Ekwb EK-FB KIT GA P67A UD7 Handbuch

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 11th of January, 2011.

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings.

STEP 1: GENERAL INFORMATION Sample photo of GIGABYTE GA-P67A-UD7 / GA-P67A-UD7-B3 PCB design

STEP 2: PREPARING YOUR MOTHERBOARD

1. REMOVING STOCK COOLER. Remove all 10 screws holding the original heat-

pipe cooler assembly to the motherboard’s circuit board.

2. CLEANING THE PCB. Carefully detach the original stock cooler after removing all

screws securing it to the board. Wipe off the remains (by using non–abrasive cloth or qtip,

as shown on sample photo) of the original thermal compound until the components and

circuit board are completely clean. EKWB does not recommend using any liquids for

removing paste.

3. APPLYING THERMAL COMPOUND

Apply thermal compound: lightly coat the NF200 (NB) and P67 PCH (SB chips with

- for example Arctic Cooling MX2 ™, MX3 ™or MX4 ™- thermal compound.

Follow this link:

http://www.arctic-cooling.com/catalog/images/install_mx2_retail.pdf for detailed

instructions. EKWB recommends to apply thermal grease in cross form (see

sample picture).

4. CUTTING THERMAL PADS. Three thermal pads - two 90x15x1 mm and one

20x20x1.5mm - are enclosed with your water block kit. You will have to cut out small chunk

from one thermal pad in order to cover all marked surfaces surface. (WARNING:

DIMENSIONS ON PICTURES BELLOW ARE SCALED!)

5. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads you cut on PCB as shown on picture bellow. (PLEASE REMOVE FOIL OF THERMAL PADS ON

BOTH SIDES PRIOR TO INSTALLATION.)

P67 Southbridge

NF200

bridge chip

Mosfets

CPU socket

Place 1mm thermal pads here and make

sure all chips are covered.

Place 1.5mm

thermal pads here

Installation and mounting manual for EK-FB KIT GA P67A (UD7) water block:

Apply thermal grease on

Northbridge (NF200) and

Southbridge (P67).

1mm

1.5mm

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 11th of January, 2011.

STEP 3: PREPARING YOUR WATER BLOCK

1. ATTACHING STANDOFFS. Apply small amount of thermal grease around mounting

holes and place acetal standoffs on NB/SB block (thickness 2,1 mm) so the holes are

concentric. Thermal paste provides enough adhesive force for standoffs to stay in a place

for easier installation. This is a crucial step!

2. PLACING BLOCK OVER MB. Place the motherboard on the inverted water blocks

or vice versa and attach them with enclosed screws as shown. Make sure that

mounting holes are aligned. Force the PCIe latch (marked blue) towards lower PCIe

slot when installing the NB/SB part of the block.

STEP 4: ATTACHING BLOCK TO MOTHERBOARD

MOUNTING THE BLOCK.

For

perfect thermal contact, the block does not use a spring mounting system; therefore when attaching be very careful to tighten all screws equally.

Tightening the screws beginning in the center of the block near the northbridge, and continue evenly outwards. Do not use too much pressure

screws, because motherboard might

bend and either cause bad contact with water block, or break a connection on the board.

Use the enclosed screws and washers as shown in diagram below:

STEP 5: CHECKING FOR CONTACTS

Temporarily r

emove the water block to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat

steps 3 and 4 to reattach the block. Block was tested on physical hardware. Due to height variations of chipset some differences may occur. In case you have problem with block

contacts please write to our support mail.

STEP 6: POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT

Screw in fittings as shown in picture, attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. The EK-FB KIT GA P67A (UD7) series are not sold

with high flow fittings. To ensure that the tubes are securely attached to the barb fittings, please use hose clamps or an appropriate substitute. The use of an market proved

algaecide is always recommended for any liquid cooling system. You can use any opening as an inlet/outlet port.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver 10 screws M2.5x6 DIN7985 10 PVC washers

Fitting

Use M2.5x6 screws to secure the

water block to the motherboard

PVC washer

Inhaltsverzeichnis

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-UNI RAD Handbuch

ekwb

ekwb EK-FB ASUS R5-E10 Leitfaden

ekwb

ekwb EK-DBAY RES SPIN Leitfaden

ekwb

ekwb EK-FB ASUS X58 Leitfaden

ekwb

ekwb EK-FCW9000 Leitfaden

ekwb

ekwb EK-FC780 GTX HOF Series Handbuch

ekwb

ekwb EK-FB ASUS ROG R6E Monoblock Bedienungsanleitung

ekwb

ekwb EK-FB KIT RE4 Handbuch

ekwb

ekwb MSI MPG Z490 Carbon EK X Bedienungsanleitung

ekwb

ekwb EK-FC670 GTX Backplate Handbuch

ekwb

ekwb EK-FC980 GTX Ti Classy KPE Handbuch

ekwb

ekwb EK-FC780 GTX Ti Handbuch

ekwb

ekwb EK-Quantum Momentum ROG Zenith II Extreme Bedienungsanleitung

ekwb

ekwb EK-FC I750 SSD Series Handbuch

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Bedienungsanleitung

ekwb

ekwb EK-FC7970 DCII Leitfaden

ekwb

ekwb EK-XRES 140 Revo D5 Series Leitfaden

ekwb

ekwb EK-FC WX9100 PRO BACKPLATE Bedienungsanleitung

ekwb

ekwb EK-Quantum Reflection Uni 140 D5 PWM D-RGB Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Backplate Leitfaden

ekwb

ekwb EK-FC580 GTX Leitfaden

ekwb

ekwb EK-FB KIT GA-X99 LE Leitfaden

ekwb

ekwb EK-FC1080 GTX FTW Leitfaden

ekwb

ekwb EK-XLC PREDATOR 240 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

ekwb EK-FB KIT GA P67A UD7 Handbuch

Beliebte Computerhardware Handbücher anderer Marken