Ekwb EK-FB ASUS PRIME X299 Monoblock Bedienungsanleitung

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on September 6th 2017

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual thoroughly before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of ASUS PRIME X299-DELUXE motherboard

BAG CONTENT: Bag content is universal for all water blocks, you may not need all screws.

STEP 1: PREPARING YOUR MOTHERBOARD

STEP 2: PREPARING YOUR MOTHERBOARD

REMOVING STOCK COOLER. Remove all encircled screws. There are 2 screws on

the back of the motherboard that need to be removed in order to remove the

factory installed MOSFET heat pipe cooling solution. Please store away the factory

backplate as it will be reused.

1. APPLYING THERMAL COMPOUND. Apply thermal compound on CPU heat

spreader (IHS) - see sample photo on right with enclosed EK-TIM Ectotherm thermal

grease.

The quantity of about two rice grains is just about right. There is no need to cover

the whole IHS. Applying too much thermal grease will have negative impact on the

cooling performance!

2. CUTTING THERMAL PADS. Your block comes with thermal pads which needs to be trimmed in order to fit the voltage regulation area (MOSFET) on the motherboard’s

circuit board. WARNING: DIMENSIONS ON PICTURES BELOW ARE SCALED.

Replacement thermal pads @ EKWB web shop:

Thermal PAD F 1mm - (120x16mm) [EAN: 3830046996732]

Installation manual for EK-FB ASUS PRIME X299 Monoblock water block

Mosfets

CPU socket

X299 PCH

(SB)

1. Thermal pad F–1.0mm

(for mosfets):

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on September 6th 2017

STEP 3: PLACING THE BLOCK ON TO MOTHERBOARD

STEP 4: ATTACHING BLOCK ON TO THE MOTHERBOARD

PLACING THE BLOCK ON THE MOTHERBOARD. Place the EK-FB ASUS PRIME X299

Monoblock series water block gently to the motherboard or vice versa (as shown on

photo below). Make sure that mounting holes are aligned. Place it on factory installed

washers on the motherboard (MOSFET area).

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block.

A) Mosfet part: Use two M2,5x7 AX1 screws with original backplate. Tighten the

screws evenly. Do not use excessive force when tightening the screws!

B) CPU part: Use four thumb nuts with screws and washers. Tighten

the thumb nuts.

Use the enclosed screws and washers as shown in picture below:

STEP 5: CONNECTING THE D-RGB LED STRIP (optional)

Plug the 4-pin connector from Monoblock RGB LED strip to the motherboard. Please

ensure that the arrow indicated on the connector is plugged into the 12v line as

indicated on your motherboard. Failure to do so will damage your motherboard or

LED strip.

For the EK-FB ASUS PRIME X299 Monoblock series water block to operate properly

the G1/4 port nearest to the right edge of the water block MUST BE USED AS THE

INLET PORT. EK recommends the use of EK-ACF fittings. When using fittings other

than EK-ACF series please use hose clamps or appropriate substitute to secure the

tubing to the barb. The use of biocide containing and corrosion inhibiting coolant is

always recommended for any liquid cooling system.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver Allen key

3. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads on

PCB as shown on the picture

PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE

THERMAL PADS PRIOR TO INSTALLATION!

Place 1mm thermal pads in large strip

over marked area and make sure all

mosfet chips are covered.

M3 PVC Washer

Factory backplate

M2.5x7 screws

M3 thumb nut

Tubing

IMPORTANT: USE

THIS OPENING AS

AN INLET PORT!

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-PRO GPU WB AMP/Trinity RTX 4090 - Ni +... Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Bedienungsanleitung

ekwb

ekwb EK X Series Bedienungsanleitung

ekwb

ekwb EK-PRO GPU WB RTX 30 0 Series Bedienungsanleitung

ekwb

ekwb EK-FB ASUS ROG R6E Monoblock Bedienungsanleitung

ekwb

ekwb EK-PRO GPU WB AMP-Trinity RTX 4090 Ni+Inox Bedienungsanleitung

ekwb

ekwb EK-FC R9 Fury X Leitfaden

ekwb

ekwb EK-FB ASUS R5-E10 Leitfaden

ekwb

ekwb EK-FC R9-290X Backplate Handbuch

ekwb

ekwb EK-PRO GPU WB H100 Rack - Nickel + Inox Bedienungsanleitung

ekwb

ekwb EK-FC690 Leitfaden

ekwb

ekwb EK-FC 5870 V2 Handbuch

ekwb

ekwb EK-FB GA AMD KIT Handbuch

ekwb

ekwb Velocity-AMD Bedienungsanleitung

ekwb

ekwb EK-FC4890CF Leitfaden

ekwb

ekwb EK-FB GA Z87X-OC Force Leitfaden

ekwb

ekwb EK-Quantum Reflection Uni 140 D5 PWM D-RGB Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector Trinity RTX 3080/3090 Bedienungsanleitung

ekwb

ekwb EK-FC780 GTX Jetstream Handbuch

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Bedienungsanleitung

ekwb

ekwb EK-FC I750 SSD Series Handbuch

ekwb

ekwb EK-FB KIT GA Z97X-SOC Force Leitfaden

ekwb

ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

ekwb EK-FB ASUS PRIME X299 Monoblock Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken