the product and upon presentation of a valid bill

of purchase. Also, refer to the warranty table in

the service information at the end of the operating

instructions.

• Open the packaging and take out the equip-

ment with care.

• Remove the packaging material and any

packaging and/or transportation braces (if

available).

• Check to see if all items are supplied.

• Inspect the equipment and accessories for

transport damage.

• If possible, please keep the packaging until

the end of the guarantee period.

Danger!

The equipment and packaging material are

not toys. Do not let children play with plastic

bags, foils or small parts. There is a danger of

swallowing or suﬀocating!

• Dirty water pump

• Hose connection

• Rope

• Original operating instructions

Anl_GC_DP_1340_G_SPK7.indb 14 21.08.2019 15:14:22

- 15 -

3. Proper use

The equipment you have purchased is designed

to pump water with a maximum temperature of

35 °C.This equipment must never be used for

other liquids, especially not for engine fuels,

cleaning agents and other chemically-based

products!

The equipment can be used wherever you want to

move water, e.g. in the house, in the garden, and

for many other applications. It must not be used to

operate swimming pools!

If you want to use the equipment in bodies of wa-

ter with a natural, muddy bottom, place the equip-

ment in a slightly elevated position, e.g. on bricks.

The equipment is not designed for continuous

operation, e.g. as a circulating pump in a pond. In

this case the equipment’s anticipated life will be

greatly shortened because the equipment was

not designed for continuous loading.

The equipment is to be used only for its prescri-

bed purpose. Any other use is deemed to be a

case of misuse.The user / operator and not the

manufacturer will be liable for any damage or inju-

ries of any kind caused as a result of this.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial

applications. Our warranty will be voided if the

machine is used in commercial, trade or industrial

businesses or for equivalent purposes.

The water may be contaminated by escaping lub-

ricating oil/lubricant.

4. Technical data

Mains connection........................... 230 V ~ 50 Hz

Power rating............................................. 1300 W

Max. pumping rate .................................23000 l/h

Max. delivery head....................................... 10 m

Max. submersion depth.................................. 5 m

Max. water temperature ............................... 35°C

Hose connection........... approx. 59.6 mm (G2) IG

Max. size of foreign bodies:....................Ø 40 mm

Switching point height: ON.....max. approx. 70 cm

Switching point height: OFF ....min. approx. 20 cm

Protection type..............................................IPX8

5. Before starting the equipment

Before you connect the equipment to the mains

supply make sure that the data on the rating plate

are identical to the mains data.

5.1 Installation

The equipment can be installed either:

• Stationary with a rigid pipe line

• Stationary with a flexible hose line

Notice!

Before you use the pump, clarify any possible

special conditions which need to be fullled for

the installation!

For example, additional safety measures may be

needed if damage to property could result from a

power failure, soiling or a defective gasket.

Examples of such safety measures:

Pumps running in parallel on a separately protec-

ted power circuit, moisture sensors for switching

oﬀthe pumps, and similar safety arrangements.

Be sure to consult a professional plumber if you

have any doubt.

The maximum pumping rate is possible only with

the largest possible line diameter; if smaller hoses

or pipes are connected, the pumping rate will be

reduced. Flexible hoses must be fastened to the

hose connection with a hose clip (not included in

the scope of supply).

When installing, never hang the equipment by the

discharge line or by the power cable. The equip-

ment must be hung up with the provided carry

handle or it must rest on the bottom of the shaft.

To ensure that the equipment works properly, the

Anl_GC_DP_1340_G_SPK7.indb 15 21.08.2019 15:14:22

- 16 -

bottom of the shaft always must be free of sludge

and other accumulations of dirt. If the water level

is too low, the sludge in the shaft can quickly dry

out and hinder the equipment from starting. It is

necessary therefore to check the equipment regu-

larly (carry out trial start-ups).

The pump shaft should be large enough.

5.2 Mains connection

Danger!

The equipment you have purchased comes with

an earthing-pin plug. The equipment is designed

for connection to a socket outlet with earthing

contact for 230 V ~ 50 Hz. Make sure that the

socket-outlet is suﬃciently fused (at least 6 A)

and in good working order. Insert the power plug

in the socket-outlet and the equipment is ready

for operation.

6. Operation

You can put the equipment into operation after

you have thoroughly read the installation and ope-

rating instructions. Pay attention to the following

points:

• Make sure that the equipment is set up secu-

rely.

• Check that the discharge line is fitted correct-

ly.

• Make sure that the electrical connection is

230 V ~ 50 Hz.

• Check that the electrical socket-outlet is in

good working order.

• Make sure that no moisture or water can ever

reach the power connection.

• Make sure that the equipment does not run

d r y.

• To switch off the equipment, pull the power

plug out of the socket outlet.

Setting the On/Oﬀswitching point:

The ON/OFF switching point of the oating switch

can be adjusted by shifting the oating switch in

the oating switch notched holder (Fig. 2/Item 6).

• The floating switch must be fitted so that the

switching point height: ON and the switch

point height: OFF can be reached easily and

with little force. Check this by placing the

equipment in a container filled with water

and carefully raising and lowering the floating

switch with your hand.You can then see whe-

ther the equipment switches on and off.

• Make sure that the distance between the floa-

ting switch head and the cable holder is not

too smaller than 10 cm. If the distance is too

small, there is no guarantee that the equip-

ment will work correctly.

• When adjusting the floating switch, make

sure that the floating switch does not touch

the bottom before the equipment is switched

off. Important! Risk of dry running.

7. Replacing the power cable

Danger!

If the power cable for this equipment is damaged,

it must be replaced by the manufacturer or its

after-sales service or similarly trained personnel

to avoid danger.

8. Cleaning, maintenance and

ordering of spare parts

Danger!

• Unplug the power plug prior to any mainte-

nance work.

• For mobile applications, the equipment

should be cleaned with clear water after every

usage.

• For stationary installation, it is recommended

that you check the floating switch for proper

operation every three months.

• Use a water jet to remove any lint or fibrous

particles that may have become trapped in

the housing.

• Remove sludge from the shaft bottom and

clean the shaft walls every 3 months.

• Use clear water to remove deposits from the

floating switch.

8.1 Cleaning the paddle wheel

If a lot of deposits collect in the housing, the bot-

tom part of the equipment must be dismantled as

follows:

1. Disconnect the intake cage from the housing.

2. Clean the paddle wheel with clear water.

Important! Do not put down or rest the

equipment on the paddle wheel!

3. Assemble in reverse order.

8.2 Maintenance

There are no parts inside the equipment which

require additional maintenance.

Anl_GC_DP_1340_G_SPK7.indb 16 21.08.2019 15:14:23

- 17 -

8.3 Ordering replacement parts:

Please quote the following data when ordering

replacement parts:

• Type of machine

• Article number of the machine

• Identification number of the machine

• Replacement part number of the part required

For our latest prices and information please go to

www.isc-gmbh.info

9. Disposal and recycling

The equipment is supplied in packaging to pre-

vent it from being damaged in transit. The raw

materials in this packaging can be reused or

recycled.The equipment and its accessories are

made of various types of material, such as metal

and plastic. Never place defective equipment in

your household refuse.The equipment should

be taken to a suitable collection center for proper

disposal. If you do not know the whereabouts of

such a collection point, you should ask in your

local council oﬃces.

10. Storage

Store the equipment and accessories in a dark

and dry place at above freezing temperature.The

ideal storage temperature is between 5 and 30

°C. Store the electric tool in its original packaging.

Anl_GC_DP_1340_G_SPK7.indb 17 21.08.2019 15:14:23

- 18 -

11. Troubleshooting guide

Faults Cause Remedy

The equipment

does not start

- Power supply not connected

- Floating switch does trigger

- Check power supply

- Raise position of oating switch

The equipment

does not pump

- Intake sieve clogged

- Discharge hose kinked

- Clean intake sieve with water jet

- Unkink the hose

The equipment

does not cut out

- Floating switch cannot sink - Place equipment correctly on shaft

bottom

Insuﬃcient pumping

rate

- Intake sieve clogged

- Performance reduced due to heavi-

ly contaminated and abrasive water

impurities

- Clean intake sieve

- Clean equipment and replace wear

parts

The equipment swit-

ches oﬀafter briey

running

- Motor circuit-breaker switches the

equipment oﬀdue to excessive wa-

ter contamination

- Water temperature too high; motor

circuit-breaker switches the equip-

ment oﬀ

- Unplug power plug and clean

equipment and shaft

- Ensure that maximum permissible

water temperature (35 °C) is not

exceeded

Anl_GC_DP_1340_G_SPK7.indb 18 21.08.2019 15:14:23

- 19 -

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and

its implementation in national laws, old electric power tools have to be separated from other waste and

disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment

must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment.

The old equipment can be returned to a suitable collection point that will dispose of the equipment in

accordance with the national recycling and waste disposal regulations. This does not apply to any ac-

cessories or aids without electrical components supplied with the old equipment.

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers

accompanying products is permitted only with the express consent of the iSC GmbH.

Subject to technical changes

Anl_GC_DP_1340_G_SPK7.indb 19 21.08.2019 15:14:23

- 20 -

Service information

We have competent service partners in all countries named on the guarantee certicate whose contact

details can also be found on the guarantee certicate. These partners will help you with all service re-

quests such as repairs, spare and wearing part orders or the purchase of consumables.

Please note that the following parts of this product are subject to normal or natural wear and that the

following parts are therefore also required for use as consumables.

Category Example

Wear parts* Impeller

Consumables*

Missing parts

* Not necessarily included in the scope of delivery!

In the eﬀect of defects or faults, please register the problem on the internet at www.isc-gmbh.info. Ple-

ase ensure that you provide a precise description of the problem and answer the following questions in

all cases:

• Did the equipment work at all or was it defective from the beginning?

• Did you notice anything (symptom or defect) prior to the failure?

• What malfunction does the equipment have in your opinion (main symptom)?

Describe this malfunction.

Anl_GC_DP_1340_G_SPK7.indb 20 21.08.2019 15:14:24

Andere Handbücher für GC-DP 1340 G

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere EINHELL Wasserpumpe Handbücher

EINHELL

EINHELL RG-DP 1135 N Bedienungsanleitung

EINHELL

EINHELL GE-SP 4390 N-A LL ECO Bedienungsanleitung

EINHELL

EINHELL AQUINNA 18/30 F LED Bedienungsanleitung

EINHELL

EINHELL GE-PP 1100 N-A Bedienungsanleitung

EINHELL

EINHELL 41.709.55 Bedienungsanleitung

EINHELL

EINHELL 41.706.11 Bedienungsanleitung

EINHELL

EINHELL Royal TMP 550-iS Bedienungsanleitung

EINHELL

EINHELL 400 RB Bedienungsanleitung

EINHELL

EINHELL BG-WW 636 Bedienungsanleitung

EINHELL

EINHELL BG-WW 1355 NN Bedienungsanleitung

EINHELL

EINHELL ROYAL TMP 251-S Bedienungsanleitung

EINHELL

EINHELL BG-PP 1750 N Bedienungsanleitung

EINHELL

EINHELL GH-DP 6315 N Bedienungsanleitung

EINHELL

EINHELL GP JET 1205 NIRO Bedienungsanleitung

EINHELL

EINHELL ROYAL HW 1300 Niro/Niro Bedienungsanleitung

EINHELL

EINHELL 41.704.45 Bedienungsanleitung

EINHELL

EINHELL 41.822.41 Bedienungsanleitung

EINHELL

EINHELL NRP 300 Bedienungsanleitung

EINHELL

EINHELL GC-DP 1340 G Bedienungsanleitung

EINHELL

EINHELL RG-GP 1139 Bedienungsanleitung

EINHELL

EINHELL GE-DP 18/25 Li Bedienungsanleitung

EINHELL

EINHELL GH-DP 5225 N Bedienungsanleitung

EINHELL

EINHELL 41.706.64 Bedienungsanleitung

EINHELL

EINHELL GC-PP 900 N Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung