Ekwb EK-AIO 120 D-RGB Bedienungsanleitung

INSTALLATION MANUAL

EKAIO

120 D-RGB / 240 D-RGB / 360 D-RGB

Compatible with:

Intel Socket 115X / 20xx CPUs

AMD Socket AM4 CPU

To ensure safe and easy installation, please carefully read

this manual before starting with the installation process!

1. SAFETY PRECAUTIONS 4

2. SPECIFICATIONS 4

3. ENCLOSED IN THIS PACKAGE 5

Mounting kit 5

4. INSTALLATION – INTEL LGA-115X SOCKET 6

Step 1: Removing the motherboard 6

Step 2: Attaching the backplate to the motherboard 6

Step 3: Attaching mounting screws 6

Step 4: Installing the fans to the radiator 6

Step 5: Removing the cold-plate protective cover 6

Step 6: Mounting brackets installation 6

Step 7: Pump unit installation 6

Step 8: Installing the assembly of fans and the radiator into a PC case 7

Step 9: Pump – connecting cables 7

Step 10: Fans – connecting cables 8

OPTIONAL step! Applying the thermal compound 8

5. INSTALLATION – INTEL LGA-20XX SOCKET 8

Step 1: Attaching mounting screws (LGA-20xx) 8

6. INSTALLATION – AMD AM4 SOCKET 9

Step 1: Removing the original plastic hold-down clamps (AMD) 9

Step 2: Attaching mounting screws (AMD) 9

Step 3: Installing the fans to the radiator (AMD) 9

Step 4: Removing the cold-plate protective cover (AMD) 9

Step 5: Mounting brackets installation (AMD) 9

Step 6: Pump unit installation (AMD) 9

Step 7: Installing the assembly of fans and the radiator into a PC case (AMD) 10

Step 8: Pump – connecting cables (AMD) 10

Step 9: Fans – connecting cables (AMD) 11

OPTIONAL step! Applying the thermal compound 11

7. SUPPORT AND SERVICE 11

8. SOCIAL MEDIA 11

TABLE OF CONTENT

- 4 -

This product is intended for installation by expert users only. Please, consult with a qualiﬁed

technician. Improper installation may result in damage to your equipment. EK Water Blocks

assumes no liability whatsoever, expressed or implied, for the use of these products or their

installation. The following instructions are subject to change without notice. Please visit our web

site at www.ekwb.com for updates.

1. SAFETY PRECAUTIONS

1. Keep and store the product away from the reach of children.

2. Check the component list and condition of the product before installation. If you encounter

a problem, contact the shop where you have purchased the product to get a replacement or

a refund.

3. EKWB d.o.o. is not responsible for any damages due to external causes, including but not

limited to: improper use, problems with electrical power, accident, neglect, alteration, repair,

improper installation, and improper testing.

4. CPU and motherboard are subject to damage if the product is incorrectly installed.

5. The excessive force exerted on the fan may cause damage to the fan and/or system.

6. This product is a CPU liquid cooling solution kit, comprising of individual original EKWB parts.

Combining this liquid cooling unit with parts, other than EK Water Block products, may lead to

warranty loss.

7. Product design and speciﬁcations may be revised to improve quality and performance.

2. SPECIFICATIONS

Model EK-AIO 120 D-RGB EK-AIO 240 D-RGB EK-AIO 360 D-RGB

Radiator Dimensions 155x120x27 mm 275x120x27 mm 395x120x27 mm

Fin material Al, Cu Al, Cu Al, Cu

Fan

Dimensions 120x120x25 mm 120x120x25 mm (2x) 120x120x25 mm (3x)

Speed

600-2200

RPM ±10%

(PWM: 25-100%)

600-2200

RPM ±10%

(PWM: 25-100%)

600-2200

RPM ±10%

(PWM: 25-100%)

Air Flow 77 CFM 77 CFM 77 CFM

Life Expectancy 50,000 hours 50,000 hours 50,000 hours

Noise Level 33.5 dB 33.5 dB 33.5 dB

Bearing Type Fluid Dynamic bearing

(FDB)

Fluid Dynamic bearing

(FDB)

Fluid Dynamic bearing

(FDB)

Connector 4-Pin 4-Pin 4-Pin

Rated Voltage 12V 12V 12V

Pump

Dimensions (mm) 88x70x53 mm 88x70x53 mm 88x70x53 mm

RPM 450-2600 RPM ± 10%

(PWM: 20-100%)

450-2600 RPM ±10%

(PWM: 20-100%)

450-2600 RPM ±10%

(PWM: 20-100%)

Life Expectancy 50,000 hours 50,000 hours 50,000 hours

Noise Level 23 dB 23 dB 23 dB

Input Current 0.65 ±10% A 0.65 ±10% A 0.65 ±10% A

- 5 -

3. ENCLOSED IN THIS PACKAGE

EK-Vardar S 120ER D-RGB Fan

(1x / 2x / 3x – number of fans depends on the AIO version)

EK-AIO 120 D-RGB unit /

EK-AIO 240 D-RGB unit /

EK-AIO 360 D-RGB unit

(1x)

A tube of Thermal Paste (3830046998446 - EK-TIM Ectotherm (1g))

(1x)

Fan Cable Y-splitter

Mounting Kit (1x)

User Manual (1x)

Mounting kit

Phillips Head Screw UNC 6-32 x 30mm

(5 mm thread length)

ZIP BAG 1 FAN MOUNTING SCREWS

Phillips Head Screw UNC 6-32 x 34mm

Phillips Head Screw

UNC 6-32 x 6mm

Thumb nut (Intel /AMD)

ZIP BAG 2 INSTALLATION HARDWARE

Mounting thumb screw for Intel LGA

20XX socket

Mounting thumb screw for INTEL

LGA 115x / AMD AM4 socket

Mounting Plate Phillips Head M4x4mm

(for the installation of mounting

brackets)

Spring

Intel LGA 115x Backplate

ZIP BAG 3 BACKPLATE, MOUNTING BRACKETS, AND ACCESSORIES

AMD mounting bracket

Intel mounting bracket

EK-AIO 240 EK-AIO 360

- 6 -

4. INSTALLATION  INTEL LGA115X SOCKET

Step 1: Removing the motherboard

If your PC case doesn't have a cutout from the

bottom CPU side of the motherboard, you will

ﬁrst need to remove the motherboard from

your computer.

Step 2: Attaching the backplate to the

motherboard

Install the Intel backplate for LGA-115x socket

to the back of your motherboard. Align the

holes on the motherboard with the holes on

the backplate.

Intel LGA 115x

Backplate

Step 3: Attaching mounting screws

Install 4x LGA-115x mounting thumb screws

through your motherboard to the backplate.

Mounting thumb

screw for INTEL

LGA 115x / AMD

AM4 socket

Step 6: Mounting brackets

installation

Use four M4x4 screws to install two Intel

brackets onto the pump unit.

Be careful not to touch or damage the pre-

applied thermal compound!

M4x4

Intel

Mounting

Bracket

Step 4: Installing the fans to the

radiator

Attach the fans (1x, 2x or 3x, depending on the

AIO version) to the radiator using the UNC 6-32

x 30mm screws.

UNC

6-32 x 30 mm

Fan Radiator

Step 5: Removing the cold-plate

protective cover

Remove the protective cover from the

backside of the pump unit. It is there only to

prevent the damage of the cold-plate and the

pre-applied thermal compound that is on the

cold-plate.

When removing the protective cover and

proceeding with installation be careful not

to touch or damage the pre-applied thermal

compound!

Step 7: Pump unit installation

Wipe the CPU’s contact surface (using a

non-abrasive cloth pr a Q-tip as shown in the

sample image).

Align the pump unit over the mounting screws

and CPU as shown in the picture.

Place the enclosed compression springs and

thumb nuts over the mounting screws (4x). Start

fastening two thumb nuts at a time, preferably

in cross pattern, and do not tighten them fully

until all of them are partially screwed in.

Thumb Nut

Spring

Non-abrasive

cloth IHS

Protective

Cover

Pre-applied

thermal

Compound

- 7 -

Step 9: Pump – connecting cables

D-RGB

Connector

VDG Connector

4-pin Connector

Step A:

Plug the 4-pin PWM connector of the pump to

the motherboard.

D-RGB Header

RGB Header

Step B:

Plug the 3-pin connector of the pump’s

D-RGB LED light to the D-RGB HEADER on

the motherboard. The LED will work if the pin

layout on the header is as follows: +5V, Digital,

Empty, Ground. With some motherboards, you

can alternatively use a VDG connector instead

of a D-RGB to connect the LED.

Please ensure that the arrow

indicated on the connector is

plugged into the +5V line as

indicated on your motherboard. If

you put LED Diode to the 12V RGB

HEADER you can damage the LEDs.

Connector is the same on D-RGB

and RGB versions, but D-RGB

version has 3 cables from connector

to PCB; RGB version has 4 cables. If

you connect D-RGB led to ordinary

RGB header you can damage your

motherboard or LED strip.

Step 8: Installing the assembly of

fans and the radiator into a PC case

Attach the assembly of the radiator and the

fan(-s) to the PC case with the UNC 6-32 x

6mm screws.

UNC 6-32 x 6 mm

(4x)

UNC 6-32 x 6 mm

(8x)

UNC 6-32 x 6 mm

(12x)

EK-AIO 120 D-RGB

EK-AIO 240 D-RGB

EK-AIO 360 D-RGB

- 8 -

Step 10: Fans – connecting cables

Fan D-RGB LED Light

Connector

Fan Connector

Step A:

OPTION 1:

Connect the 4-pin PWM connector from the

fan cable directly to the CPU fan-header on the

motherboard. Always use the CPU fan-header

if possible.

OPTION 2:

In the case of EK-AIO 240 D-RGB and EK-AIO

360 D-RGB versions (with 2 or 3 fans), you may

connect the connectors from each of the fans

with the connectors on the Y-splitter cable and

then connect the Y-splitter connector to the

fan-header on the motherboard. Always use

the CPU fan-header if possible.

Y-splitter

Fan Connector

Step B:

OPTION 1:

Plug the 3-pin connector for D-RGB LED light

of the fan(-s) to the D-RGB HEADER on the

motherboard.

D-RGB Header

RGB Header

OPTION 2:

In the case of EK-AIO 240 D-RGB and EK-AIO

360 D-RGB versions, you may ﬁrst connect 2

or 3 fans together in a “daisy-chain” connection

and then connect them all together to a D-RGB

header on the motherboard.

5. INSTALLATION  INTEL LGA20XX SOCKET

Step 1: Attaching mounting screws

(LGA-20xx)

LGA-20xx (2066 / 2011 V3 / 2011) socket

motherboards do not require backplate

installation. Install 4x LGA-20XX mounting

thumb screws into M4 threaded stubs on the

integrated latch mechanism (ILM) of the LGA-

20XX socket.

Continue installation by following

the instructions from Step 4 on

page 6

OPTIONAL step! Applying the

thermal compound

This step is relevant only in the case of a

second installation of AIO or if you have

damaged the pre-applied paste on the

backside of the pump unit! For the ﬁrst

installation, you don’t need to apply the

additional thermal compound to the CPU’s

contact surface!

Wipe the CPU’s contact surface (using a

non-abrasive cloth or a Q-tip as shown in the

sample image). On a clean IHS, apply a line

of thermal compound and spread it over the

whole CPU heat spreader (IHS) with a credit

card or something similar.

Non-abrasive

cloth IHS

Fan

Connector

LGA-2011 M3

Thumb Screw

- 9 -

6. INSTALLATION  AMD AM4 SOCKET

Step 1: Removing the original plastic

hold-down clamps (AMD)

Using Philips-head screwdriver, remove the 4

UNC 6-32 screws securing the original plastic

hold-down clamps around the socket as

shown in the image. Keep the original AMD®

backplate and remove the hold-down clamps

to store them away. See the image for further

part identiﬁcation.

Step 2: Attaching mounting screws

(AMD)

Install 4x mounting thumb screw for AMD

AM4 socket onto your motherboard. The

screws are to be installed without the use of

tools (i.e. pliers).

Mounting thumb

screw for INTEL

LGA 115x / AMD

AM4 socket

Hold-down

clamps

UNC 6-32 Screws

Step 3: Installing the fans to the

radiator (AMD)

Attach the fans (1x, 2x or 3x, depending on the

AIO version) to the radiator with the UNC 6-32

x 30mm screws.

UNC

6-32 x 30 mm

Fan Radiator

Step 5: Mounting brackets

installation (AMD)

Use four M4x4 screws to install two AMD

brackets onto the pump unit.

Be careful not to touch or damage the pre-

applied thermal compound!

M4x4

AMD

Mounting

Bracket

Step 4: Removing the cold-plate

protective cover (AMD)

Remove the protective cover from the

backside of the pump unit. It is there only to

prevent the damage of the cold-plate and the

pre-applied thermal compound that is on the

cold-plate.

When removing the protective cover and

proceeding with installation be careful not

to touch or damage the pre-applied thermal

compound!

Step 6: Pump unit installation (AMD)

Wipe the CPU’s contact surface (using a

non-abrasive cloth pr a Q-tip as shown in the

sample image).

Align the pump unit over the mounting screws

and CPU as shown in the picture.

Place the enclosed compression springs and

thumb nuts over the mounting screws (4x). Start

fastening two thumb nuts at a time, preferably

in cross pattern, and do not tighten them fully

until all of them are partially screwed in.

Thumb Nut

Spring

Non-abrasive

cloth IHS

Protective

Cover

Pre-applied

thermal

Compound

- 10 -

Step 8: Pump – connecting cables

(AMD)

D-RGB

Connector

VDG Connector

4-pin Connector

Step A:

Plug the 4-pin PWM connector of the pump to

the motherboard.

D-RGB Header

RGB Header

Step B:

Plug the 3-pin connector of the pump D-RGB

LED light to the D-RGB HEADER on the

motherboard. The LED will work if the pin

layout on the header is as follows: +5V, Digital,

Empty, Ground. With some motherboards, you

can alternatively use a VDG connector instead

of a D-RGB to connect the LED.

Please ensure that the arrow

indicated on the connector is

plugged into the +5V line as

indicated on your motherboard. If

you put LED Diode to the 12V RGB

HEADER you can damage the LEDs.

Connector is the same on D-RGB

and RGB versions, but D-RGB

version has 3 cables from connector

to PCB; RGB version has 4 cables. If

you connect D-RGB led to ordinary

RGB header you can damage your

motherboard or LED strip.

Step 7: Installing the assembly of fans

and the radiator into a PC case (AMD)

Attach the assembly of the radiator and the

fan(-s) to the PC case with the UNC 6-32 x

6mm screws.

UNC 6-32 x 6 mm

(4x)

UNC 6-32 x 6 mm

(8x)

UNC 6-32 x 6 mm

(12x)

EK-AIO 120 D-RGB

EK-AIO 240 D-RGB

EK-AIO 360 D-RGB

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-MOSFET ASUS M7G Leitfaden

ekwb

ekwb EK-FC R9 Nano Series Handbuch

ekwb

ekwb EK-FC1080 GTX JetStream Bedienungsanleitung

ekwb

ekwb MSI MPG Z490 Carbon EK X Bedienungsanleitung

ekwb

ekwb EK-FC 770 GTX DCII Handbuch

ekwb

ekwb EK-FB ASUS R4BE Monoblock Bedienungsanleitung

ekwb

ekwb EK-FB RE2 Leitfaden

ekwb

ekwb EK-FC7970 Handbuch

ekwb

ekwb EK-FC980 GTX Classy Handbuch

ekwb

ekwb EK-XTOP Revo D5 PWM Handbuch

ekwb

ekwb EK-FC480 GTX Handbuch

ekwb

ekwb EK-Nucleus AIO CR360 Lux D-RGB Bedienungsanleitung

ekwb

ekwb EK-FB ASUS M8I Monoblock Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector Trio RTX 2080 Ti Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX FTW2 Bedienungsanleitung

ekwb

ekwb EK-FC7970 DCII Leitfaden

ekwb

ekwb EK-FC470 GTX Handbuch

ekwb

ekwb EK-FC RX-480 Bedienungsanleitung

ekwb

ekwb 3831109816202 Leitfaden

ekwb

ekwb EK-FC680 GTX FTW Leitfaden

ekwb

ekwb EK-FB MSI Z270 GAMING Monoblock Handbuch

ekwb

ekwb EK-Quantum Momentum ROG Crosshair VIII Hero Bedienungsanleitung

ekwb

ekwb EK-FB ASUS ROG R6E Monoblock Bedienungsanleitung

ekwb

ekwb EK-FC670 GTX Backplate Handbuch

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

ekwb EK-AIO 120 D-RGB Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken