Elan 84200 Bedienungsanleitung

LED CHANDELIER

MODEL #84200

Français p. 9

ATTACH YOUR RECEIPT HERE

Serial Number Purchase Date

Questions, problems, missing parts? Before returning to your retailer, call our

customer service department at 1-866-558-5706, 8 a.m. - 4 p.m., EST, Monday - Friday.

PACKAGE CONTENTS

PART DESCRIPTION QTY. PART DESCRIPTION QTY.

Canopy

Mounting Bracket

LED Assembly

Swivel Connector

6” Threaded Pipe

12” Threaded Pipe

Coupling

Wire

Connector Short

Machine

Screw

Qty: 3

Qty: 2

Canopy

Screw

Qty: 2

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING

• IMPORTANT: NEVER attempt any work without shutting o the electricity.

• Go to the main fuse box, or circuit breaker, in your home. Place the main power switch in

the “OFF” position and unscrew the fuse(s), or switch “OFF” the circuit breaker switch(es),

that control the power to the ﬁxture or room that you are working on.

• Place the wall switch in the "OFF" position. If the ﬁxture to be replaced has a switch or

pull chain, place those in the "OFF" position.

• Do not touch hot LED.

• The LED light output is strong enough to injure human eyes. Precautions must be taken to

prevent looking directly at the LEDs with unaided eyes for more than a few seconds.

• California Proposition 65

WARNING: This product can expose you to lead, which is known to the State of

California to cause cancer, birth defects or other reproductive harm. For more

information go to www.p65warnings.ca.gov

CAUTION

• Read and understand all instructions and illustrations completely before proceeding with

assembly and installation of this ﬁxture.

• If you have any doubts about how to install this lighting ﬁxture, or if the ﬁxture fails to

operate completely, please contact a qualiﬁed licensed electrical contractor.

• All parts must be used as indicated in these instructions. Do not substitute any parts, leave

parts out, or use any parts that are worn out or broken. Failure to obey this instruction

could invalidate the UL listing, C.S.A. certiﬁcation, and/or ETL listing of this ﬁxture.

• This ﬁxture is intended for installation in accordance with the National Electric Code (NEC)

and all local code speciﬁcations.

• This ﬁxture is for indoor use only.

• Use ONLY the supplied LED driver to power ﬁxture.

• Driver cable is not intended for use through or concealed behind walls, ﬂoors, or ceilings.

• This ﬁxture is dimmable when using an electronic low voltage (ELV) dimmer. Note: dimmers

that specify use with LED, but are not ELV, are NOT sucient. They are designed to work

with LED “bulbs” not integrated LED ﬁxtures.

HARDWARE CONTENTS

SAFETY INFORMATION

AA BB CC DD

Thread Locking

Compound

Qty: 1

Before beginning assembly of product, make sure all parts are present. Compare parts with

package contents list. If any part is missing or damaged, do not attempt to assemble the

product.

Estimated assembly time: 30 minutes to 1 hour

Tools Required for Assembly (not included): Phillips screwdriver, ﬂathead screwdriver, wire

strippers, electrical tape, ladder, safety glasses.

Safety goggles

Phillips

screwdriver

Flathead

screwdriver Wire strippers Electrical tape

Ladder

ASSEMBLY INSTRUCTIONS

PREPARATION

Note: The electrical cable will need to get

pulled through the individual parts as they

are installed on this and later steps.

Note: The hanging height for this ﬁxture is

adjustable. Add or subtract threaded pipes

to achieve the desired height.

1. Place a drop of locking compound (DD) on

the threads on the threaded pipes. Screw 6

in. threaded pipe (E) onto 12 in. threaded

pipe (F). Connect the assembled pipes onto

coupling (G). Finially, screw swivel connector

(D) onto 6 in. threaded pipe (E).

Thread Locking

Compound x 1

Hardware Used

ASSEMBLY INSTRUCTIONS

2. Wire connection guide (outlet box to driver):

Ground wire:

For installation in the United States: Wrap

ground wire from outlet box around ground

screw preassembled on mounting bracket

(B) no less than 2 in. from wire end. Tighten

ground screw.

Supply wires:

• Connect the Neutral (White) supply wire

fromthe outlet box to the Neutral driver

input wire (White).

• Connect the Live (Black) supply wire from

theoutlet box to the Live driver input wire

(BLACK).

LIVE (HOT)

BLACK WIRE

OUTLET BOX GROUND

WIRE BARE COPPER

OR GREEN

NEUTRAL

WHITE

WIRE

Short Machine

Screw x 2

Hardware Used

3. Orient the mounting bracket (B) so that the

arms are facing away from the outlet box

(not included). Connect the mounting

bracket (B) to the outlet box with short

machine screws (BB).

Outlet Box

Arm

BB BBB

ASSEMBLY INSTRUCTIONS

BLACK

SHRINK

TUBE

DRIVER

NEUTRAL

(-) BLUE

WIRE

OUTLET BOX GROUND WIRE

BARE COPPER OR GREEN

FIXTURE LIVE

(+ HOT) RED WIRE

FIXTURE

NEUTRAL

(-) BLACK WIRE

DRIVER LIVE

(+ HOT)

RED WIRE

FIXTURE GROUND

WIRE BARE

COPPER OR GREEN

4. Wire connection guide (ﬁxture to driver):

Ground wire: Connect ﬁxture ground wire to the outlet ground wire that has been

attached to the mounting bracket ground screw.

Supply wires: **NOTE: Connect one pair of ﬁxture wires to each driver. Wire "pairs" are

bundled by shrink tubing.

• Connect the Neutral (Blue) driver output wire to the Neutral (Black) ﬁxture wire.

• Connect the Live (Red) driver output wire to the Live (Red) ﬁxture wire.

x 2

Canopy

Screw

Hardware Used

Pass canopy (A) over the arms protruding

from mounting bracket (B) then secure in

place with canopy screws (CC).

•Always be certain that electric current is turned o before cleaning this item.

•Use a soft, moist cloth with mild non-abrasive soap to clean ﬁxture. Never use glass

cleaner on ﬁxture, as it will damage the metal ﬁnish.

Fixture does not light. 1. Fixture may be wired incorrectly. 1. Check wiring.

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

TROUBLESHOOTING

CARE AND MAINTENANCE

LIMITED WARRANTY ON KICHLER® ÉLAN BRAND LIGHT FIXTURES

Kichler Lighting LLC warrants its light ﬁxtures to the original consumer purchaser to be free from defects in material and workmanship

for the applicable period speciﬁed below:

Kichler® élan Light Fixtures

One (1) year from the date of purchase by the original consumer purchaser.

Kichler® élan Light Fixtures with LED Light Engines and Electrical Components

three (3) years from the date of purchase by the original consumer purchaser on the Light Engine and all other electrical

components.

What We Will Do

Kichler Lighting LLC will repair or replace, free of charge, during the applicable warranty period (as described above), any light

ﬁxture that proves defective in material and/or workmanship under normal installation, use and service. If repair or replacement is

not practical, Kichler Lighting LLC may elect to refund the purchase price in exchange for the return of the product. These are your

exclusive remedies.

What Is Not Covered

Polished brass product ﬁnishes and non-LED light bulbs carry no warranty. Any labor charges incurred by the original consumer

purchaser to repair or replace this product are not covered by this warranty. Kichler Lighting LLC shall not be liable for any damage

to the product resulting from reasonable wear and tear, voltage overload, outdoor use (where the annual average ambient

temperature is below 27° or above 95° Fahrenheit), misuse (including use of the product for an unintended application), abuse,

neglect or improper or incorrectly performed installation, maintenance or repair, including failure to follow the applicable care and

cleaning instructions. Kichler Lighting LLC recommends using a professional electrician for all installation and repair of light ﬁxtures. We

also recommend that you use only genuine Kichler® replacement parts.

What You Must Do to Obtain Warranty Service or Replacement Parts

A warranty claim may be made, and replacement parts may be obtained by contacting the distributor from whom you purchased

the light ﬁxture. If the distributor is not available, please call 866-558-5706 or contact us by mail as follows (please include your

model number and date of purchase):

WARRANTY (continued)

Kichler Lighting LLC

7711 East Pleasant Valley Rd

Cleveland, OH 44161-8010

Proof of purchase (original sales receipt) from the original purchaser must be made available to Kichler Lighting LLC for all warranty

claims.

Limitation on Duration of Implied Warranties

TO THE EXTENT PERMITTED BY LAW, ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

OF FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY,

WHICHEVER IS SHORTER. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above

limitation may not apply to you.

Limitation of Special, Incidental or Consequential Damages

KICHLER LIGHTING LLC SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LABOR

CHARGES TO REPAIR, REPLACE, INSTALL OR REMOVE THIS PRODUCT), WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR

IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE. KICHLER LIGHTING LLC SHALL NOT BE LIABLE FOR ANY

DAMAGE TO THE PRODUCT RESULTING FROM REASONABLE WEAR AND TEAR, OVERLOAD, OUTDOOR USE (WHERE THE ANNUAL

AMBIENT TERMPERATURE IS BELOW 27° OR ABOVE 95° FAHRENHEIT), MISUSE (INCLUDING USE OF THE PRODUCT FOR AN

UNINTENDED APPLICATION), ABUSE, NEGLECT OR IMPROPER OR INCORRECTLY PERFORMED INSTALLATION, MAINTENANCE OR

REPAIR, INCLUDING FAILURE TO FOLLOW THE APPLICABLE INSTALLATION, CARE AND CLEANING INSTRUCTIONS. Some states/provinces

do not allow the exclusion or limitation of special, incidental or consequential damages, so the above limitations and exclusions may

not apply to you. Notice to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended

to apply to the fullest extent permitted by the laws of the State of New Jersey.

Additional Rights

This warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state/province to state/province.

This is Kichler Lighting LLC's exclusive written warranty and the warranty is not transferable.

Rev. 11-13-18

For replacement parts, call our customer service department at 1-866-558-5706,

8 a.m. - 4 p.m., EST, Monday - Friday.

PART DESCRIPTION PART #

REPLACEMENT PART LIST

Printed in China

Distributed by:

Kichler Lighting LLC

88 Long Hill St.

East Hartford, CT 06108

E F AA BB CC

AA BB CC

6” Threaded Pipe PIPEX06-MBK

12” Threaded Pipe

PIPEX12-MBK

Wire Connector WC001

Short Machine Screw SCR832X050

Canopy Screw CS84087

LUSTRE À DEL

MODÈLE #84200

JOIGNEZ VOTRE REÇU ICI

Numéro de série Date d’achat

Des questions, des problèmes, des pièces manquantes? Avant de retourner l’article au

détaillant, appelez notre service à la clientèle au 1 866 558-5706, entre 8 h et 16 h

(HNE), du lundi au vendredi.

Inhaltsverzeichnis

Sprachen:

Andere Elan Außenleuchte Handbücher

Elan

Elan 83335 Bedienungsanleitung

Beliebte Außenleuchte Handbücher anderer Marken

Sealey

Sealey LED37 Bedienungsanleitung

nordlux

nordlux VEJERS Benutzerhandbuch

SImx

SImx ELITE LED LHTC637 Bedienungsanleitung

GEV

GEV CAROLINE 10833 Bedienungsanleitung

NEBO

NEBO NEB-LSP-0020 Bedienungsanleitung

WE-EF

WE-EF PFL540 LED Bedienungsanleitung

Lindby

Lindby 9949029 Bedienungsanleitung

HEPER

HEPER DOGO Side LW6048.585-US Montage- und Bedienungsanleitung

HEPER

HEPER LW8034.003-US Montage- und Bedienungsanleitung

Maretti

Maretti VIBE S 14.6080.04.A Bedienungsanleitung

BEGA

BEGA 84 253 Handbuch

HEPER

HEPER MINIMO Montage- und Bedienungsanleitung

LIGMAN

LIGMAN BAMBOO 3 Bedienungsanleitung

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung

urban ambiance

urban ambiance UQL1273 Bedienungsanleitung

TotalPond

TotalPond 52238 Bedienungsanleitung

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Bedienungsanleitung