Ekwb EK-FB ASUS M8E Monoblock Series Bedienungsanleitung

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on December 15th 2015

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual before through before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of ASUS Maximus VIII Extreme motherboard

STEP 1: PREPARING YOUR MOTHERBOARD

STEP 2: PREPARING YOUR MOTHERBOARD

REMOVING STOCK COOLER. Remove all encircled screws. There are 5 screws on

the back of the motherboard that need to be removed in order to remove the

factory installed MOSFET heat pipe cooling solution. Please store away the two

factory backplates as they will be reused. The plastic I/O shield must also be

removed. In order to do so you must remove the 3 screws on the backside of the

motherboard.

1. APPLYING THERMAL COMPOUND. Apply thermal compound on CPU heat

spreader (IHS) - see sample photo on right with enclosed EK-TIM Ectotherm

thermal grease.

The quantity of about two rice grains is just about right. There is no need to cover

the whole IHS. Applying too much thermal grease will have negative impact on the

cooling performance!

2.. CUTTING THERMAL PADS. Your block comes with thermal pads which needs to be trimmed in order to fit the voltage regulation area (MOSFET) on the

motherboard’s circuit board. WARNING: DIMENSIONS ON PICTURES BELOW ARE SCALED.

Replacement thermal pads @ EKWB web shop:

Thermal PAD F 1mm - (120x16mm) [EAN: 3830046996732]

Do not remove

the PCH (SB)

Cooler!

Installation manual for EK-FB ASUS M8E Monoblock water block

1. Thermal pad F–1.0mm

(for mosfets and inductor coils):

CPU socket

Z170 PCH (SB)

Mosfets

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on December 15th 2015

STEP 3: PLACING THE BLOCK ON TO MOTHERBOARD

PLACING THE BLOCK ON THE MOTHERBOARD. Place the EK-FB ASUS M8E Monoblock series water block gently to the motherboard or vice versa (as shown on photo

below). Make sure that mounting holes are aligned.

STEP 4: ATTACHING BLOCK ON TO THE MOTHERBOARD

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block.

A) Mosfet part: Use four M2,5x8 DIN 7985 with factory backplates. Tighten the

screws evenly. Do not forget to use one M2,5x4 DIN 7985 screw below the socket

backplate. Do not use excessive force when tightening the screws!

B) CPU part: Use four M4x8 DIN7984 with screws and washers.

Tighten the screws using enclosed 2.5mm allen key.

Use the enclosed screws and washers as shown in picture below:

For the EK-FB ASUS M8E Monoblock series water block to operate properly the G1/4

port nearest to the right edge of the water block MUST BE USED AS THE INLET

PORT. EK recommends the use of EK-ACF fittings. When using fittings other than EK-

ACF series please use hose clamps or appropriate substitute to secure the tubing to

the barb. The use of biocide containing and corrosion inhibiting coolant is always

recommended for any liquid cooling system.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver Allen key

Tubing

IMPORTANT: USE

THIS OPENING AS

AN INLET PORT!

M2,5x8 screws

PVC washer

M4x8

screws

Factory backplates

M2,5x4 screw

3. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads on PCB as

shown on the picture

PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL

PADS PRIOR TO INSTALLATION!

Place 1mm thermal pads in larger strips over

marked areas and make sure all mosfet chips

and inductor coils are covered.

Dieses Handbuch passt für folgende Modelle

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-BAY DCP 2.2 Handbuch

ekwb

ekwb EK-XRES Revo D5 Bedienungsanleitung

ekwb

ekwb EK-FC7970 DCII Leitfaden

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Bedienungsanleitung

ekwb

ekwb EK-FB ASUS M6I Leitfaden

ekwb

ekwb EK-PRO GPU WB RTX A4090 Bedienungsanleitung

ekwb

ekwb EK-FC 5970 Handbuch

ekwb

ekwb EK-FB ASUS C6H Monoblock Bedienungsanleitung

ekwb

ekwb EK-FC680 GTX FTW Leitfaden

ekwb

ekwb EK-AIO 280 D-RGB Bedienungsanleitung

ekwb

ekwb EK-Quantum Momentum TRX40 Aorus Master Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX JetStream Bedienungsanleitung

ekwb

ekwb EK-Vector Radeon VII Bedienungsanleitung

ekwb

ekwb EK-FB ASR Z77 Extreme11 Leitfaden

ekwb

ekwb EK-Reservoir Combo DCP 2.2 Handbuch

ekwb

ekwb EK-FC Terminal Bedienungsanleitung

ekwb

ekwb EK-Quantum Reaction AIO RX 6800/6900 D-RGB P240 - AMD Radeon... Bedienungsanleitung

ekwb

ekwb EK-FC780 GTX HOF Series Handbuch

ekwb

ekwb EK-FC980 GTX Ti Strix Handbuch

ekwb

ekwb EK-FC Titan Series Handbuch

ekwb

ekwb EK-Classic AM4 D-RGB Bedienungsanleitung

ekwb

ekwb EK-Vector RTX Aorus 2080Ti Bedienungsanleitung

ekwb

ekwb EK-FC980 GTX Classy Handbuch

ekwb

ekwb EK-FC770 GTX GW Leitfaden

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

ekwb EK-FB ASUS M8E Monoblock Series Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken