Elan PRM2 Bedienungsanleitung

ELAN HOME SYSTEMS INSTRUCTION SHEET

Introduction

The PRM2 Precision Panel Rack Mount is a rack-mounting

frame designed to be used to install any ELAN Precision

Panel into a standard 19" equipment rack. The PRM2

holds up to two full size precision panels, four 1/2 frame

precision panels using the PF2 Precision Panel Frame, or a

combination of one full size panel and two 1/2 size panels.

The PRM2 has a custom-designed hinged metal frame

which drops down 90 degrees for easy access to rear

panel punch-downs and connectors. Stainless-steel frame

support cables hold panels steady while punching down

wires.

Features

Holds Any ELAN Precision Panel

Mounts In Any Standard 19" Equipment Rack

7 Rack Spaces (7U or 12.25") Total Height

Custom-Designed Drop Down Hinge

Wire Punchdown Support Cables

Folded Flange / Heavy Gauge Electro-Galvanized

Steel For Increased Strength

Rack-Mount Screws (8) Included

Panel Screws (8) Included

Installing The PRM2 In A Rack

The PRM2 consists of two pieces. The upper frame should

be installed first, followed by the lower hinge panel. Install

the PRM2 into an equipment rack as follows:

Determine where you want to mount the PRM2 and

attach the upper frame to the equipment rack using

four of the rack screws (larger screws).

•

Attach the lower hinged panel in the rack space

directly below the upper frame using the remaining

four rack screws.

NOTE: The two flange hinges must be inserted into

the two slot openings at the base of the upper panel

blank, as shown below.

ELAN Precision Panel Installation

Note: The ELAN full and 1/2 frame precision panels can be

installed facing in either direction on the PRM2 to handle

wire punchdowns either from the rack equipment location

or from the wall.

A. Full Size Precision Panels:

Install full size ELAN Precision Panels into the PRM2

using four of the panel screws (smaller screws) that

came with the PRM2, as shown below.

PRM2 Precision Panel Rack Mount

UPPER FRAME

LOWER HINGED

PANEL

ELAN HOME SYSTEMS INSTRUCTION SHEET

HOME SYSTEMS

2428 Palumbo Dr.

Lexington, KY USA 40509

Voice 859.269.7760

Tech Support 800-622-3526

www.elanhomesystems.com

ELAN Precision Panel Installation (cont'd)

B. 1/2 Frame Precision Panels:

Note: The PF2 Precision Panel Frame is required for the

installation of all 1/2 Frame Precision Panels.

Attach a 1/2 Frame Precision Panel such as a PVSE,

PZ600 etc., into a PF2 Precision Panel Frame using

the four screws that came with the Precision Panel

as shown below in Example A.

Attach the PF2 Precision Panel Frame to the PRM2

using the four appropriate panel screws, as shown

below in Example B.

Using Punchdown Support Cables

Remove the four rack mounting screws from the

PRM2's upper frame, as shown below.

Lower the upper frame and attach the punch down

support cables from the top screw hole on each side

of the frame to an available screw hole on the rack,

as shown below.

After wire termination remove the support cables,

raise the upper frame and re-install the four screws.

P/N 9800756 REV: A

Limited Warranty

ELAN HOME SYSTEMS L.L.C. (“ELAN”) warrants the PRM2 Precision Panel Rack Mount to be free from defects in materials and workmanship for the period of ﬁve years (5 years) from date

of purchase. If within the applicable warranty period above purchaser discovers that such item was not as warranted above and promptly notiﬁes ELAN in writing, ELAN shall repair or replace

the item at the company’s option. This warranty shall not apply (a) to equipment not manufactured by ELAN, (b) to equipment which shall have been installed by other than an ELAN authorized

installer, (c) to installed equipment which is not installed to ELAN’s speciﬁcations, (d) to equipment which shall have been repaired or altered by others than ELAN, (e) to equipment which shall

have been subjected to negligence, accident, or damage by circumstances beyond ELAN’s control, including, but not limited to, lightning, ﬂood, electrical surge, tornado, earthquake, or other

catastrophic events beyond ELAN’s control, or to improper operation, maintenance or storage, or to other than normal use of service. With respect to equipment sold by, but not manufactured

by ELAN, the warranty obligations of ELAN shall in all respects conform to the warranty actually extended to ELAN by its supplier. The foregoing warranties do not cover reimbursement for

labor, transportation, removal, installation or other expenses which may be incurred in connection with repair or replacement.

Except as may be expressly provided and authorized in writing by ELAN, ELAN shall not be subject to any other obligations or liabilities whatsoever with respect to equipment manufactured by

ELAN or services rendered by ELAN.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES EXCEPT WARRANTIES OF TITLE, INCLUDING BUT NOT

LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

ATTENTION: TO OUR VALUED CONSUMERS

To ensure that consumers obtain quality pre-sale and after-sale support and service, ELAN Home Systems products are sold exclusively through authorized dealers. ELAN products are not

sold online. The warranties on ELAN products are NOT VALID if the products have been purchased from an unauthorized dealer or an online E-tailer. To determine if your ELAN reseller is

authorized, please contact ELAN Home Systems at (859) 269-7760.

UPPER FRAME

Andere Elan Rack & Stand Handbücher