Ekwb EK-FB ASUS Max4 Extreme Leitfaden

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 18hof May, 2011.

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box or our home page.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings. The use of an algaecide and corrosion inhibitors is always recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of ASUS Maximus IV Extreme PCB design

STEP 2: PREPARING YOUR MOTHERBOARD

1. REMOVING STOCK COOLER. Remove all 8 screws holding the original heat-

pipe cooler / backplate assembly to the motherboard’s circuit board.

2. CLEANING THE PCB. Carefully detach the original stock cooler after removing all

screws securing it to the board. Wipe off the remains (by using non–abrasive cloth or qtip,

as shown on sample photo) of the original thermal compound until the components and

circuit board are completely clean. EKWB does not recommend using any liquids for

removing paste.

3. APPLYING THERMAL COMPOUND

Apply thermal compound: lightly coat the NF200 (NB) and P67 PCH (SB chips with

for example Arctic Cooling MX-2 ™or MX-4 ™ thermal grease. EKWB recommends

to apply thermal grease in cross form for best performance (see sample picture).

4. CUTTING THERMAL PADS. Two (2) 90x15x1mm thermal pads are enclosed with your

EK-FB Max4 Extreme water block. You will have to cut the thermal pad in order to cover all

marked surfaces surface. (WARNING: DIMENSIONS ON PICTURES BELLOW ARE SCALED!)

5. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads you cut on PCB as shown on picture bellow. (PLEASE REMOVE FOIL OF THERMAL PADS ON

BOTH SIDES PRIOR TO INSTALLATION.)

P67 Southbridge

NF200

bridge chip

CPU socket

Installation and mounting manual for EK-FB ASUS Max4 Extreme water block:

Mosfets

Apply thermal grease on

Northbridge (NF200) and

Southbridge (P67).

Place 1mm thermal pads here and make

sure all chips are covered.

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 18hof May, 2011.

STEP 3: PREPARING YOUR WATER BLOCK

1. ATTACHING STANDOFFS. Apply small amount of thermal grease around mounting

holes and place acetal standoffs on NB & MOSFET part of the waterblock (thickness 2,1

mm) so the holes are concentric. Use two 3,3mm acetal standoffs on the SB part of the

waterblock to make one 6,6mm standoff. Thermal paste provides enough adhesive force

for standoffs to stay in a place for easier installation. This is a crucial step!

2. PLACING BLOCK OVER MB. Place the motherboard on the inverted water blocks

or vice versa and attach them with enclosed screws as shown. Make sure that

mounting holes are aligned.

STEP 4: ATTACHING BLOCK TO MOTHERBOARD

MOUNTING THE BLOCK.

For

perfect thermal contact, the block does not use a spring mounting system; therefore when attaching be very careful to tighten all screws equally.

Tightening the screws beginning in the center of the block near the northbridge, and continue evenly outwards. Do not use too much pressure

screws, because motherboard might

bend and either cause bad contact with water block, or break a connection on the circuit board.

Use the enclosed screws and washers as shown in diagram below:

STEP 5: CHECKING FOR CONTACTS

Temporarily r

emove the water block to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat

steps 3 and 4 to reattach the block. Block was tested on physical hardware. Due to height variations of chipset some differences may occur. In case you have problem with block

contacts please write to our support mail.

STEP 6: POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT

Screw in fittings as shown in picture, attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. Please use spacer if you use fitting with G1/4 thread

longer than 5mm. Attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. EKWB recommends using EK-PSC compression fittings with the EK-FB

Max4 Extreme series water blocks. The use of an market proved algaecide is always recommended for any liquid cooling system. You can use any opening as an inlet/outlet

port.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver 6 screws M2.5x6 DIN7985 2 screws M3x12 DIN7985 8 PVC washers

EK-PSC compression fitting

Two 3,3mm

standoffs combined

on the SB part of

the waterblock

2,1mm standoffs

Use two (2) enclosed M3x12 DIN7985

screws on the southbridge part of the

waterblock!

PVC washer

M2.5x6 DIN7985

screw

philips head screwdriver

ROG LED socket

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-Quantum Vector TUF RX 6800 Bedienungsanleitung

ekwb

ekwb Supremacy EVO Bedienungsanleitung

ekwb

ekwb EK-Dual DDC X-Top CSQ Handbuch

ekwb

ekwb EK-RAM Dominator Handbuch

ekwb

ekwb EK-FC1080 GTX FTW Bedienungsanleitung

ekwb

ekwb EK-FC1070 GTX Bedienungsanleitung

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti Bedienungsanleitung

ekwb

ekwb EK-UNI Holder D5 V3 Handbuch

ekwb

ekwb EK-XRES 140 Revo D5 Series Leitfaden

ekwb

ekwb EK-FC Titan X Leitfaden

ekwb

ekwb EK-Vector Strix RTX 2070 Backplate Leitfaden

ekwb

ekwb EK-MOSFET ASUS M7G Leitfaden

ekwb

ekwb EK-FC980 Handbuch

ekwb

ekwb EK-FB ASUS M5E Leitfaden

ekwb

ekwb EK-FC1080 G1 GTX Backplate Leitfaden

ekwb

ekwb EK-Quantum Momentum Aorus X570 Master D-RGB -... Bedienungsanleitung

ekwb

ekwb EK-FB KIT GA P67A UD7 Handbuch

ekwb

ekwb ASUS Z9PE-D8 Bedienungsanleitung

ekwb

ekwb MSI MPG Z490 Carbon EK X Bedienungsanleitung

ekwb

ekwb EK-7970 Leitfaden

ekwb

ekwb EK-FC1080 GTX G1 Bedienungsanleitung

ekwb

ekwb EK-Annihilator EX/EP Series Bedienungsanleitung

ekwb

ekwb EK-FC Titan Z Handbuch

ekwb

ekwb EK-FC1080 GTX Backplate Leitfaden

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

ekwb EK-FB ASUS Max4 Extreme Leitfaden

Beliebte Computerhardware Handbücher anderer Marken