Ekwb EK-FB ASUS ROG ZE Monoblock Bedienungsanleitung

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on October 10th 2017

REMOVING STOCK COOLER. Remove all encircled screws. There are 4 (four) screws

on the back of the motherboard that need to be removed in order to remove the

factory installed MOSFET heat pipe cooling solution. And 3 (three) screws for the

plastic factory I/O cover. Please store away the factory backplate and I/O cover as

it will be reused.

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual thoroughly before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of ASUS ZENITH EXTREME motherboard

BAG CONTENT: Bag content is universal for all water blocks, you may not need all screws.

STEP 2: PREPARING YOUR MOTHERBOARD

STEP 3: PREPARING YOUR MOTHERBOARD

APPLYING THERMAL COMPOUND. Apply thermal compound on CPU heat spreader

(IHS) - see sample photo below with enclosed thermal grease.

The quantity of about two stripes is just about right. There is no need to cover the

whole IHS. Applying too much thermal grease will have negative impact on the cooling

performance!

STEP 4: CUTTING THERMAL PADS

Your block comes with thermal pads which needs to be trimmed in order to fit the voltage regulation area (MOSFET) on the motherboard’s circuit board. WARNING:

DIMENSIONS ON PICTURES BELOW ARE SCALED.

Replacement thermal pads @ EKWB web shop:

Thermal PAD G 1mm - (120x24mm) [EAN: 3830046996770]

Installation manual for EK-FB ASUS ROG ZE Monoblock water block

Mosfets

CPU socket

AMD X399

Chipset

1. Thermal pad G–1.0mm

(for mosfets and inductor coils):

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on October 10th 2017

Place thermal pads on PCB as shown on the picture below.

PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL

PADS PRIOR TO INSTALLATION!

STEP 5: PLACING THERMAL PADS

STEP 6: PLACING A BLOCK ON TO THE MOTHERBOARD

Place the EK-FB ASUS ROG ZE Monoblock series water block gently to the motherboard

or vice versa (as shown on photo below). Make sure that mounting holes are aligned.

Place it on factory installed washers on the motherboard (MOSFET area).

STEP 7.1: ATTACHING A BLOCK ON TO THE MOTHERBOARD

STEP 7.2: ATTACHING A BLOCK ON TO THE MOTHERBOARD

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block. Secure top 4 (four)

nickel screws with enclosed 2,5mm Allen key. Tighten screws diagonally and evenly

till the end of the thread. Do not use excessive force when tightening the screws!

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block. Use 2 (two) M2,5x7 AX1

screws with original backplate. Tighten the screws evenly. Do not use excessive force

when tightening the screws! Now you can reinstall factory plastic I/O cover.

STEP 8: CONNECTING THE D-RGB LED STRIP (optional)

Plug the 4-pin connector from Monoblock D-RGB LED strip to the ADD HEADER on

the motherboard. Please ensure that the arrow indicated on the connector is plugged

into the +5V line as indicated on your motherboard. Failure to do so will damage

your motherboard or LED strip.

For the EK-FB ASUS ROG ZE Monoblock series water block to operate properly the

G1/4 port nearest to the right edge of the water block MUST BE USED AS THE INLET

PORT. EK recommends the use of EK-ACF fittings. When using fittings other than EK-

ACF series please use hose clamps or appropriate substitute to secure the tubing to

the barb. The use of biocide containing and corrosion inhibiting coolant is always

recommended for any liquid cooling system.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver Allen key

M2.5x7 screws

Tubing

IMPORTANT: USE

THIS OPENING AS

AN INLET PORT!

Place 1mm thermal pads in

large strip over marked area

and make sure all mosfet chips

and inductor coils are covered.

Dieses Handbuch passt für folgende Modelle

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-XTOP D5 Leitfaden

ekwb

ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Bedienungsanleitung

ekwb

ekwb EK-FB GA 990FXA-UD7 Handbuch

ekwb

ekwb Barebones Leitfaden

ekwb

ekwb EK-Quantum Momentum Aorus X570 Master D-RGB -... Bedienungsanleitung

ekwb

ekwb EK Series Bedienungsanleitung

ekwb

ekwb EK-FC Strix RTX 2080 Ti Backplate Classic Bedienungsanleitung

ekwb

ekwb EK-Vector Radeon VII Bedienungsanleitung

ekwb

ekwb EK-FB ASUS Strix X299-E RGB Monoblock Bedienungsanleitung

ekwb

ekwb EK-FC970 GTX TF5 TFX Series Handbuch

ekwb

ekwb EK-FC R9-280X DCII Bedienungsanleitung

ekwb

ekwb EK-FC1080 GTX FTW Leitfaden

ekwb

ekwb EK-PRO GPU WB AMP-Trinity RTX 4090 Ni+Inox Bedienungsanleitung

ekwb

ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... Bedienungsanleitung

ekwb

ekwb EK-FC780 GTX Ti Handbuch

ekwb

ekwb EK-Quantum Vector FE RTX 3080 Bedienungsanleitung

ekwb

ekwb EK-FB ASUS M6I Leitfaden

ekwb

ekwb EK-Vector RTX Aorus 2080Ti Bedienungsanleitung

ekwb

ekwb EK-FB GA AMD KIT Handbuch

ekwb

ekwb Velocity - AMD Bedienungsanleitung

ekwb

ekwb EK-FC 780 GTX Jetstream Bedienungsanleitung

ekwb

ekwb EK-Thermosphere Leitfaden

ekwb

ekwb EK-FC 780 GTX DCII Series Handbuch

ekwb

ekwb EK-DBAY RES SPIN Leitfaden

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

ekwb EK-FB ASUS ROG ZE Monoblock Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken